Great Wall V200. Instruction — part 20
Brake-22
2. Install the piston gasket in the tong body.
a. Screw the bleed screw into the bleed hole;
b. Install the square gasket in the sealing groove of two cylinders of
pump respectively after coat its working surface with proper
rubber lubricant.
Tightening torque 7
10N
m.
3. Connect the brake pipeline
Connect the brake oil pipe to the tong.
Tightening force: 50
5N
m
4. Fill up the brake system with the brake fluid and drain the air
in the brake system.
5. Check for leakage of brake fluid.
Rear parking brake
pull-out piece
spring draw bar
hand brake
stay wire
front brake shoe
lower tension spring
clearance-adjusting bolt
clearance-adjusting gear
clearance-adjusting
bolt head
pull-out piece
spring seat
pulling arm pin
rear brake shoe
brake shoe pulling arm
saddle type washer
push pedal
push pedal
release spring
stopper
upper release spring
rear brake disc
Used component which can not be used any more.
Removal of rear brake
Remarks: When the brake torque of the hand brake cannot meet
the brake requirement, the thickness of the brake shoe gasket
shall be tested. If it is less than the minimum value of brake show
gasket, the brake shoe shall be replaced.
minimum thickness: 1.0mm
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Brake-23
1. Remove the rear wheel
2. Remove the rear brake caliper
3. Remove the rear brake disc
Remarks: If the brake disc is difficult to remove, remove the
adjust ment spout plug, insert the screwdriver into the adjust
ment spout of the rear brake bedplate, Release the brake shoe
adjustment device through twisting the clearance-adjusting gear.
4. Remove the shoe plate, pull-out the piece spring , pull-out piece
spring seat, pull-out piece spring draw bar
5. Remove the lower tension spring and clearance-adjusting device
Use clipper to remove the extension spring, release the clearance
adjusting device and remove it.
6. Remove the two upper extension springs
7. Remove the brake shoe
a. Remove the brake shoe, baffle, baffle return spring.
b. Remove the band brake stay wire from the stay and brake pulling
arm.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Brake-24
8. Remove the parking brake pulling arm
Use the screw driver to remove the parking brake pulling arm
Check and maintain the components of brake
1. Check the dismantled components
Check to se whether the dismantled components are wearing, rusted
or damaged.
2. Measure the internal diameter of the brake disc
Standard inter diameter: 210mm
maximum internal diameter: 212mm
3. Measure the thickness of the brake shoe
standard thickness: 4.0mm
minimum thickness: 1.0mm
If the thickness of the brake shoe is less than the minimum value, or
there is uneven wearing, the brake shoe shall be replaced.
Remarks: If any one of the brake shoes needs to be replaced, all
the brake shoes need to be replaced to keep the even brake
performance.
4. Check whether the contact between the brake shoe gasket and
brake disc is sound.
If the contact between the brake shoe gasket and brake disc is bad, it
should use the brake shoe grinding device to repair or replace the
brake shoe assembly.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Brake-25
1. Install the clearance-adjusting device assembly
Insert the clearance-adjusting shaft head into the clearance-adjusting
wheel; screw the clearance-adjusting screw rod into the clearance
adjusting wheel.
Remarks: The screw direction of left clearance-adjusting screw
rod is the left hand.
The screw direction of right clearance-adjusting
screw rod is the right hand.
2. Coat the following components with the proper anti-high tem
perature grease :
a. Contact position of brake soleplate and brake shoe.
b. Contacting surface of push plate and shoe plate; contacting sur-
face of clearance-adjusting device assembly and shoe plate.
Assembly of rear parking brake
Remarks: Assemble the component according to the direction shown in figure;
It is prohibited strictly that the working surface of brake drum and abrasion disk is polluted by the paint and grease. It
should be removed by the fine abrasive paper if the abrasion disk has little dirty. The brake shoe should be replaced when
the polluted area is large, otherwise it will cause the serious effect of insufficient brake force.
left wheel
front
right wheel
front
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Brake-26
2. Install the parking brake pulling arm
Install the parking brake pulling arm and use a new saddle washer.
3. Install the rear brake shoe
a. Install the parking brake pull wire on the parking brake pulling
arm.
b. Insert the end of rear brake shoe into the support pin of brake
soleplate.
Insert the pull-out piece spring pull bar into the brake soleplate and
brake shoe assembly, then insert the pull-out piece spring and pull-
out piece spring base. Use the pull-out piece spring fork to rotate
the pull-out piece spring base in position.
4. Install the front brake shoe
install the front shoe plate; insert one of its ends into the fixed pin of
soleplate.
Insert the pull-out piece spring pull bar into the brake soleplate and
brake shoe assembly, then insert the pull-out piece spring and pull-
out piece spring base. Use the pull-out piece spring fork to rotate the
pull-out piece spring base in position.
5. Install the brake push plate
Insert the push plate release spring into the push plate; then install
the push plate on the place between the front and rear brake shoe
assemblies.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Brake-27
6
Install the lower tension spring
Install the lower tension spring between the front and rear shoe plate.
7. Install the clearance-adjusting device.
Install the clearance-adjusting device after poke the brake shoe by
screwer.
8. Install two upper release springs
Insert the block into the support pin, then install the upper release
spring on the place between two brake assemblies.
9. Check the operating process of automatic adjusting mechanism.
a. Pull the instruction brake pill-wire, then release it. Check the clear-
ance-adjusting gear for rotation. If can not rotate, check the rear
brake and find the problem.
b. Adjust the clearance-adjuster to the length as short as possible.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Brake-28
10. Adjust the clearance between the brake drum and brake shoe.
Poke the adjusting hole plug on the brake drum, insert the screwdriver
into the clearance-adjusting hole; rotate the clearance-adjusting gear
to expand the brake shoe until the brake disc can not be rotated by
hand. Then rotate it for 3-5 teeth in anticlockwise, rotate the brake
disc by hand at the same time, it is proper that it can rotate freely
and without the contact between the abrasion and disc. It is allowable
that the non-running-in brake shoe has the slight abrasion sensing.
When adjust the clearance, the left and right wheel must be adjust at
the same, install the adjusting hole plug after the completion of
adjusting .
11.Rear brake caliper assembly
12.Rear wheel assembly
Tighten torque :120N.m
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Brake-29
The action of load-sensing proportional valve is to prevent the rear wheel is braked before the front wheel is braked by adjusting the
distribution of front and rear brake force according to the difference of vehicle rear shaft load, then avoid the risk of vehicle rotation.
The adjustment of proportional valve is shown as follows:
a. The rear shaft load can be 820Kg after adjustment (including driver).
b. Install the brake pressure measuring meter and drain the air.
c. Increase the front brake pressure to 12Mpa, the rear brake pressure should be within 8
9 Mpa.
d. If necessary, adjust the hydraulic pressure.
1. Move the sensing spring bracket on the rear axle, the right hook of sensing spring moves to right; the rear brake
pressure is increased .
2. Vice versa, the rear brake pressure decreases, the adjustment scope of the frame is 20mm.
3. The extension amount of spring of load sensing proportional valve is controlled within 84
95mm.
Adjustment load-sensing proportional valve
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Brake-30
Replace of load-sensing proportional valve
1. Removal
Disconnect the brake pipeline form the valve; remove the lock nut and
remove the adjusting bolt from the suspension arm bracket; remove the
installation bolt and take off the load-sensing proportional valve assembly.
2. Installation
a. Use two installation bolts to fix the load-sensing proportional valve.
The bolt tightening torque is 23N
m,
b. Tighten the adjusting bolt locking nut,
c. Connect each brake pipeline.
The tightening torque of the connector is 16N
m,
d. Filled with the brake fluid, discharge the air from the brake system;
check the brake pressure and leakage.
output manometer
input manometer
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Brake-31
Antilock Braking System (ABS)
Cautions
1.
It must not remove or install the electric elements and wire bunch plug when the ignition switch is in ON to avoid
the damage of ECU. It should turn off the ignition switch if needs disassembly.
2.
Pay attention to do not knock or impact the ABS ECU during the maintenance and repair, for it will damage the
ABS ECU easily.
3.
The wheel speed sensor and hydraulic unit (integrated with ECU) of BOSCH ABS8.0 can not be repaired, it should
be replaced in integral if damaged.
4.
After the brake system is maintained, the brake pedal maybe soft. Discharge the air according to the normal brake
system.
5.
It must use the brake fluid from original manufacturer; the brake fluid of different number cannot be used in mixed,
otherwise it will cause the failure of brake system. Select the tyre of original type as most as possible
Repair of Antilock Braking System (ABS)
1.
It should process the failure diagnosis for the brake system before process the ABS failure diagnosis. It can
diagnose out the failure rapidly by using Table 1. In Table 1, the small number means the failure which occurs most
possibly. Check each element according to the sequence and maintain or replace it if necessary.
2.
Check the following elements for normal operation before the diagnosis:
Brake fluid level and brake fluid quality
Pressure of tyre, size of tyre, shape and depth of tyre figure
Other brake component
These components will affect the brake effect of the ABS. Check the system sensor, connecting wire and connector for correct
installation, arrangement and connection. Ensure the completeness of fuse, repair or replace it if necessary.
3.
Process the analysis and diagnosis according to the ABS advanced by owner. Use the diagnosis instrument (Annex
1) for final check and confirmation. It must process the run inspection after the competition of all ABS maintenance.
The test condition is shown as follows:
a.
Confirm the tyre complies with the requirement, the tyre pressure is normal.
b.
The brake system (including brake light ) is normal
c.
The brake system is without leakage.
d.
The position and installation of wheel speed sensor is correct.
e.
All fuses are normal.
4.
test method:
Run for 1 min at least when the vehicle speed is beyond 40Km/h, process a proper brake. Then read out the failure code to
ensure the ABS is without failure code.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Brake-32
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Brake-32
Table 1
Name of element
(failure)
Brake is low or
soft
Lag of brake
Block of brake
The brake is very hard
but has bad effect
Brake
noise
Brake system (leakage of brake
fluid)
1
1
Brake system (with air)
2
2
brake shoe (worn)
3
Piston oil seal (worn or
damaged)
3
brake pedal (small free stroke)
1
Brake main pump (failure)
4
11
parking brake (brake shoe is out
of round)
4
parking brake (improper
adjustment)
2
parking brake pull-wire (lag)
3
Assist push bar (improper
adjustment)
5 9
8
Tension or release spring (failure)
8
8
brake shoe (crack or
deformation)
5
5
4 1
Piston (lag)
6
1
brake shoe (with oil)
2
5
Piston (block)
7
3
assist system (vacuum leakage)
10
9
brake shoe support plate (loose)
4
fixed bolt (loose)
2
Slide pin (worn)
5
brake drum (crack)
4
7
3
brake shoe (with foreign
material)
6 6
brake shoe (harden )
7
Noise reduction plate (worn)
9
Press spring (damaged)
10
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Steering-1
Chapter 9
Steering
Precautions. . . . . . . . . . . . . . . . . . . ...2
Troubleshooting. . . . . . . . . . . . . . . . . . 2
Inspection on vehicle. . . . . . . . . . . . . . . . .3
Steering linkage. . . . . . . . . . . . . . . . . . 4
Hydraulic power steering system. . . . . . . . . . . ...6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Steering-2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Steering-3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Steering-4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст