Ford Focus RS (2011 year). Manual — part 76
DETAILS/RESULTS/ACTIONS
TEST CONDITIONS
4 Measure voltage between right-hand windshield
washer nozzle heater, connector C720, pin 1,
circuit 15-HB26 (GN/RD), wiring harness side
and ground.
• Does the meter display battery voltage?
ൺ
Yes
VFE0016017
GO to N6.
ൺ
No
LOCATE and RECTIFY break in circuit
between soldered connection S123 and right-
hand windshield washer nozzle heater using
the Wiring Diagrams. CHECK the operation
of the system.
N6: CHECK GROUND SUPPLY TO RIGHT WINDSHIELD WASHER NOZZLE HEATER FOR OPEN
CIRCUIT
1 Ignition switch in position 0.
2 Measure the resistance between the right-hand
windshield washer nozzle heater, socket C720,
pin 2, circuit 31-HB26 (BK), wiring harness side
and ground.
• Is the resistance less than 2 ohms?
ൺ
Yes
VFE0022794
RENEW the right-hand windshield washer
nozzle heater. CHECK the operation of the
system.
ൺ
No
LOCATE and RECTIFY break in circuit
between right-hand windshield washer nozzle
heater and soldered connection S122 using
the Wiring Diagrams. CHECK the operation
of the system.
Component Tests
Front wiper motor
1. TEST the front windshield wiper motor in park
position:
• Measure the resistance at the front
windscreen wiper motor between pin 3 and
pin 4 (or the housing of the wiper motor).
• Is the resistance less than 2 ohms?
• If yes then the wiper motor is OK.
• If not, RENEW the wiper motor.
VFE48149
G401883en
501-16-
58
Wipers and Washers
501-16-
58
DIAGNOSIS AND TESTING
Wash/wipe system switch
Pin assignment:
1
6
7
12
VFE53074
The switch is OK if
Set the switch to the
following position
Connect ohmmeter to
the following terminal
pins
Circuit to test
Circuit closed
Intermittent
3 and 12
Intermittent
Circuit closed
Intermittent level 1
3 and 7
Variable delay
Circuit open
Intermittent level 1
3 and 9
Circuit open
Intermittent level 1
3 and 11
Circuit closed
Intermittent level 2
3 and 7
Variable delay
Circuit closed
Intermittent level 2
3 and 9
Circuit open
Intermittent level 2
3 and 11
Circuit open
Intermittent level 3
3 and 7
Variable delay
Circuit closed
Intermittent level 3
3 and 9
Circuit open
Intermittent level 3
3 and 11
Circuit open
Intermittent level 4
3 and 7
Variable delay
Circuit closed
Intermittent level 4
3 and 9
Circuit closed
Intermittent level 4
3 and 11
Circuit closed
Intermittent level 5
3 and 7
Variable delay
Circuit closed
Intermittent level 5
3 and 9
Circuit closed
Intermittent level 5
3 and 11
Circuit closed
Intermittent level 6
3 and 7
Variable delay
Circuit open
Intermittent level 6
3 and 9
Circuit closed
Intermittent level 6
3 and 11
G401883en
501-16-
59
Wipers and Washers
501-16-
59
DIAGNOSIS AND TESTING
Windshield Wiper Blade and Pivot Arm Adjustment
Special Tool(s)
Aligner, Wiper Arm
501-027 (32-006)
ES32006
General Equipment
Aero-Wiper Measuring and Adjusting Tools AWPE
02 (Order No. 511 5124 001 00)
Vehicles without beam blade wipers
1.
CAUTION: Make sure that the wiper motor
is in the park position.
Remove the wiper blade.
2. Insert the wiper arm in the special tool and
place the special tool on the windshield.
3. NOTE: All three support points of the special
tool must be in contact with the glass.
NOTE: The angle of the wiper on the scale must
point from the zero center line to the center of the
windshield/rear window. Ignore the sign (+/-) on
the alignment tool.
Using the special tool, read off the angle
between the wiper arm and the windshield.
1. Center of windshield
E56969
501-027
1
4. NOTE: Lift the special tool away from the
glass when correcting the angle, in order to
prevent damage.
Using an open-ended wrench on the special
tool, adjust the wiper arm. For additional
information,
refer to Specifications.
E56970
5. Remove the special tool.
6. Install the wiper blade.
Vehicles with beam blade wipers
1. Connect the adapter "B" with the angle
measuring instrument.
• Tighten the knurled screw finger tight.
E60132
2.
CAUTION: Make sure that the wiper motor
is in the park position.
Remove the wiper blade.
3. Insert the wiper arm in the angle measuring
instrument and place the angle measuring
instrument on the windshield.
G18564en
501-16-
60
Wipers and Washers
501-16-
60
GENERAL PROCEDURES
1. Center of windshield
E60133
1
4. NOTE: All three support points of the angle
measuring instrument must be in contact
with the glass.
NOTE: The angle of the wiper on the scale must
point from the zero center line to the center of the
windshield/rear window. Ignore the sign (+/-) on
the alignment tool.
Using the angle measuring instrument, read
off the angle between the wiper arm and the
windshield.
5. CAUTIONS:
Make sure that no mechanical force is
applied to the wiper blade holder while
adjusting the angle.
The wiper arm must not be adjusted by
more than three degrees. If a bigger
adjustment is necessary, check the wiper
arm for damage, replace if necessary.
NOTE: Lift the angle measuring instrument away
from the glass when correcting the angle, in order
to prevent damage.
Using the adjusting tool and the counter
holder, adjust the wiper arm. For additional
information,
refer to Specifications.
E60134
6. Remove the angle measuring instrument.
7. Install the wiper blade.
G18564en
501-16-
61
Wipers and Washers
501-16-
61
GENERAL PROCEDURES
Windshield Wiper Motor
1. Remove the components in the order
indicated in the following illustration(s) and
table(s).
CAUTION: Make sure that the windshield wiper motor is in the park position.
E51544
1
22 Nm
5
7 Nm
3
6
7
4
8
2
Description
Item
Windshield wiper arm nuts
1
Windshield wiper arms
See Installation Detail
2
Clips, cowl panel grille
3
Cowl panel grille
4
Bolts for windshield wiper motor with
linkage
5
Front wiper linkage
6
Description
Item
Windshield wiper motor connector
7
Windshield wiper motor
See Removal Detail
8
2. To install, reverse the removal procedure.
3. Check the angle of the windshield wiper arms
in relation to the windshield.
For additional information,
refer to:
Windshield Wiper Blade and Pivot Arm
Adjustment
(501-16 Wipers and Washers,
General Procedures).
Removal Details
G413303en
501-16-
62
Wipers and Washers
501-16-
62
REMOVAL AND INSTALLATION
Item 8
Windshield wiper motor
1. Detach the wiper linkage from the Windshield
wiper motor lever arm.
E51545
2. Remove the windshield wiper motor bolts.
E51546
9 Nm
3. Pull windshield wiper motor from the wiper
motor bracket.
E51547
Installation Details
Item 2
Windshield wiper arms
CAUTION: Move the windshield wiper
motor to park position before installing the
windshield wiper arms.
G413303en
501-16-
63
Wipers and Washers
501-16-
63
REMOVAL AND INSTALLATION
Windshield Washer Pump(32 624 0)
1. Empty the windshield washer reservoir.
2. Detach the right-hand front wheel.
For additional information,
refer to: Wheel
and Tire
(204-04 Wheels and Tires, Removal
and Installation).
3. Remove the right-hand wheelhouse cover.
VFE0037199
4. Remove the components in the order
indicated in the following illustration(s) and
table(s).
E51866
3
6
5
1
4
2
7
Description
Item
Front windscreen washer lower reservoir
connecting piece
See Removal Detail
1
Windshield washer upper reservoir lower
retaining bolt
2
Description
Item
Windshield washer upper reservoir upper
retaining bolt
3
Windshield washer upper reservoir
See Removal Detail
4
Front windscreen washer pump connector
5
G413304en
501-16-
64
Wipers and Washers
501-16-
64
REMOVAL AND INSTALLATION
Description
Item
Windshield washer pump hoses.
See Removal Detail
6
Description
Item
Windshield washer pump
See Installation Detail
7
5. To install, reverse the removal procedure.
Removal Details
Item 1
Front windscreen washer lower reservoir
connecting piece
1. Pull the connecting piece of the lower
reservoir from the upper reservoir.
E44197
Item 4
Windshield washer upper reservoir
1. Pull the reservoir from the filler neck.
E51867
Item 6
Windshield washer pump hoses.
1. Unclip the reservoir hoses.
Installation Details
Item 7
Windshield washer pump
1. Coat the pump rubber seal – on the front
windscreen washer with soap prior to
installation.
G413304en
501-16-
65
Wipers and Washers
501-16-
65
REMOVAL AND INSTALLATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст