Ford Focus RS (2011 year). Manual — part 146
Item 9
Rear lower arm adjustment cam nut
1. NOTE: Do not fully tighten the rear lower arm
adjustment cam nut at this stage.
NOTE: Align the mark on the rear lower arm
adjustment cam to the mark on the rear axle
crossmember.
Install the rear lower arm adjustment cam
nut on both sides.
TIE0036771
8 Nm
Item 4
Stabilizer bar
1. Lower the suspension from the design height
setting on both sides.
1. Remove the spacer.
2. Install the bump stop.
TIE45129
1
2
2. Position the stabilizer bar.
G422315en
502-00-
36
Uni-Body, Subframe and Mounting System
502-00-
36
REMOVAL AND INSTALLATION
Rear Axle Crossmember — Vehicles With: Ball Joint Stabilizer
Bar Link, Vehicles Without: Fuel Additive Tank
General Equipment
Securing strap
Transmission jacks
1. Remove the spring on both sides.
2. Remove the evaporative emission canister
(if equipped).
3. Remove the headlamp leveling rear sensor
(if equipped).
For additional information, refer to:
Exterior Lighting, Removal and
Installation).
4. Detach the headlamp leveling sensor wiring
harness from the rear axle crossmember (if
equipped).
E44185
5. Detach the headlamp leveling sensor wiring
harness from the rear axle crossmember and
disconnect the electrical connector (if
equipped).
E44186
6. Remove the components in the order
indicated in the following illustration(s) and
table(s).
G401869en
502-00-
37
Uni-Body, Subframe and Mounting System
502-00-
37
REMOVAL AND INSTALLATION
Headlamp Leveling Rear Sensor
(417-01
E45204
2
1
Description
Item
Evaporative emission canister heat shield
to rear axle crossmember stud (if
equipped)
1
Evaporative emission canister heat shield
to rear axle crossmember retaining bolt (if
equipped)
2
G401869en
502-00-
38
Uni-Body, Subframe and Mounting System
502-00-
38
REMOVAL AND INSTALLATION
E53196
48 Nm
3
4
Description
Item
Stabilizer bar clamp retaining bolts
3
Stabilizer bar
See Installation Detail
4
G401869en
502-00-
39
Uni-Body, Subframe and Mounting System
502-00-
39
REMOVAL AND INSTALLATION
E53191
115 Nm
5
6
Description
Item
Front lower arm retaining bolts
See Removal Detail
5
Front lower arm
See Removal Detail
6
G401869en
502-00-
40
Uni-Body, Subframe and Mounting System
502-00-
40
REMOVAL AND INSTALLATION
E53192
8
115 Nm
7
11
9
115 Nm
10
Description
Item
Upper arm retaining bolts
See Removal Detail
7
Upper arm
8
Rear lower arm adjustment cam nut
See Removal Detail
See Installation Detail
9
Description
Item
Rear lower arm to wheel knuckle retaining
bolt
10
Rear lower arm
See Installation Detail
11
G401869en
502-00-
41
Uni-Body, Subframe and Mounting System
502-00-
41
REMOVAL AND INSTALLATION
E53193
12
Description
Item
Exhaust hanger insulator
See Removal Detail
12
G401869en
502-00-
42
Uni-Body, Subframe and Mounting System
502-00-
42
REMOVAL AND INSTALLATION
E53194
14
13
13
Description
Item
Rear axle crossmember retaining bolts
See Removal Detail
See Installation Detail
13
Rear axle crossmember
See Installation Detail
14
7. To install, reverse the removal procedure.
8. Check the toe setting and adjust as
necessary. For additional information, refer
to: (204-00 Suspension System - General
Information)
Specifications
(Specifications),
9. NOTE: Final tightening of the rear lower arm
adjustment cam nut must be carried out
when the vehicle weight is on the road
wheels.
Tighten the rear lower arm adjustment cam
nut on both sides.
TIE39079
90 Nm
Removal Details
G401869en
502-00-
43
Uni-Body, Subframe and Mounting System
502-00-
43
REMOVAL AND INSTALLATION
Rear Toe Adjustment
(General Procedures).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст