Ford Focus RS (2011 year). Manual — part 26
Rear Seat Backrest Cover
General Equipment
Hog ring pliers
1. Remove the components in the order
indicated in the following illustration(s) and
table(s).
NOTE: Left-hand rear seat backrest shown.
E50964
1
5
4
6
3
2
9
8
7
10
G401850en
501-10-
32
Seating
501-10-
32
REMOVAL AND INSTALLATION
Description
Item
Armrest (if equipped)
See Removal Detail
See Installation Detail
1
Armrest backing plate (if equipped)
See Removal Detail
See Installation Detail
2
Rear seat backrest outer pivot pin bush
See Removal Detail
3
Head restraints (if equipped)
4
Head restraint guide tubes (if equipped)
See Removal Detail
5
Rear seat backrest release button trim
panel
6
Description
Item
Rear center safety belt webbing trim panel
See Removal Detail
See Installation Detail
7
Rear seat backrest frame
See Removal Detail
See Installation Detail
8
Rear seat backrest pad
See Removal Detail
See Installation Detail
9
Rear seat backrest cover
See Installation Detail
10
2. To install, reverse the removal procedure.
Removal Details
Item 1
Armrest (if equipped)
1. Remove the armrest.
1. Slide the armrest upwards.
2. Slide the armrest outwards.
E48658
2
1
2. Remove and discard the armrest pivot bush
spring clips (the rear seat backrest cover
and pad are shown removed for clarity).
E51565
Item 2
Armrest backing plate (if equipped)
1. Remove the armrest backing plate.
G401850en
501-10-
33
Seating
501-10-
33
REMOVAL AND INSTALLATION
• Detach the retaining clips from the rear seat
backrest in the sequence shown.
E48659
3
2
1
4
Item 3
Rear seat backrest outer pivot pin bush
1. Fold the rear seat cushions forwards.
2. Release the rear seat backrest upper latch
on both sides.
3. Fold the rear seat backrests forwards.
4. Release the rear seat backrest from the outer
mounting bracket on both sides.
1. Using a pair of long nose pliers, depress the
clips.
2. Push the clip inwards.
3. Using a screwdriver, release the locking
latch.
E50069
1
1
3
2
5.
CAUTION: The left-hand rear seat
backrest inner pivot pin has radial grooves.
Take care not to damage the right-hand rear
seat backrest inner pivot bush.
Remove the right-hand rear seat backrest.
1. Detach the outer pivot pin from the mounting
bracket.
2. Detach the right-hand rear seat backrest from
the left-hand rear seat backrest.
E50071
2
1
6.
CAUTION: Make sure that a webbing
retainer is installed at least 200 mm towards
the rear center safety belt retractor from the
webbing stop.
Install the safety belt webbing retainer.
E48648
7.
CAUTION: The bolt securing the rear
center safety belt lower anchor is held
captive by a metal washer. The bolt and
metal washer must remain on the safety belt
lower anchor at all times when the safety belt
is detached or removed.
G401850en
501-10-
34
Seating
501-10-
34
REMOVAL AND INSTALLATION
Remove the rear center safety belt lower
anchor retaining bolt.
E49461
55 Nm
8.
CAUTION: The left-hand rear seat
backrest inner pivot pin has radial grooves.
Take care not to damage the center hinge
pivot bush.
Remove the left-hand rear seat backrest.
1. Detach the outer pivot pin from the mounting
bracket.
2. Slide the backrest from the center mounting
bracket.
E50070
1
2
9. Remove the rear seat backrest outer pivot
pin bush.
• Remove the rear seat backrest outer pivot
pin bush retaining bolt.
E53200
35 Nm
Item 5
Head restraint guide tubes (if equipped)
1.
CAUTION: Make sure that the head
restraint guide tube locking tang is fully
depressed before removal.
Remove the head restraint guide tubes.
1. Using a screwdriver, depress the locking
tang.
2. Pull the guide tube upwards.
E0031543
1
2
1
Item 7
Rear center safety belt webbing trim
panel
1.
CAUTION: Make sure that a webbing
retainer is installed at least 200 mm towards
the rear center safety belt retractor from the
webbing stop.
G401850en
501-10-
35
Seating
501-10-
35
REMOVAL AND INSTALLATION
Remove the rear center safety belt webbing
trim panel.
E51474
200
mm
1
2
Item 8
Rear seat backrest frame
1. Detach the rear seat backrest cover from the
rear seat backrest frame.
E51467
2. Detach the rear seat backrest cover from the
rear seat backrest release button.
TIE0000374
3. Feed the rear center safety belt and lower
anchor through the rear seat backrest cover
and pad.
TIE0003255
4. Remove the rear seat backrest cover and
pad.
E51127
Item 9
Rear seat backrest pad
1. Remove the rear seat backrest cover.
• Cut the hog rings.
G401850en
501-10-
36
Seating
501-10-
36
REMOVAL AND INSTALLATION
• Discard the hog rings.
TIE0004799
Installation Details
Item 10
Rear seat backrest cover
NOTE: If a replacement rear seat backrest cover
is to be installed, cut out holes for the head restraint
guide tubes and rear center safety belt webbing
trim panel. Use the existing rear seat backrest
cover as a template.
Item 9
Rear seat backrest pad
1. NOTE: If a replacement rear seat backrest
cover is to be installed, cut out a hole for the
rear center safety belt webbing trim panel.
Use the existing rear seat backrest pad as a
template.
Do not use any other tool. The hog rings must be
closed to overlap as illustrated.
NOTE: Install new hog rings.
V4001063
Item 8
Rear seat backrest frame
CAUTIONS:
Make sure that a webbing retainer is
installed at least 200 mm towards the rear
center safety belt retractor from the
webbing stop.
When attaching the rear seat backrest
cover and pad take care not to detach the
safety belt webbing retainer.
After installation check for correct
operation of the rear center safety belt
retractor.
Item 7
Rear center safety belt webbing trim
panel
CAUTIONS:
Make sure that a webbing retainer is
installed at least 200 mm towards the rear
center safety belt retractor from the
webbing stop.
After installation check for correct
operation of the rear center safety belt
retractor.
1. Install the rear center safety belt webbing
trim panel.
G401850en
501-10-
37
Seating
501-10-
37
REMOVAL AND INSTALLATION
Using hog ring pliers
, install the hog rings.
NOTE: Use hog ring pliers to close the hog rings.
E51475
Item 2
Armrest backing plate (if equipped)
1.
CAUTION: Install the armrest to the rear
seat backrest before installing the armrest
backing plate.
Item 1
Armrest (if equipped)
WARNING: New armrest pivot bush spring
clips must be installed. Failure to follow
this instruction may result in personal
injury.
1. Install the armrest pivot bush spring clips
(the rear seat backrest cover and pad are
shown removed for clarity).
E51565
2. NOTE: Make sure that the armrest pivot bush
spring clips locate in the armrest pivot bush
grooves.
Install the armrest.
1. Place the upper end of the armrest into the
upper end of the armrest aperture.
2. Locate the armrest pivot bushes into the
armrest retaining bracket.
E51513
1
2
G401850en
501-10-
38
Seating
501-10-
38
REMOVAL AND INSTALLATION
Rear Seat Backrest Cover — 2.5L Duratec-ST (166kW/226PS) -
VI5
Removal
NOTE: Removal steps in this procedure may
contain installation details.
All vehicles
1. Torque: 35 Nm
E65705
2.
E0031543
1
2
1
Vehicles with seat mounted safety belt
retractors
3. NOTE: If the safety belt webbing retracts further
than the safety belt webbing stop, a new safety
belt retractor must be installed.
E51474
200
mm
1
2
4. Torque: 55 Nm
E65704
G545262en
501-10-
39
Seating
501-10-
39
REMOVAL AND INSTALLATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст