Citroen Berlingo First Dag (2010 year). Manual — part 3

35

COMFORT -

VENTILATION

1. Windscreen de-icing or

demisting vents.

2. Front window de-icing or

demisting vents.

3. Side vents.
4. Centre vents.
5. Air outlets to front footwells.

The air conditioning system does not
contain chlorine and does not present
any danger to the ozone layer.
Operate the air conditioning system
for 5 to 10 minutes, once or twice a
month, to keep it in perfect working
order.
The water created by the air condi-
tioning condensation is discharged
via an opening provided for this pur-
pose. Therefore, a puddle of water
may form underneath the vehicle
when stationary.
If the system does not produce
cold air, do not use it and contact a
CITROËN dealer.

De-icing the rear windows and
mirrors
With the engine running, pressing
the control de-ices the rear windows
and mirrors.
It switches off automatically after ap-
proximately twelve minutes.
Pressing the control again switch-
es the de-icing system on again for
twelve minutes.
It is possible to switch off the de-
icing by pressing the control before
the twelve minutes have elapsed.

Advice on operation

Select the air distribution most suited
to your requirements and the climatic
conditions.
Gradually adjust the temperature
setting for your comfort.
Position the air control in the ''Outside
Air'' position.
For perfectly even air distribution,
take care not to obstruct the exterior
air intake grille and the vents. Check

that the passenger compartment fi lter

is in good condition.
When the engine is cold, to prevent
too great a distribution of cold air, the
ventilation will increase to its opti-
mum level gradually.
In order to be effective, the air condi-
tioning ( A/C button), should only be
used with the windows closed.
If the interior temperature remains
very high following a prolonged period
parked in the sun, do not hesitate to
ventilate the passenger compartment
for a few minutes.

COMFORT

36 -

Intake of exterior air.

HEATING

Turn the control from posi-
tion 1 to position 4 to obtain

an air fl ow suffi cient to en-

sure your comfort.

2. Air fl ow adjustment and air

intake control

Turn the control from posi-
tion 1 to position 4 to obtain

an air fl ow suffi cient to en-

sure your comfort.

As soon as possible, position the
control in the exterior air intake
position to prevent misting of the
windows.

This is the normal operating position.

Passenger compartment
isolation.

This position prevents exterior odours
and smoke entering the passenger
compartment.

1. Air fl ow adjustment

37

COMFORT -

These settings are recommended for
cold climates.

3. Temperature adjustment
To be adjusted to your requirements.
From blue (exterior temperature) to
red (hot).

4. Air distribution adjustment

This setting is recommended for high
temperatures.

Windscreen and side windows
(de-icing/demisting).

To quickly de-ice or demist the wind-
screen and side windows:
-

position the air intake control in
the ''Outside Air" position,

- turn the temperature and air fl ow

controls to maximum,

-

close the centre vents.

Windscreen, side windows
and footwells.

Footwells.

Centre and side vents.

COMFORT

38 -

Press the switch to activate
the air conditioning. The indi-
cator light comes on.

2. Air fl ow adjustment and air

intake control

Turn the control from posi-
tion 1 to position 4 to obtain

an air fl ow suffi cient to en-

sure your comfort.

AIR CONDITIONING

The air conditioning does not

operate while the air fl ow adjust-

ment control is in the minimum

position.
Note: to optimise the operation of
the air conditioning, leave the vents
open.

1. Air conditioning control
The air conditioning is designed to
operate in all seasons. In summer,
it enables the temperature to be
lowered and in winter, above 0 °C,
it increases the effectiveness of the
demisting.

39

COMFORT -

Additional heater
Vehicles which are fi tted with an HDI

engine may be fi tted with automatic

additional heating to improve your
comfort.
When the engine is idling or the vehi-
cle is stationary, it is quite normal to
notice a high-pitched whistling noise
and a slight emission of smoke and
odour.

Centre and side vents.

This setting is recommended for high
temperatures.

Recirculation of interior air.

This position prevents exterior odours
and smoke entering the passenger
compartment.
Used simultaneously with the air con-
ditioning, recirculation enables both
heating and cooling performance to
be improved.
Used without the air conditioning,
recirculation may result in misting of
the windows.
As soon as possible, position the
control in the exterior air intake posi-
tion.

3. Temperature adjustment
To be adjusted to your requirements.
From blue (cold when the air condi-
tioning is on) to red (hot).

4. Air distribution adjustment

Windscreen and side windows
(de-icing/demisting).

To quickly de-ice or demist the wind-
screen and side windows:
- turn the temperature and air fl ow

controls to maximum,

-

close the centre vents,

-

position the air intake control in
the "Outside Air" position,

-

start the air conditioning.

Footwells.

These settings are recommended for
cold climates.

Windscreen, side windows
and footwells.

Intake of exterior air.

This is the normal operating position.

SEATS

40 -

41

SEATS -

FRONT SEATS

The adjustment is correct when
the upper edge of the head re-
straint is level with the top of the
head.

To remove the head restraint, place it
in the top position, press the tabs and
pull it upwards.
To put it back in position, locate the
stems of the restraint in the holes,
taking care to keep them in line with
the seat back.

No person or object must pre-
vent the seat from returning
to its initial position; return to
this position is necessary for
the seat to lock in place.

4. Forwards-backwards

adjustment

Lift the control and slide the seat for-
wards or backwards.

1. Head restraint height

adjustment

To raise or lower the restraint, slide it.

2. Armrests
These can be folded back.

3. Seat back angle adjustment

5. Storage drawer (version with

passenger air bag)

There is a storage drawer under the
front passenger seat.
To open it, lift it and pull.

6. Heated seats switch
Press the switch. The temperature is
controlled automatically.
Pressing the switch again stops op-
eration.
Note: the command for activation of
heating of the seat(s) remains memo-
rised for two minutes after the ignition
has been switched off.

7. Access to rear seats

(version with one
sliding side door only)

Do not place heavy objects
in the drawers.

A. Turn the knob.

B. Pull the lever (version

with one sliding side
door only).

Never drive with the head
restraints

removed;

they

must be in place and cor-
rectly adjusted.

Lift the control to fold the seat back
and move the seat forwards.
On repositioning, the seat returns to
its initial position (driver's side).

SEATS

42 -

MULTIFUNCTION PASSENGER SEAT

To fold the seat fully:
Pull the control 2 upwards and tilt the
whole seat.
It is not necessary to remove the
head restraint.
This provides access to a box which
enables you to store objects so that
they cannot be seen from outside the
vehicle.

If your vehicle is not fi tted with a load

blocking partition, it can accommo-
date long objects (up to 2.10 m).
These must be placed on the front

edge of the fl oor and secured using

the rear bar of the boot or using the
lashing rings.

To fold the seat back:
Pull the control 1 upwards and tilt the
seat back.
This provides a fl at surface, recess-

es for drinks and a strap for retaining
documents.

43

SEATS -

To fold the rear bench seat:
-

lower the head restraint,

-

press control 1 to unlock the seat
back 2 ,

-

fold the seat back 2 onto the seat,

-

place the seat in the "folded" posi-
tion.

When repositioning:
-

tilt the folded seat rearwards,

-

lift the seat back,

-

check that the seat is locked cor-
rectly.

Take care not to trap the seat belts.

REAR BENCH SEAT
(5 SEAT VERSION)

HEAD RESTRAINT

This is of the "comma" type.
High position: press the two tabs at
the same time, lift the head restraint
and raise it.
Low position: push the two tabs at
the same time and press the top to
lower the head restraint.
To remove the head restraint: place
it in the high position, lift it then re-
move it.
Store it inside the vehicle, securing

it fi rmly.
To install the head restraint: engage
the rods of the head restraint in the
holes keeping it in line with the seat
back.

SEATS

44 -

REAR BENCH SEATS
(7 SEAT VERSION)

The bench seats of row 2 and row 3
are independent and adjustable.

Row 2 bench seat

Placing the bench seat in the
table position
-

Lower the head restraints fully.

-

Operate the control to fold the
seat back onto the bench seat
cushion.

Returning the seat back to
the sitting position
-

Return the seat back to its original
position and check that it is se-
cured on the pillar of the vehicle.

Placing the bench seat in the fully
folded position
-

Place the seat in the table posi-
tion.

-

Pull the handle, located behind
the bench seat, to release the
feet from their anchorage on the

fl oor.

-

Tilt the bench seat forwards.

Returning the bench seat to its
original position

Before folding the bench seat,
ensure that:

-

in row 3, no passenger's foot is at
one of the bench seat anchorages

on the fl oor,

-

the seat belt is available for the
side passenger.

-

fold back the bench seat.

45

SEATS -

Row 3 bench seat

Placing the seat back in the table
position
-

Lower the head restraints fully.

-

Operate the two controls simulta-
neously to fold the seat back onto
the bench seat cushion.

Returning the seat back to the
sitting position
-

Return the seat back to its original
position and check that it is se-
cured on the pillars of the vehicle.

Placing the bench seat in the fully
folded position
-

Place the seat in the table position.

-

Raise the handle, located behind
the bench seat, to release the
feet from their anchorage on the

fl oor.

-

Tilt the bench seat forwards.

Returning the bench seat to its
original position
-

Before folding back the bench
seat, ensure that the seat belt
is available for the side passen-
gers.

-

Fold back the bench seat.

Access to row 3

From the vehicle's right-hand sliding
door, a passage next to the row 2
bench seat provides access to the
row 3 bench seat.

Good practice

Do not place hard or heavy
objects on the seat backs
forming a table, they could

become dangerous projectiles in the
event or sharp braking or impact.
Following the various operations:
-

do not remove a head restraint

without storing it, fi x it to a sup-

port in the vehicle,

-

do not block the passage to row 3,

-

ensure that the passengers can
always access the seat belts and
fasten them easily,

-

a passenger must never take his
seat without adjusting and fasten-
ing his seat belt.

-

a passenger seated in row 3 must
ensure that he does not obstruct
the row 2 bench seat anchoring
recesses.

SEATS

46 -

GENERAL POINTS RELATING
TO CHILD SEATS

Although one of CITROËN's main
criteria when designing your vehicle,
the safety of your children also de-
pends on you.
For maximum safety, please follow
these precautions:
-

all children under the age of 12

or less than one metre fi fty tall

must travel in approved child
seats suited to their weight ,

on seats fi tted with a seat belt or

ISOFIX mountings * .

-

a child weighing less than 9 kg
must travel in the "rearwards-
facing" position in the front.

SEAT BELT

"Forwards-facing"
When a "forwards-facing" child seat
is installed on the front passenger
seat , adjust the vehicle's seat to the
intermediate

longitudinal

position

with the seat back upright and leave
the passenger air bag armed.

* The rules for transporting chil-

dren are specifi c to each country.

Consult the current legislation in
your country.

Intermediate longitudinal

position

"Rearwards-facing"
When a "rearwards-facing" child seat
is installed on the front passenger
seat , it is essential that the passen-
ger air bag * is disarmed. Otherwise,
the child would risk being seri-
ously injured or killed if the air bag

were to infl ate .

47

SEATS -

CHILD SEATS RECOMMENDED BY CITROËN

CITROËN offers a complete range of recommended child seats which are
secured using a three point seat belt :

Group 0: from birth to 10 kg

Group 0+: from birth to 13 kg

L1

"ROMER Baby-Safe Plus"

Installed in the rear-facing position.

Groups 1, 2 and 3: from 9 to 36 kg

L2

"KIDDY Life"

The use of the restraining cushion is

compulsory for transporting young

children (from 9 to 18 kg).

Groups 2 and 3: from 15 to 36 kg

L3

"RECARO Start''.

L4

"KLIPPAN Optima"

From the age

of 6 years

(approximately 22 kg),
the booster is used on

its own.

Passenger airbag OFF

47

SEATS -

CHILD SEATS RECOMMENDED BY CITROËN

CITROËN offers a complete range of recommended child seats which are
secured using a three point seat belt :

Group 0: from birth to 10 kg

Group 0+: from birth to 13 kg

L1

"ROMER Baby-Safe Plus"

Installed in the rear-facing position.

Groups 1, 2 and 3: from 9 to 36 kg

L2

"KIDDY Life"

The use of the restraining cushion is

compulsory for transporting young

children (from 9 to 18 kg).

Groups 2 and 3: from 15 to 36 kg

L3

"RECARO Start''.

L4

"KLIPPAN Optima"

From the age

of 6 years

(approximately 22 kg),
the booster is used on

its own.

Passenger airbag OFF

SEATS

48 -

INSTALLING CHILD SEATS SECURED USING THE SEAT BELT

In accordance with European regulations, this table indicates the options for the installation of child seats secured using the
seat belt and universally approved (a), in accordance with the weight of the child and the seat in the vehicle:

Weight of the child and indicative age

Seat

Below 13 kg

(groups 0 (b) and 0+)

Up to 1 year approx

From 9 to 18 kg

(group 1)

From 1 to 3 years approx

From 15 to 25 kg

(group 2)

From 3 to 6 years approx

From 22 to 36 kg

(group 3)

From 6 to 10 years approx

Front passenger (c)

U

U

U

U

Row 2

Side

U

U

U

U

Centre

U

U

U

U

Row 2 *

Right

U

U

U

U

Left

U

U

U

U

Row 3 *

Side

U

U

U

U

Centre

U

U

U

U

49

SEATS -

"ISOFIX" MOUNTINGS

These are two rings located between
the seat back and the seat cushion.
This ISOFIX mounting system gua-

rantees reliable, safe and fast fi tting

of the child seat in your vehicle.

The ISOFIX child seats

are fi tted

with two locks which are secured
easily on these rings.

Your vehicle has been approved in ac-
cordance with the ISOFIX regulation .
The seats, represented below, are fi t-

ted * with regulation ISOFIX mountings:

(a) Universal child seat: child seat

which can be installed in all ve-
hicles using the seat belt.

(b) Group 0: from birth to 10 kg.
(c) Consult the legislation in force

in your country before installing
your child on this seat.

U Seat suitable for the installation of

a child seat secured using a seat
belt and universally approved,
"rear facing" and/or "forward
facing".

* Ludospace 7 seat version: mountings

not available.