Ford Focus RS (2011 year). Manual — part 122
1
2
3
5
6
7
4
0
1
0
6
8
3
4
E62636
1928
1468
1173
1064
1438
2006
1566
1294
1177
1820
1203
2
5
7
997
1848
2015
8
1750
1924
4. NOTE: The body dimensions of the front
floor pan are the same as for the 3-, 4- and
5-door and can be taken from illustration
E43251.
Body dimensions, wagon
• All dimensions are measured starting from
the centre of each hole, using an electronic
G371029en
501-26-
41
and Tolerance Checks
501-26-
41
GENERAL PROCEDURES
measuring system and with the assemblies
removed.
• A tolerance of ± 3 mm applies to all
measurements given. All detailed illustrations
correspond to the left-hand side of the
vehicle.
3
4
7
1
1
3
4
E62637
2
7
8
306
1378
1024
1096
423
634
342
140
5
2
6
987
988
1097
1126
612
1045
1228
5
6
8
G371029en
501-26-
42
and Tolerance Checks
501-26-
42
GENERAL PROCEDURES
Frame Tolerance Check
1. Front end body dimensions, all models
• All dimensions have a tolerance of ± 3 mm.
All dimensions were determined starting from
the center of each hole or panel edge using
a symmetrically adjusted beam trammel.
Measuring points and dimensions
1 - 6 = 1496 mm
1 - 2 = 530 mm
1 - 7 = 1532 mm
1 - 3 = 608 mm
1 - 8 = 1556 mm
1 - 4 = 786 mm
9 - 10 = 965 mm
1 - 5 = 1426 mm
G371030en
501-26-
43
and Tolerance Checks
501-26-
43
GENERAL PROCEDURES
1
7
6
8
9
10
3
2
4
5
1
10
9
8
2
3
4
7
6
5
E54960
2. Body dimensions, side view (5-door version)
• All dimensions have a tolerance of ± 3 mm.
All dimensions were determined starting from
the edge of the steel panel using a
symmetrically adjusted measuring gauge.
• Measuring points 1, 2, 3, 4, 6, 7, 10 and 11
are measured in the curve and represent the
G371030en
501-26-
44
and Tolerance Checks
501-26-
44
GENERAL PROCEDURES
greatest distance to the measuring point
opposite.
• The detail views of measuring points 5, 8, 9
and 12 are shown looking from the vehicle
interior outwards.
Measuring points and dimensions
4 - 7 = 1095 mm
1 - 10 = 992 mm
5 - 8 = 711 mm
2 - 11 = 1281 mm
9 - 12 = 838 mm
3 - 6 = 1025 mm
G371030en
501-26-
45
and Tolerance Checks
501-26-
45
GENERAL PROCEDURES
E54961
1
3
2
10
11
12
7
6
9
8
5
4
5
6
7
9
8
10
2
1
3
4
11
12
3. Body dimensions, rear (5-door version)
• All dimensions have a tolerance of ± 3 mm.
All dimensions were determined starting from
the center of the welded flange using a
symmetrically adjusted measuring gauge.
G371030en
501-26-
46
and Tolerance Checks
501-26-
46
GENERAL PROCEDURES
Measuring points and dimensions
3 - 6 = 1327 mm
1 - 4 = 1115 mm
2 - 5 = 996 mm
E63019
1
2
3
4
5
6
4. Body dimensions, interior (5-door version)
• All dimensions have a tolerance of ± 3 mm.
All dimensions were determined starting from
G371030en
501-26-
47
and Tolerance Checks
501-26-
47
GENERAL PROCEDURES
the center of the welded flange using a
symmetrically adjusted measuring gauge.
Measuring points and dimensions
5 - 6 = 1441 mm
1 - 4 = 1458 mm
2 - 3 = 1442 mm
2
3
6
5
4
1
E54964
G371030en
501-26-
48
and Tolerance Checks
501-26-
48
GENERAL PROCEDURES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст