Citroen DS4 (2017 year). Manual — part 6

Access

DS4_en_Chap02_ouvertures_ed01-2016

This system allows automatic simultaneous locking of the doors and boot as soon as the speed of
the vehicle exceeds 6 mph (10 km/h).

Anti-intrusion security

Operation

Activation / Deactivation

If one of the doors or the boot is open, the
automatic central locking does not take place.

Carrying long or
voluminous objects

If you want to drive with the boot open,
you should press the central locking
button to lock the doors. Otherwise,
every time the speed of the vehicle
exceeds 6 mph (10 km/h), the locks
will rebound and the alerts mentioned
above will appear.

Pressing the central locking button unlocks the
vehicle.
Above 6 mph (10 km/h), this unlocking is
temporary.

Driving with the doors locked may
render access for the emergency
services difficult in an emergency.

This is signalled by the sound of
the locks rebounding, accompanied
by illumination of this symbol in the
instrument panel, an audible signal
and the display of an alert message.

With the ignition on, press this button

until an audible signal starts and a
corresponding message is displayed.

The state of the system stays in memory when
switching off the ignition.

You can activate or deactivate this function
permanently.

Access

DS4_en_Chap02_ouvertures_ed01-2016

Doors

Opening

After unlocking the vehicle or with the

electronic key of the Keyless Entry and
Starting system in the recognition zone,
pull the door handle.

Pull the interior control lever of a front door;

this unlocks the vehicle completely.

Closing

- with the engine running or the

vehicle moving (speed below
6 mph (10 km/h)), this warning
lamp comes on, accompanied
by an alert message for a few
seconds.

- with the vehicle moving (speed above

6 mph (10 km/h)), in addition to the warning
lamp and alert message, there is an
audible signal for a few seconds.

When the selective unlocking is
activated, the first press of the remote
control unlocking button permits
unlocking of the driver's door only.

With the selective unlocking activated:
- opening the driver's door unlocks

the driver's door only (if the vehicle
has not already been completely
unlocked).

- opening the passenger's door

unlocks the rest of the vehicle.

The interior door controls do
not operate when the vehicle is
deadlocked.

From outside

From inside

When a door is not closed correctly:

Access

DS4_en_Chap02_ouvertures_ed01-2016

Boot

The vehicle or just the boot is unlocked,
depending on the setting.

Selective unlocking

By default, complete unlocking is activated.
This setting is done in the "Driving" menu,
then "Vehicle settings"

and "Vehicle

access"

When unlocking of the boot only is activated:
F

With the electronic key on your person and

in the recognition zone A, press the boot
unlocking control to unlock just the boot,
then raise the tailgate.

Use this button for access to
additional information.

Lower the tailgate using one of the interior

grab handles.

Closing

Opening

After unlocking the vehicle or the boot with

the Keyless Entry and Starting system
electronic key on your person in the
recognition zone A, press the boot opening
control then raise the tailgate.

If the boot is not closed correctly:

- with the engine running or the

vehicle moving (speed below
6 mph (10 km/h)), this warning
lamp comes on, accompanied by
the display of an alert message
for a few seconds.

- with the vehicle moving (speed above

6 mph (10 km/h)), in addition to the warning
lamp and alert message, there is an an
audible signal for a few seconds.

Unlocking is signalled by rapid flashing of the
direction indicators for a few seconds.

Complete unlocking

Access

DS4_en_Chap02_ouvertures_ed01-2016

To manually unlock the boot in the event of a
battery or central locking failure.

Back-up release

Fold back the rear seats to gain access to

the lock from inside the boot.

Insert a small screwdriver into hole A of the

lock to unlock the tailgate.

Move the latch to the left.

Locking after closing

If the fault persists after closing again, the boot
will remain locked.

Unlocking

Access

DS4_en_Chap02_ouvertures_ed01-2016

Alarm*

System which protects and provides a deterrent against theft and break-ins. It provides the following types of monitoring:

- exterior perimeter

The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot, the bonnet...

- interior volumetric

The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compartment or
moves inside the vehicle.

- tilt

The system checks for any change in the
attitude of the vehicle.
The alarm is triggered if the vehicle is lifted,
moved or knocked.

Self-protection function

The system checks for the putting out of
service of its components.
The alarm is triggered if the battery, the central
control or the siren wiring are put out of service
or damaged.

For all work on the alarm system,
contact a CITROËN dealer or a
qualified workshop.

* Depending on the country of sale.

Access

DS4_en_Chap02_ouvertures_ed01-2016

Locking the vehicle with full alarm system

Switch off the ignition and get out of the

vehicle.

Lock the vehicle with the remote control.

or
F

Lock the vehicle with the "Keyless Entry

and Starting" system.

The monitoring system is active: the indicator
lamp in the button flashes once per second
and the direction indicators come on for about
2 seconds.
Following an instruction to lock the vehicle,
the exterior perimeter monitoring is activated
after a delay of 5 seconds and the interior
volumetric and anti-tilt monitoring after a delay
of 45 seconds.

Deactivation

When the vehicle automatically locks
itself again (as happens if a door or
boot is not opened within 30 seconds of
unlocking), the monitoring system is not
reactivated automatically. To reactivate
the system, it is necessary to unlock
the vehicle and then lock it again using
the remote control or the "Keyless
Entry and Starting" system.

If an opening (door, boot...) is not closed
fully, the vehicle is not locked but the exterior
perimeter monitoring will be activated after a
delay of 45 seconds at the same time as the
interior volumetric and anti-tilt monitoring.

Activation

Press the unlocking button on the remote

control.

or
F

Unlock the vehicle with the "Keyless Entry

and Starting" system.

The monitoring system is deactivated: the
indicator lamp in the button goes off and the
direction indicators flash for about 2 seconds.

Access

DS4_en_Chap02_ouvertures_ed01-2016

Deactivate the interior volumetric and anti-tilt
monitoring to avoid unwanted triggering of the
alarm in certain cases such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transport by sea.

Locking the vehicle with exterior perimeter monitoring only

Switch off the ignition and within

ten seconds, press the button until the
indicator lamp is on continuously.

Get out of the vehicle.

Immediately lock the vehicle using the

remote control or the Keyless Entry and
Starting system.

The exterior perimeter monitoring alone is
activated: the indicator lamp in the button
flashes once per second.

To be effective, this deactivation must
be carried out each time the ignition is
switched off.

Reactivating the interior volumetric

and anti-tilt monitoring

Deactivate the perimeter monitoring by

unlocking the vehicle with the remote
control or the Keyless Entry and Starting
system.

The indicator lamp in the button goes off.

Reactivate all monitoring by locking the

vehicle with the remote control or the
Keyless Entry and Starting system.

The indicator lamp in the button flashes
once per second again.

Deactivating the interior volumetric

and anti-tilt monitoring

Access

DS4_en_Chap02_ouvertures_ed01-2016

Triggering of the alarm

This is indicated by sounding of the siren
and flashing of the direction indicators for
thirty seconds.
The monitoring functions remain active until
the alarm has been triggered eleven times in
succession.
When the vehicle is unlocked using the remote
control or the Keyless Entry and Starting
system, rapid flashing of the indicator lamp
in the button informs you that the alarm was
triggered during your absence. When the
ignition is switched on, this flashing stops
immediately.

Failure of the remote control

To deactivate the monitoring functions:

Locking the vehicle without

activating the alarm

Lock or deadlock the vehicle using the

key (integral to the remote control) in the
driver's door lock.

unlock the vehicle using the key (integral to

the remote control) in the driver's door lock,

open the door; the alarm is triggered,

switch on the ignition; the alarm stops; the

indicator lamp in the button goes off.

Operating fault

When the ignition is switched on, fixed
illumination of the indicator lamp in the button
indicates a fault with the system.
Have it checked by a CITROËN dealer or a
qualified workshop.

Access

DS4_en_Chap02_ouvertures_ed01-2016

Left hand front window control.

Right hand front electric window control.

The electric window controls remain
operational for approximately
45 seconds after the ignition is
switched off or until the vehicle is
locked after a door is opened.
If the passenger 's window cannot be
operated from the driver's door control
panel, carry out the operation from the
passenger's door control panel, and
vice versa.

Electric windows

Fitted with a safety anti-pinch system.

One-touch electric windows

Manual mode

After approximately ten consecutive
complete opening/closing movements
of the window, a protection function is
activated which only authorises closing
of the window to prevent damage to the
electric window motor.
Once the window is closed, the controls
will become available again after
approximately 40 minutes.

Press or pull the control firmly.

The window opens or closes fully
when the control is released.

Pressing the control again stops

the movement of the window.

Automatic mode

Press or pull the control gently.

The window stops when the
control is released.

Access

DS4_en_Chap02_ouvertures_ed01-2016

Safety anti-pinch

When the window rises and meets an obstacle,
it stops and partially lowers again.

Reinitialisation

If a window does not rise automatically, its
operation must be reinitialised.
F

Pull the control until the window stops.

Release the control and pull it again until

the window closes fully.

Continue to hold the control for

approximately one second after the window
has closed.

Press the control to lower the window

automatically to the low position.

When the window has reached the low

position, press the control again for
approximately one second.

The safety anti-pinch function is not
operational during these operations.

If the window cannot be closed (for
example, in the presence of ice), once
the window has lowered:
F

press and hold the control until the

window opens fully,

then pull the control immediately

and hold it until the window closes,

continue to hold the control for

approximately one second after the
window has closed.

The safety anti-pinch function is not
operational during these operations.

If an obstacle is encountered during
operation of the electric windows, you
must reverse the movement of the
window. To do this, press the control
concerned.
When the driver operates the
passenger's electric window control,
they must ensure that nothing is
preventing the windows closing
correctly.
The driver must ensure that the
passengers use the electric windows
correctly.
Be particularly aware of children when
operating the windows.
Be aware of passengers and/or other
persons present when closing the
windows with the key or the "Keyless
Entry and Starting" system.
Always remove the key from the ignition
when leaving the vehicle, even for a
short time.

Access

DS4_en_Chap02_ouvertures_ed01-2016

DS4_en_Chap03_ergonomie-et-confort_ed01-2016

ERGONOMY AND COMFORT

DS4_en_Chap03_ergonomie-et-confort_ed01-2016

Ease of use and comfort

DS4_en_Chap03_ergonomie-et-confort_ed01-2016

Front seats

Manual adjustments

Raise the control and slide the seat

forwards or backwards.

Release the control to lock the position.

Pull the control upwards to raise or push

it downwards to lower, as many times as
necessary, to obtain the position required.

Turn the control knob to adjust the seat

backrest angle.

As a safety measure, seat adjustments should only be done when stationary.

Before moving the seat backwards, ensure that there is nothing that might prevent the full travel of the seat.
There is a risk of trapping or pinching passengers if present in the rear seats or jamming the seat if large objects are placed on the floor behind
the seat.

Forwards-backwards

Seat height

Seat backrest angle

Ease of use and comfort

DS4_en_Chap03_ergonomie-et-confort_ed01-2016

Driver's seat electric

adjustments

Push the control forwards or rearwards to

slide the seat.

Tilt the rear part of the control upwards or

downwards to obtain the required height.

Tilt the front part of the control upwards or

downwards to obtain the required angle.

Tilt the control forwards or rearwards to

adjust the angle of the seat backrest.

The electrical functions of the driver's seat are deactivated approximately one minute after
the ignition is switched off.
To reactivate them, switch on the ignition.

Forwards-backwards

Cushion height and angle

Seat backrest angle

Ease of use and comfort

DS4_en_Chap03_ergonomie-et-confort_ed01-2016

Additional adjustments

To raise a head restraint, pull it upwards.

To lower the head restraint, press the lug A

and the head restraint at the same time.

To adjust the angle of the head restraint, tilt

its lower part forwards or rearwards.

The head restraint is fitted with a frame
with notches which prevents it from
lowering; this is a safety device in case
of impact.
The adjustment is correct when the
upper edge of the head restraint is
level with the top of the head.

Removing a head restraint

To remove the head restraint, press the

lug A and pull the head restraint upwards.

To put the head restraint back in place,

engage the head restraint stems in the
openings keeping them in line with the seat
back and press the lug A at the same time.

Never drive with the head restraints
removed; they must be in place and
adjusted correctly.

Head restraint height and angle

Была ли эта страница вам полезна?

Да!Нет

3 посетителя считают эту страницу полезной.

Citroen DS4 (2017 year). Manual — part 6

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.