Citroen C4 Picasso (2017 year). Manual — part 21

319

In the event of a breakdown

C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016

Start the engine of the vehicle with the

good battery and leave it running for a
few minutes.

Operate the starter on the broken down

vehicle and let the engine run.

If the engine does not start straight
away, switch off the ignition and wait a
few moments before trying again.

Wait until the engine returns to idle then

disconnect the jump lead cables in the
reverse order.

Refit the plastic cover to the (+) terminal, if

your vehicle has one.

Allow the engine to run for at least

30 minutes, by driving or with the vehicle
stationary, so that the battery reaches an
adequate state of charge.

Starting using another battery

Some functions, including Stop & Start,
are not available if the battery is not
sufficiently charged.

Raise the plastic cover on the (+) terminal,

if your vehicle has one.

Connect the red cable to the positive

terminal (+) of the flat battery A (at the metal
elbow) then to the positive terminal (+) of the
slave battery B

or the booster.

Connect one end of the green or black

cable to the negative terminal (-) of the
slave battery B or the booster (or earth
point on the other vehicle).

Connect the other end of the green or black

cable to the earth point C

on the broken

down vehicle.

Never try to start the engine by
connecting a battery charger.
Never use a 24 V or higher battery
booster.
First check that the slave battery has a
nominal voltage of 12 V and a capacity
at least equal to that of the discharged
battery.
The two vehicles must not be in contact
with each other.
Switch off the electrical consumers on
both vehicles (audio system, wipers,
lighting, ...).
Ensure that the jump lead cables do
not pass close to moving parts of the
engine (cooling fan, belts, ...).
Do not disconnect the (+) terminal when
the engine is running.

When your vehicle's battery is discharged, the
engine can be started using a slave battery
(external or on another vehicle) and jump lead
cables or a battery booster.

320

In the event of a breakdown

C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016

Never try to charge a frozen battery.
If the battery has been frozen, have
it checked by a CITROËN dealer or a
qualified workshop, who will check that
the internal components have not been
damaged and the casing is not cracked,
which could cause a leak of toxic and
corrosive acid.

Switch off the ignition.

Switch off all electrical consumers (audio

system, lighting, wipers, ...).

Switch off the charger B before connecting

the cables to the battery, so as to avoid any
dangerous sparks.

Ensure that the charger cables are in good

condition.

F Raise the plastic cover, if your vehicle has

one, on the (+) terminal.

Connect the charger B cables as follows:

- the positive (+) red cable to the (+)

terminal of the battery A,

- the negative (-) black cable to the earth

point C

on the vehicle.

At the end of the charging operation, switch

off the charger B before disconnecting the
cables from the battery A.

It is not necessary to disconnect the
battery.

If you envisage charging your vehicle's
battery yourself, use only a charger
compatible with lead-acid batteries of a
nominal voltage of 12 V.

Follow the instructions for use provided
by the manufacturer of the charger.
Never reverse polarities.

Charging the battery using a battery charger

If this label is present, it is essential
to use only a 12 V charger, to avoid
causing irreversible damage to the
electrical components related to the
Stop & Start system.

For optimum service life of the battery, it is
essential to maintain an adequate state of
charge.
In some circumstances it may be necessary to
charge the battery:
-

if you use your vehicle essentially for short
journeys,

- if the vehicle is to be taken off the road for

several weeks.

Contact a CITROËN dealer or a qualified
workshop.

321

In the event of a breakdown

C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016

The Stop & Start system may not be
operational during the trip following the
first engine start.
In this case, the system will only be
available again after a continuous
period of immobilisation of the vehicle,
a period which depends on the ambient
temperature and the state of charge of
the battery (up to about 8 hours).

Do not force the lever as locking will
not be possible if the clamp is not
positioned correctly; start the procedure
again.

Disconnecting the (+) terminal
F Raise the lever A fully to release the

clamp B.

Remove the clamp B by lifting it off.

Reconnecting the (+) terminal
F Raise the lever A

fully.

Refit the open clamp B on the (+) terminal.

Push the clamp B fully down.

Lower the lever A to lock the clamp B.

Disconnecting the battery

In order to maintain an adequate state
of charge for starting the engine, it is
recommended that the battery be disconnected
if the vehicle is taken out of service for a long
period.
Before disconnecting the battery:
F

close all openings (doors, boot, windows,

roof),

switch off all electrical consumers (audio

system, wipers, lighting, ...),

switch off the ignition and wait for four

minutes.

At the battery, detach just the (+) terminal.

Following reconnection of the battery

Following reconnection of the battery, switch on
the ignition and wait 1 minute before starting to
permit initialisation of the electronic systems.
However, if problems remain following this
operation, contact a CITROËN dealer or a
qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise (depending on
version):
- the remote control key,
- the electric blind(s),
- ...

Quick-release terminal clamp

322

In the event of a breakdown

C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016

Towing

The towing eye is installed in the boot under
the floor.
The front protective cover opening tool is fixed
on the towing eye.
To gain access to it:
F open the boot,
F

lift the floor and remove it,

remove the towing eye from its housing.

General recommendations

Observe the legislation in force in your country.
Ensure that the weight of the towing vehicle is higher than that of the towed vehicle.
The driver must remain at the wheel of the towed vehicle and must have a valid driving licence.
When towing a vehicle with all four wheels on the ground, always use an approved towing
arm; rope and straps are prohibited.
The towing vehicle must move off gently.
When towing a vehicle with the engine off, there is no longer any power assistance for
braking or steering.
In the following cases, you must always call on a professional recovery service:
- vehicle broken down on a motorway or fast road,
- four-wheel drive vehicle,
- when it is not possible to put the gearbox into neutral, unlock the steering, or release

the parking brake,

- towing with only two wheels on the ground,
- where there is no approved towing arm available...

Procedure for having your vehicle towed or for towing another vehicle using the towing eye.

Access to the tools

323

In the event of a breakdown

C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016

Towing another vehicle

On the rear bumper, unclip the cover by

pressing at the bottom.

Screw the towing eye in fully.

Install the towing bar.

Switch on the hazard warning lamps on

both vehicles.

Move off gently, drive slowly and for a short

distance.

On the front bumper, unclip the cover using

the tool fixed on the towing eye.

Screw the towing eye in fully.

Install the towing bar.

Place the gear lever in neutral (position N

with an automatic gearbox).

Towing your vehicle

Failure to observe this instruction could
result in damage to certain components
(braking, transmission, etc.) and the
absence of braking assistance the next
time the engine is started.

Unlock the steering by turning the key

in the ignition one notch and release the
parking brake.

Switch on the hazard warning lamps on

both vehicles.

Move off gently, drive slowly and for a short

distance.

324

In the event of a breakdown

C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016

Running out of fuel (Diesel)

On vehicles fitted with Diesel engines, the fuel
system must be primed if you run out of fuel.
For all versions other than BlueHDi, refer to the
corresponding engine compartment view.

Other HDi engines

(except BlueHDi version)

For more information on Diesel misfuel
prevention

, refer to the corresponding

section.

If the engine does not start first time,
don't keep trying but start the procedure
again from the beginning.

BlueHDi engines

Fill the fuel tank with at least five litres of

Diesel.

Switch on the ignition (without starting the

engine).

Wait around 6 seconds and switch off the

ignition.

Repeat the operation 10 times.

Operate the starter to run the engine.

Add at least five litres of Diesel fuel to the

tank.

Open the bonnet.

If necessary, unclip the styling cover for

access to the priming pump.

Squeeze and release the priming pump

repeatedly until resistance is felt (there
may be resistance at the first press).

Operate the starter to start the engine

(if the engine does not start at the first
attempt, wait around 15 seconds before
trying again).

If the engine does not start after a

few attempts, operate the priming pump
again then start the engine.

Refit the styling cover and clip it in place.

Close the bonnet.

325

Technical data

C4-Picasso-II_en_Chap09_caracteristiques-techniques_ed02-2016

Petrol engine

PureTech 110 S&S

PureTech 130 S&S

Gearbox

Manual (6-speed)

EAT6 automatic (6-speed)

Model code

3D... 3E... 3A...

HNX...

M/1S - M/2SM

HNY…

M/1S - M/2SM

HNY…

T/1S - T/2S

Cubic capacity (cc)

1 199

Bore x stroke (mm)

75 x 90.5

Max power*: EU standard (kW)

Max power engine speed (rpm)

5 500

Max torque: EU standard (Nm)

230

Max torque engine speed (rpm)

1 750

Fuel

Unleaded

Catalytic converter

yes

Engine oil capacity (in litres) (with filter
replacement)

4.25

Petrol engines and gearboxes

3D...:

CITROËN C4 Picasso (5-seat).

3A...:

CITROËN Grand C4 Picasso (7-seat).

3E...:

CITROËN Grand C4 Picasso (5-seat).

* The maximum power corresponds to the value type-approved on a test bed, under conditions defined in European legislation (Directive 1999/99/EC).

326

Technical data

C4-Picasso-II_en_Chap09_caracteristiques-techniques_ed02-2016

3D...:

CITROËN C4 Picasso (5-seat).

3A...:

CITROËN Grand C4 Picasso (7-seat).

3E...:

CITROËN Grand C4 Picasso (5-seat).

* The maximum power corresponds to the value type-approved on a test bed, under conditions defined in European legislation (Directive 1999/99/EC).
** For Israel.

Petrol engine

THP 150 / 160

THP 165 S&S

THP 165 S&S

Gearbox

EAT6 automatic (6-speed)

Model code

3D... 3E... 3A...

5GX - 5GY...

A-A/1-A/2-A/D- A/1D- A/2D-

Y-Y/1-Y/2

5GZT/S

5GY...

A/S - A/1S - A/2S

Cubic capacity (cc)

1 598

Bore x stroke (mm)

77 x 85.8

Max power*: EU standard (kW)

110 / 121

121

Max power engine speed (rpm)

6 000

Max torque: EU standard (Nm)

240

Max torque engine speed (rpm)

1 400

Fuel

Unleaded

Catalytic converter

yes

Engine oil capacity (in litres) (with filter
replacement)

4.25

327

Technical data

C4-Picasso-II_en_Chap09_caracteristiques-techniques_ed02-2016

* The weight values are calculated with a towbar.

** The kerb weight is equal to the unladen weight + driver (75 kg).

*** The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount; warning,

towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.

Petrol engine

PureTech 110 S&S*

PureTech 130 S&S*

Gearbox

Manual (6-speed)

EAT6 automatic (6-speed)

Model code

3D... 3E... 3A...

HNX...

M/1S - M/2SM

HNY…

M/1S - M/2SM

HNY…

T/1S - T/2S

Unladen weight

1 280

1 280 - 1 295 - 1 297

1 298 - 1 315 - 1 317

Kerb weight**

1 355

1 355 - 1 370 - 1 372

1 373 - 1 390 - 1 392

Gross vehicle weight (GVW)

1 905

1 905 - 2 075 - 2 125

1 918 -1 957 - 2 136

Gross train weight (GTW)
on a 12% gradient

3 035

3 175 - 3 125 - 3 175

3 188 - 3 007 - 3 186

Braked trailer (within the GTW limit)
on a 10% or 12% gradient

1 130

1 270 - 1 050 - 1 050

Braked trailer*** (with load transfer within the
GTW limit)

1 330

1 470 - 1 350 - 1 350

Unbraked trailer

640

640 - 647 - 648

Recommended nose weight

Petrol weights and towed loads (in kg)

The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for

each additional 1 000 metres of altitude.

When towing, the speed must never exceed 60 mph (100 km/h) (comply with the legislation in force in your country).

High exterior temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the exterior temperature is above 37 °C,

limit the towed load.

328

Technical data

C4-Picasso-II_en_Chap09_caracteristiques-techniques_ed02-2016

The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount; warning,

towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.

When towing, the speed must never exceed 60 mph (100 km/h) (comply with the legislation in force in your country).

High exterior temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the exterior temperature is above 37 °C,

limit the towed load.

Petrol engine

THP 150 / 160

THP 165 S&S

***

Gearbox

EAT6 automatic (6-speed)

Model code

3D... 3E... 3A...

5GX - 5GY...

A-A/1-A/2-A/D- A/1D- A/2D-

Y-Y/1-Y/2

5GZT/S

5GY...

A/S - A/1S - A/2S

Unladen weight

1 405 - 1 428 - 1 430

1 310 - 1 318 - 1 320

1 390 - 1 425 - 1 425

Kerb weight*

1 480 - 1 503 - 1 505

1 385- 1 393 - 1 395

1 465 - 1 500 - 1 500

Gross vehicle weight (GVW)

1 940 - 2 140 - 2 160

1 930 - 2 100 - 2 150

Gross train weight (GTW)
on a 12% gradient

2 740 - 2 940 - 2 960

3 330 - 3 350 - 3 350

Braked trailer (within the GTW limit)
on a 10% or 12% gradient

800

1 400 - 1 250 - 1 200

Braked trailer** (with load transfer within the
GTW limit)

800

1 600 - 1 550 - 1 500

Unbraked trailer

600

685 - 690 - 690

Recommended nose weight

* The kerb weight is equal to the unladen weight + driver (75 kg).

** The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount; warning,

towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.

*** For Israel.

329

Technical data

C4-Picasso-II_en_Chap09_caracteristiques-techniques_ed02-2016

Diesel engines and gearboxes

.../S: e-HDi model fitted with Stop & Start.
3D...:

CITROËN C4 Picasso (5-seat).

3E...:

CITROËN Grand C4 Picasso (5-seat).

3A...:

CITROËN Grand C4 Picasso (7-seat).

Diesel engine

HDi 115

BlueHDi 100 S&S

Gearbox

Manual (6-speed)

Model code

3D... 3E... 3A...

9HC...
8 - 8/1

BHY...

6/1S - 6/2SM

Cubic capacity (cc)

1 560

Bore x stroke (mm)

75 x 88.3

Max power*: EU standard (kW)

Max power engine speed (rpm)

3 600

3 750

Max torque: EU standard (Nm)

270

254

Max torque engine speed (rpm)

1 750

Fuel

Diesel

Catalytic converter

yes

Particle filter

yes

Engine oil capacity, with filter replacement
(in litres)

3.75

* The maximum power corresponds to the value type-approved on a test bed, under conditions defined in European legislation (Directive 1999/99/EC).

330

Technical data

C4-Picasso-II_en_Chap09_caracteristiques-techniques_ed02-2016

Diesel engines and gearboxes

.../S: e-HDi model fitted with Stop & Start.
3D...:

CITROËN C4 Picasso (5-seat).

3E...:

CITROËN Grand C4 Picasso (5-seat).

3A...:

CITROËN Grand C4 Picasso (7-seat).

Diesel engine

BlueHDi 115/120 S&S

BlueHDi 135/150 S&S

Gearbox

Manual (6-speed)

EAT6 automatic

(6-speed)

Manual (6-speed)

EAT6 automatic

(6-speed)

Model code

3D... 3E... 3A...

BHZ - BHX...

M/S - M/1S

BHZ - BHX...

T/1S - T/2S

AHX-AHR-AHV-AHS...

M/S - M/1S

AHX...

T/S - T/1S

Cubic capacity (cc)

1 560

1 997

Bore x stroke (mm)

75 x 88.3

85 x 88

Max power*: EU standard (kW)

85 / 88

110

Max power engine speed (rpm)

3 500

3 750

Max torque: EU standard (Nm)

300

370

Max torque engine speed (rpm)

1 750

Fuel

Diesel

Catalytic converter

yes

Particle filter

yes

Engine oil capacity, with filter replacement
(in litres)

3.75

6.1

* The maximum power corresponds to the value type-approved on a test bed, under conditions defined in European legislation (Directive 1999/99/EC).

331

Technical data

C4-Picasso-II_en_Chap09_caracteristiques-techniques_ed02-2016

Diesel weights and towed loads (in kg)

The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for

each additional 1 000 metres of altitude.

When towing, the speed must never exceed 60 mph (100 km/h) (comply with the legislation in force in your country).

High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the ambient temperature is above 37 °C,

limit the towed load.

Diesel engine

HDi 115

BlueHDi 100 S&S*

Gearbox

Manual (6-speed)

Model code

3D... 3E... 3A...

9HC8

9HC8/1

BHY...

6/1S - 6/2SM

Unladen weight

1290 - 1 310 - 1 312

1 298 - 1 318 - 1 320

1 296 - 1 318 - 1 320

Kerb weight**

1 365 - 1 385 - 1 387

1 373 - 1 393 - 1 395

1 371 - 1 393 - 1 395

Gross vehicle weight (GVW)

1 940 - 2 110 - 2 150

1 950 - 2 120 - 2 175

Gross train weight (GTW)
on a 12% gradient

3 340 - 3 350 - 3 350

2 740 - 2 910 - 2 950

3 150 - 3 120 - 3 175

Braked trailer (within the GTW limit)
on a 10% or 12% gradient

1 400 - 1240 - 1 200

800

1 200 - 1 000 - 1 000

Brakes trailer***
(with load transfer within the GTW limit)

1 600 - 1 540 - 1 500

800

1 400 - 1 300 - 1 300

Unbraked trailer

680 - 690 - 690

685 - 695 - 695

645 - 659 - 660

Recommended nose weight

* The weights are calculated with a towbar fitted.

** The kerb weight is equal to the unladen weight + driver (75 kg).

*** The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount; warning,

towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.

332

Technical data

C4-Picasso-II_en_Chap09_caracteristiques-techniques_ed02-2016

Diesel weights and towed loads (in kg)

* The kerb weight is equal to the unladen weight + driver (75 kg).

** The weight of the braked trailer can be increased, within the GTW limit, if the GVW of the towing vehicle is reduced by an equal amount; warning,

towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.

The GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for

each additional 1 000 metres of altitude.

When towing, the speed must never exceed 60 mph (100 km/h) (comply with the legislation in force in your country).

High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the ambient temperature is above 37 °C,

limit the towed load.

Diesel engine

BlueHDi 115/120 S&S

BlueHDi 135/150 S&S

Gearbox

Manual (6-speed)

EAT6 automatic

(6-speed)

Manual (6-speed)

EAT6 automatic

(6-speed)

Model code

3D... 3E... 3A...

BHZ - BHX...

M/S - M/1S

BHZ - BHX...

T/1S - T/2S

AHX-AHR-AHV-

AHS...

M/S - M/1S

AHX...

T/S - T/1S

Unladen weight

1 320 - 1 345 - 1347

1 320 - 1 357 - 1 359

1 415 - 1 428 - 1 430

1 435 - 1 474 - 1 476

Kerb weight*

1 395 - 1 420 - 1 422

1 395 - 1 432 - 1 434

1 490 - 1 503 - 1 505

1 510 - 1 549 - 1 551

Gross vehicle weight (GVW)

1 950 - 2 100 - 2 175

1 975 - 2 025 - 2 205

2 030 - 2 200 - 2 250

2 030 - 2 200 - 2 280

Gross train weight (MTRA)
on a 12% gradient

3 350 - 3 350 - 3 375

3 375 - 3 225 - 3 405

3 530 - 3 560 - 3 650

3 530 - 3 580 - 3 580

Braked trailer (within GTW limit)
on a 10% or 12% gradient

1 400 - 1 250 - 1 200

1 400 - 1 200 - 1 200

1 500 - 1 450 - 1 400

1 500 - 1 380 - 1 300

Braked trailer**
(with load transfer within the GTW limit)

1 600 - 1 550 - 1 500

1 600 - 1 500 - 1 500

1 700 - 1 750 - 1 700

1 700 - 1 680 - 1 600

Unbraked trailer

660 - 672 - 674

660 - 675 - 675

745 - 750 - 750

750

Recommended nose weight

333

Technical data

C4-Picasso-II_en_Chap09_caracteristiques-techniques_ed02-2016

Dimensions (in mm)

These dimensions have been measured on an unladen vehicle.

* Mirrors folded.

334

Technical data

C4-Picasso-II_en_Chap09_caracteristiques-techniques_ed02-2016

Identification markings

Various visible markings for the identification of your vehicle.

A. Vehicle Identification Number (VIN)

under the bonnet.

This number is engraved on the chassis
near the right-hand front wheel arch.

The tyre pressures must be checked
when the tyres are cold, at least once
a month.

If the tyre pressures are too low, this
increases fuel consumption.

C. Manufacturer's label.

This self-destroying label on the middle
door pillar, right or left-hand side, contains
the following information:
- the manufacturer's name,
-

the European whole vehicle type approval number,

- the vehicle identification number (VIN),
- the maximum authorised weight (gross

vehicle weight),

- the maximum authorised weight with

trailer (gross train weight),

- the maximum front axle weight,
- the maximum rear axle weight.

D. Tyre/paint label.

This label on the middle door pillar, driver's
side, contains the following information:
- the tyre inflation pressures, laden and

unladen,

- the tyre sizes (including the tyre load

index and speed rating),

- the inflation pressure for the spare

wheel,

- the paint colour code.

B. Vehicle Identification Number (VIN) on

the windscreen lower cross member.

This number is indicated on a self-
adhesive label which is visible through the
windscreen.

The original tyres fitted to the vehicle
may have a load index or speed rating
higher than those given on the label;
this has no effect on the inflation
pressures.

Была ли эта страница вам полезна?

Да!Нет

2 посетителя считают эту страницу полезной.

Citroen C4 Picasso (2017 year). Manual — part 21

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.