Citroen Jumpy (2016 year). Manual — part 20
303
8
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Changing a bulb
Halogen bulb: turn the bulb anti-clockwise.
Type A
Bayonet bulb: press on the bulb then turn it
anticlockwise.
Type B
Type C
Type D
All glass bulb: pull gently as it is fitted by
pressure.
Halogen bulb: release the retaining spring from
its housing.
Halogen bulbs must be changed after
the headlamp has been off for several
minutes (risk of serious burns). Do not
touch the bulb directly with your fingers,
use lint-free cloths.
When each operation has been completed,
check the operation of the lighting.
Types of bulb
Various types of bulb are fitted to your vehicle.
To remove them:
Xenon bulb: xenon bulbs must be changed by
a CITROËN dealer or a qualified workshop as
there is a risk of electrocution.
Type E
304
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Front lamps
Xenon headlamps
For more information on Changing a bulb
and in particular the types of bulb, refer to the
corresponding section.
Halogen headlamps
For more information on Changing a bulb
and in particular the types of bulb, refer to the
corresponding section.
For H7 type bulbs with lugs... take care
to observe their correct installation
so as to ensure the best lighting
performance.
Front fog lamps
Type D
, H11-55W
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal surface of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.
1.
Main beam headlamps.
Type C
, H1-55W.
2.
Dipped beam headlamps.
Type E
, D8S 25W
3.
Direction indicators.
Type B,
PY21W-21W (amber)
1.
Sidelamps.
Type A
, W5W-5W.
2.
Main beam headlamps.
Type C
, H1-55W
3.
Dipped beam headlamps.
Type C
, H7-55W
4.
Daytime running lamps.
Type A, W21W LL-21W
5.
Direction indicators.
Type B
, PY21W-21W (amber)
305
8
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Direction indicator side
repeater
Type A
, WY5W-5W (amber)
Daytime running lamps / sidelamps
If fitted to your vehicle, contact a CITROËN
dealer or a qualified workshop for the
replacement of this type of LED lamp and light
guide.
A replacement kit for the LEDs is available from
CITROËN dealers.
The headlamps have polycarbonate
lenses with a protective coating:
F do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,
F
use a sponge and soapy water or a
pH neutral product,
F
when using a high pressure washer
on persistent marks, do not keep
the lance directed towards the
lamps or their edges for too long,
so as not to damage their protective
coating and seals.
Changing a bulb should only be done
after the headlamp has been switched
off for several minutes (risk of serious
burns).
F Do not touch the bulb directly with
your fingers, use a lint-free cloth.
It is imperative to use only anti-
ultraviolet (UV) type bulbs to avoid
damaging the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specification.
-
Push the repeater towards the rear and
disengage it.
- When refitting, engage the repeater
towards the front and then bring it towards
the rear.
Amber coloured bulbs (direction indicators and
side repeaters) must be replaced with bulbs of
identical specification and colour.
306
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
When refitting the connector and bulb
in the lamp, push the assembly into its
housing until it clicks into place.
Dipped beam headlamps
(halogen headamps)
Type C
, H7-55W
Daytime running lamps
(halogen headlamps)
Type A, W21W LL-21W
Sidelamps
(halogen headlamps)
Type A
, W5W
F Press the upper clip on the cover then tip it
rearwards to remove it.
F Press the lower clip on the electrical
connector and remove the assembly of
connector and bulb.
F
Pull the bulb out and change it.
To refit, carry out these operations in reverse
order.
F Press the upper clip on the cover then tip it
rearwards to remove it.
F Press the two side clips on the electrical
connector and remove the assembly of
connector and bulb.
F
Pull out the bulb and change it.
To refit, carry out these operations in reverse
order.
F Press the upper clip on the cover then tip it
rearwards to remove it.
F Press the two side clips on the electrical
connector and remove the assembly of
connector and bulb.
F
Pull the bulb out and change it.
To refit, carry out these operations in reverse
order.
307
8
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Be aware that the area behind the right-
hand headlamp (facing forwards) may
be hot, with the risk of burns (overflow
pipe).
Faster flashing of a direction indicator
warning lamp (left or right) indicates a
failed bulb on that side.
Direction indicators
(halogen headlamps)
Type B
, PY21W-21W (amber)
Main beam headlamps
(halogen headlamps)
Type C
, H1-55W
F Press the upper clip on the cover then tip it
rearwards to remove it.
F Press the lower clip on the electrical
connector and remove the assembly of
connector and bulb.
F
Pull the bulb out and change it.
To refit, carry out these operations in reverse
order.
F Press the upper clip on the cover then tip it
rearwards to remove it.
F Turn the bulb holder a quarter turn anti-
clockwise.
F
Remove the bulb holder.
F
Change the failed bulb.
To refit, carry out these operations in reverse
order.
308
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Dipped beam headlamps
(xenon headlamps)
Type E
, D8S 25W
F Press the upper clip on the cover then tip it
rearwards to remove it.
F Turn the bulb holder a quarter turn
anti-clockwise.
F
Change the failed bulb.
To refit, carry out these operations in reverse
order.
Replacement of D8S xenon bulbs must
be done by a CITROËN dealer or a
qualified workshop as there is a risk of
electrocution.
It is recommended that both D8S bulbs
be replaced at the same time, in the
event of the failure of one of them.
Main beam headlamps
(xenon headlamps)
Type C
, H1-55W
When refitting the connector and bulb
in the lamp, push the assembly into its
housing until it clicks into place.
Faster flashing of a direction indicator
warning lamp (left or right) indicates a
failed bulb on that side.
Direction indicators
(xenon headlamps)
Type B
, PY21W-21W (amber)
F Press the upper clip on the cover then tip it
rearwards to remove it.
F Press the lower clip on the electrical
connector and remove the assembly of
connector and bulb.
F
Pull the bulb out and change it.
To refit, carry out these operations in reverse
order.
309
8
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Front foglamps
Type C
, H11-55W
F
Press the locking clip and disconnect the
connector.
F Turn the bulb holder a quarter turn
anti-clockwise.
F
Remove the bulb holder.
F
Change the failed bulb.
To refit, carry out these operations in reverse
order.
You can also go to a CITROËN
dealer or a qualified workshop for the
replacement of these bulbs.
F
Below the front bumper, unscrew the fixing
screws for the deflector A
.
F Remove the deflector A
.
310
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Rear lamps
(side-hinged rear doors)
For more information on Changing a bulb and
in particular, the types of bulbs, refer to the
corresponding section.
F
While holding the lamp in place, press the
clip on the inside then carefully remove the
lamp.
F
Disconnect the electrical connector.
For vehicles with interior trim, contact
a CITROËN dealer or a qualified
workshop to have the work done.
1.
Brake lamps / sidelamps.
Type B
, P21/5W-21/5W
2.
Direction indicators.
Type B
, PY21W-21W (amber)
3.
Reversing lamps.
Type B, P21W-21W
4.
Foglamps / sidelamps.
Type B
, P21/4W-21/4W
F Identify the failed bulb then open the rear
doors.
F
Spread the three lugs slightly, then extract
the bulb holder.
F
Remove the failed bulb by pressing
lightly on it, then turning it a quarter turn
clockwise.
F
Change the bulb.
To reassemble, carry out these operations in
reverse order.
F
From inside, remove the ventilation grille, if
your vehicle has one.
F
From outside, unscrew the two lamp fixing
screws.
311
8
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Number plate lamps
(side-hinged doors)
Type A
, W5W-5W
F
Remove the plastic cover using a small
screwdriver.
F
Using a screwdriver through the aperture,
push the lamp towards the outside.
F
Disconnect the electrical connector.
F
Remove the lamp.
F Turn the bulb holder a quarter turn anti-
clockwise.
F
Change the failed bulb.
To refit, press on the lamp to clip it in place.
Third brake lamp
(side-hinged doors)
Type A
, W5W-5W
To refit, press on the lens to clip it in place.
F
Open the left hand rear door.
F Insert a thin screwdriver into one of the cut-
outs in the lens.
F
Push it outwards to unclip it.
F
Remove the lens.
F
Change the failed bulb.
312
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Courtesy lamps
(front and rear)
Type A
, W5W-5W
F
Unclip the lens by inserting a thin
screwdriver into the cut-outs at each side
of the lamp.
F
Pull the bulb out and change it.
F Clip the lens in place and ensure that it is
secure.
313
8
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Rear lamps
(tailgate)
For more information on Changing a bulb and
in particular, the types of bulbs, refer to the
corresponding section.
F
While holding the lamp in place, press the
clip on the inside then carefully remove the
lamp.
F
Disconnect the electrical connector.
F
Identify the failed bulb then open the boot.
For vehicles with interior trim, contact
a CITROËN dealer or a qualified
workshop to have the work done.
1.
Brake lamps / sidelamps.
Type B
, P21/5W-21/5W
2.
Direction indicators.
Type B
, PY21W-21W (amber)
3.
Reversing lamps.
Type B, P21W-21W
4.
Foglamps / sidelamps.
Type B
, P21/4W-21/4W
F From inside, remove the cover, if your
vehicle has one.
F From the outside, press on the inner clips
on the plastic finisher then tip it towards the
outside to remove it.
F
Unscrew the two lamp fixing screws.
F
Spread the three lugs slightly, then extract
the bulb holder.
F
Remove the failed bulb by pressing
lightly on it, then turning it a quarter turn
clockwise.
F
Change the bulb.
To reassemble, carry out these operations in
reverse order.
314
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
To refit, press on the lens to clip it in place.
F
Unclip the trim at each end by turning it
upwards.
F
Pull on the trim to disengage the central
clips, then remove it.
F
Using a screwdriver through the aperture,
push the lamp towards the outside.
F
Disconnect the electrical connector.
F
Remove the lamp.
F Turn the bulb holder a quarter turn anti-
clockwise.
F
Change the failed bulb.
To refit, carry out these operations in reverse
order.
To refit the lamp and trim, press on them to clip
them in place.
Third brake lamp
(tailgate)
Type A
, W5W-5W
Number plate lamps
(tailgate)
Type A
, W5W-5W
F
Open the tailgate.
F Insert a thin screwdriver into one of the cut-
outs in the lens.
F
Push it outwards to unclip it.
F
Remove the lens.
F
Change the failed bulb.
315
8
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Courtesy lamps
(front and rear)
For the replacement of this type of LED lamp
and light guide, contact a CITROËN dealer or a
qualified workshop.
A replacement kit for the LEDs is available from
CITROËN dealers.
Rear lamps
For more information on Changing a bulb and
in particular, the types of bulbs, refer to the
corresponding section.
Platform cab
F
Identify the failed bulb.
F
Remove the four screws securing the lens.
F
Pull the lens towards you.
F
Remove the failed bulb by pressing lightly
on it and then turning it a quarter turn
clockwise.
F
Change the bulb.
1.
Direction indicators.
Type B, P21W-21W
2.
Brake lamps.
Type B, P21W-21W
3.
Sidelamps.
Type B, R10W-10W
4.
Reversing lamps.
Type B, P21W-21W
5.
Foglamps.
Type B, P21W-21W
To reassemble, carry out these operations in
reverse order.
316
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
F
Unclip the cover by pulling at the top left, then
right.
F
Disengage the cover completely and turn it over,
Good
Failed
Tweezer
Access to the tools
F
Take the tweezer from its housing.
The extraction tweezer is located behind the
fusebox cover, on the dashboard pillar.
Before changing a fuse:
F the cause of the failure must be identified
and rectified,
F all electrical consumers must be
switched off,
F the vehicle must be immobilised with the
ignition off,
F
identify the failed fuse using the tables and
layout drawings in the following pages.
Changing a fuse
To replace a fuse, you must:
F use the special tweezer to extract the fuse
from its housing and check the condition of
its filament.
F always replace the failed fuse with a fuse
of the same rating (same colour); using
a different rating could cause faults (risk
of fire).
If the fuse fails again soon after replacement,
have the vehicle's electrical system checked by
a CITROËN dealer or a qualified workshop.
The replacement of a fuse not shown in
the tables below may cause a serious
malfunction of your vehicle. Contact
a CITROËN dealer or a qualified
workshop.
Changing a fuse
317
8
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
CITROËN will not accept responsibility
for the cost incurred in repairing your
vehicle or for rectifying malfunctions
resulting from the installation of
accessories not supplied and not
recommended by CITROËN and
not installed in accordance with its
instructions, in particular when the
combined consumption of all of the
additional equipment connected
exceeds 10 milliamperes.
Installing electrical
accessories
Your vehicle's electrical system is
designed to operate with standard or
optional equipment.
Before installing other electrical
equipment or accessories on your
vehicle, contact a CITROËN dealer or a
qualified workshop.
For more information on installing a
towbar or equipment of the TAXI type,
contact a CITROËN dealer.
Dashboard fuses
The fusebox is placed in the lower dashboard
(left-hand side).
Access to the fuses
F
Unclip the cover by pulling at top left, then
right.
318
In the event of a breakdown
Jumpy_en_Chap08_En-cas-de-panne_ed01-2016
Fuse
N°
Rating
(A)
Functions
F1
10
Electric power steering, clutch switch
F4
15
Horn.
F5
20
Front/rear screenwash pump.
F6
20
Front/rear screenwash pump.
F7
10
Rear 12 V accessory socket.
F8
20
Single or double rear wipers.
F10/F11
30
Front and rear, exterior, interior locks.
F13
10
Front air conditioning controls, radio controls, gear lever,
head-up display.
F14
5
Alarm, emergency and assistance calls.
F17
5
Instrument panel.
F19
3
Steering mounted controls.
F21
3
"Keyless Entry and Starting" system or ignition switch.
F22
3
Rain and sunshine sensor, multifunction detection
camera.
F23
5
Seat belt unfastened or not fastened display screen.
F24
5
Touch screen, reversing camera and parking sensors.
F25
5
Airbags.
F29
20
Audio system, touch screen, CD player, navigation.
F31
15
Audio system (battery +).
F32
15
Front 12 V accessory socket.
F34
5
Blind spot monitoring system, door mirror electric
controls.
F35
5
Heated washer jets, headlamp beam height
control.
F36
5
Torch charger, rear courtesy lamp.
Version 1 (Eco)
The fuses described hereafter vary according
to the equipment in your vehicle.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст