Hyundai Ioniq Hybrid (2019 year). Manual — part 25
You may not be able identify a tire
i
Information
WARNING
with low pressure by simply looking
at it. Always use a good quality tire
This device complies with Part 15 of
Tampering with, modifying, or
the FCC rules.
pressure guage to measure the tire's
disabling the Tire Pressure
inflation pressure. Please note that a
Operation is subject to the following
Monitoring System
(TPMS)
tire that is hot (from being driven) will
three conditions:
components may interfere with
have a higher pressure measure-
1. This device may not cause harmful
the system's ability to warn the
ment than a tire that is cold.
interference, and
driver of low tire pressure con-
A cold tire means the vehicle has
ditions and/or TPMS malfunc-
2. This device must accept any inter-
been sitting for 3 hours and driven for
tions. Tampering with, modify-
ference received, including interfer-
less than 1 mile (1.6 km) in that 3
ing, or disabling the Tire
ence that may cause undesired
hour period.
Pressure Monitoring System
operation.
Allow the tire to cool before measur-
(TPMS) components may void
3.
Changes or modifications not
ing the inflation pressure. Always be
the warranty for that portion of
expressly approved by the party
sure the tire is cold before inflating to
the vehicle.
responsible for compliance could
the recommended pressure.
void the user’s authority to operate
the equipment.
6
WARNING
• The TPMS cannot alert you to
severe and sudden tire dam-
age caused by external fac-
tors such as nails or road
debris.
• If you feel any vehicle instabil-
ity, immediately take your foot
off the accelerator, apply the
brakes gradually with light
force, and slowly move to a
safe position off the road.
6-19
What to do in an emergency
IF YOU HAVE A FLAT TIRE
With Spare Tire (if equipped)
Jack and tools
WARNING
Changing a tire can be danger-
ous. Follow the instructions in
this section when changing a
tire to reduce the risk of serious
injury or death.
OAD065026
CAUTION
Turn the winged hold down bolt
OAD065027
counterclockwise to remove the
Be careful as you use the jack
➀ Jack handle
handle to stay clear of the flat
spare tire.
② Jack
end. The flat end has sharp
Store the spare tire in the same com-
edges that could cause cuts.
③ Wheel lug nut wrench
partment by turning the winged hold
down bolt clockwise.
The jack, jack handle, and wheel lug
To prevent the spare tire and tools
nut wrench are stored in the luggage
from "rattling", store them in their
compartment under the luggage box
proper location.
cover.
The jack is provided for emergency
tire changing only.
6-20
Changing tires
(Continued)
• Do not start or run the engine
WARNING
while the vehicle is on the
jack.
A vehicle can slip or roll off of a
jack causing serious injury or
• Do not allow anyone to remain
in the vehicle while it is on the
death to you or those nearby.
Take the following safety pre-
jack.
cautions:
• Keep children away from the
road and the vehicle.
•
Never place any portion of
your body under a vehicle that
OLF064005
is supported by a jack.
Follow these steps to change your
If it is hard to loosen the tire hold-
•
NEVER attempt to change a
vehicle's tire:
down wing bolt by hand, you can
tire in the lane of traffic.
loosen it easily using the jack handle.
1. Park on a level, firm surface.
ALWAYS move the vehicle
1. Put the jack handle (1) inside of
completely off the road on
2. Move the shift lever into P (Park),
the tire hold-down wing bolt.
level, firm ground away from
apply the parking brake, and place
6
traffic before trying to change
the Engine Start/Stop button in the
2. Turn the tire hold-down wing bolt
a tire. If you cannot find a level,
OFF position.
counterclockwise with the jack
handle.
firm place off the road, call a
3. Press the hazard warning flasher
towing service for assistance.
button.
•
Be sure to use the jack pro-
4. Remove the wheel lug nut wrench,
vided with the vehicle.
jack, jack handle, and spare tire
•
ALWAYS place the jack on the
from the vehicle.
designated jacking positions
5. Block both the front and rear of the
on the vehicle and NEVER on
tire diagonally opposite of the tire
the bumpers or any other part
you are changing.
of the vehicle for jacking sup-
port.
(Continued)
6-21
What to do in an emergency
■ Front
■ Rear
Block
OAE066010
OAE066011
OAE066012
6. Loosen the wheel lug nuts coun-
7. Place the jack at the designated
8. Insert the jack handle into the jack
terclockwise one turn each in the
jacking position under the frame
and turn it clockwise, raising the
order shown above, but do not
closest to the tire you are chang-
vehicle until the tire clears the
remove any lug nuts until the tire
ing. The jacking positions are
ground. Make sure the vehicle is
has been raised off of the ground.
plates welded to the frame with
stable on the jack.
two notches. Never jack at any
other position or part of the vehi-
cle. Doing so may damage the
side seal molding or other parts of
the vehicle.
6-22
11. Tighten the lug nuts with your fin-
■ Rear
gers onto the studs with the
smaller end of the lug nuts clos-
est to the wheel.
12. Lower the vehicle to the ground
by turning the jack handle coun-
terclockwise.
13. Use the wheel lug nut wrench to
tighten the lug nuts in the order
shown. Double-check each lug
nut until they are tight. After
OAE066013
OLF064013
changing tires, have an author-
9. Loosen the lug nuts with the wheel
ized HYUNDAI dealer tighten the
If you have a tire gauge, check the
lug nut wrench and remove them
lug nuts to their proper torque as
tire pressure
(see "Tires and
with your fingers. Remove the
soon as possible. The wheel lug
Wheels" in chapter 8 for tire pressure
wheel from the studs and lay it flat
nut should be tightened to
instructions.). If the pressure is lower
on the ground out of the way.
79~94 lbf·ft (11~13 kgf·m).
or higher than recommended, drive
6
Remove any dirt or debris from
slowly to the nearest service station
the studs, mounting surfaces, and
and adjust it to the recommended
wheel.
pressure. Always reinstall the valve
cap after checking or adjusting tire
10. Install the spare tire onto the
pressure. If the cap is not replaced,
studs of the hub.
air may leak from the tire. If you lose
a valve cap, buy another and install it
as soon as possible. After changing
tires, secure the flat tire and return
the jack and tools to their proper stor-
age locations.
6-23
What to do in an emergency
NOTICE
Use of compact spare tires
When driving with the compact spare
(if equipped)
tire mounted to your vehicle:
Check the tire pressure as soon
Compact spare tires are designed for
•
Check the tire pressure after
as possible after installing a spare
emergency use only. Drive carefully
installing the compact spare tire.
tire. Adjust it to the recommended
on the compact spare tire and
The compact spare tire should be
pressure.
always follow the safety precautions.
inflated to 60 psi (420 kPa).
•
Do not take this vehicle through an
CAUTION
WARNING
automatic car wash while the com-
pact spare tire is installed.
Your vehicle has metric threads
To prevent compact spare tire
•
Do not use the compact spare tire
on the studs and lug nuts. Make
failure and loss of control pos-
on any other vehicle because this
certain during tire changing
sibly resulting in an accident:
tire has been designed especially
that the same nuts that were
•
Use the compact spare tire
for your vehicle.
removed are reinstalled. If you
only in an emergency.
•
The compact spare tire’s tread life
have to replace your lug nuts
•
NEVER operate your vehicle
is shorter than a regular tire.
make sure they have metric
over 50 mph (80 km/h).
Inspect your compact spare tire
threads to avoid damaging the
regularly and replace worn com-
studs and ensure the wheel is
•
Do not exceed the vehicle's
pact spare tires with the same size
properly secured to the hub.
maximum load rating or the
and design, mounted on the same
Consult
an
authorized
load carrying capacity shown
wheel.
HYUNDAI dealer for assistance.
on the sidewall of the com-
pact spare tire.
•
Do not use more than one compact
spare tire at a time.
•
Do not use the compact spare
If any of the equipment such as the
tire continuously. Repair or
jack, lug nuts, studs, or other equip-
replace the original tire as
ment is damaged or in poor condi-
soon as possible to avoid fail-
tion, do not attempt to change the
ure of the compact spare tire.
tire and call for assistance.
6-24
NOTICE
With Tire Mobility Kit (TMK)
CAUTION
- Type A
When the original tire and wheel
are repaired and reinstalled on the
To prevent damaging the com-
vehicle, the lug nut torque must be
pact spare tire and your vehicle:
set correctly. The correct lug nut
•
Drive slowly enough for the
tightening torque is
79~94 lbf·ft
road conditions to avoid all
(11~13 kgf·m).
hazards, such as a potholes
or debris.
•
Avoid driving over obstacles.
The compact spare tire diame-
ter is smaller than the diame-
ter of a conventional tire and
reduces the ground clearance
approximately 1 inch (25 mm).
OAE066037N
•
Do not use tire chains on the
For safe operation, carefully read
compact spare tire. Because
and follow the instructions in this
of the smaller size, a tire chain
manual before use.
6
will not fit properly.
(1) Compressor
•
Do not use the compact spare
(2) Sealant bottle
tire on any other wheels, nor
should standard tires, snow
tires, wheel covers or trim
rings be used with the com-
pact spare wheel.
6-25
What to do in an emergency
The Tire Mobility Kit is a temporary fix
Introduction
WARNING
to the tire and the tire should be
With the Tire Mobility Kit you stay
inspected by an authorized HYUNDAI
mobile even after experiencing a tire
Temporary fix
dealer as soon as possible.
puncture.
Have your tire repaired as soon
The compressor and sealing com-
as possible. The tire may lose
CAUTION
pound system effectively and com-
air pressure at any time after
fortably seals most punctures in a
One sealant bottle for one tire
inflating with the Tire Mobility
passenger car tire caused by nails
Kit.
or similar objects and reinflates the
When two or more tires are flat,
tire.
do not use the tire mobility kit
because the supported one
After you ensure that the tire is prop-
sealant of Tire Mobility Kit is
erly sealed you can drive cautiously
only used for one flat tire.
on the tire (distance up to 120 miles
(200 km)) at a max. speed of (50
mph (80 km/h)) in order to reach a
service station or tire dealer for the
WARNING
tire replacement.
Tire wall
It is possible that some tires, espe-
cially with larger punctures or dam-
Do not use the Tire Mobility Kit
age to the sidewall, cannot be sealed
to repair punctures in the tire
completely.
walls. This can result in an acci-
Air pressure loss in the tire may
dent due to tire failure.
adversely affect tire performance.
For this reason, you should avoid
abrupt steering or other driving
maneuvers, especially if the vehicle
is heavily loaded or if a trailer is in
use.
6-26
The Tire Mobility Kit is not designed
•
When the tire and wheel are dam-
•
Do not use the Tire Mobility Kit if
or intended as a permanent tire
aged, do not use Tire Mobility Kit
the ambient temperature is below
repair method and is to be used for
for your safety.
-22°F (-30°C).
one tire only.
•
Use of the Tire Mobility Kit may not
•
In case of skin contact with the-
This instruction shows you step by
be effective for tire damage larger
sealant, wash the area thoroughly-
step how to temporarily seal the
than approximately
0.24 inch
(6
with plenty of water.If the irritation-
puncture simply and reliably.
mm).
persists, seek medical attention.
Read the section "Notes on the safe
Please contact the nearest
•
In case of eye contact with the
use of the Tire Mobility Kit".
HYUNDAI dealership if the tire
sealant,flush your eyes for at least
cannot be made roadworthy with
15 min-utes.If the irritation persists,
the Tire Mobility Kit.
seekmedical attention.
Notes on the safe use of the
•
Do not use the Tire Mobility Kit if a
•
In case of swallowing the
Tire Mobility Kit
tire is severely damaged by driving
sealant,rinse the mouth and drink
• Park your car at the side of the
run flat or with insufficient air pres-
plenty ofwater.However, never give
road so that you can work with the
sure.
anythingto an unconscious person
Tire Mobility Kit away from moving
and seekmedical attention immedi-
•
Do not remove any foreign objects
traffic.
ately.
such as nails or screws that have
6
• To be sure your vehicle will not
penetrated the tire.
•
Long time exposure to the sealant-
move, even when you're on fairly
may cause damage to bodily tis-
•
Provided the car is outdoors, leave
level ground, always set your park-
suesuch as kidney, etc.
the engine running. Otherwise
ing brake.
operating the compressor may
• Only use the Tire Mobility Kit for
eventually drain the car battery.
sealing/inflation passenger car
•
Never leave the Tire Mobility Kit
tires. Only punctured areas located
unattended while it is being used.
within the tread region of the tire
can be sealed using the tire mobil-
•
Do not leave the compressor run-
ity kit.
ning for more than 10 minutes at a
time or it may overheat.
• Do not use on motorcycles, bicy-
cles or any other type of tires.
6-27
What to do in an emergency
Components of the Tire Mobility Kit
1. Speed restriction label
2. Sealant bottle and label with
speed restriction
3. Filling hose from sealant bottle to
wheel
4. Connectors and cable for power
outlet direct connection
5. Holder for the sealant bottle
6. Compressor
7. ON/OFF switch
8. Pressure gauge for displaying the
tire inflation pressure
9. Button for reducing tire inflation
pressure
OAE067039
6-28
Connectors, cable and connection
Using the Tire Mobility Kit
hose are stored in the compressor
housing.
CAUTION
Strictly follow the specified sequence,
otherwise the sealant may escape
under high pressure.
WARNING
Do not use the tire sealant after
OAEPH067041L
the sealant has expired
(i.e.
pasted the expiration date on
2. Screw the filling hose (3) onto the
the sealant container). This can
connector of the sealant bottle (2).
OAE066014
increase the risk of tire failure.
3. Insert the sealant bottle into the
Detach the speed restriction
housing of the compressor (5) so
label (1) from the sealant bottle
that the bottle is upright.
6
(2), and place it in a highly visi-
WARNING
4. Ensure that the button (9) on the
ble place inside the vehicle
compressor is not pressed.
such as on the steering wheel
• Keep out of reach of children.
to remind the driver not to drive
• Avoid contact with eyes.
too fast.
• Do not swallow.
1. Shake the sealant bottle (2).
6-29
What to do in an emergency
CAUTION
Securely install the sealant fill-
ing hose to the valve. If not,
sealant may flow backward,
possibly clogging the filling
hose.
OAE067040
OAEPH067016
5. Unscrew the valve cap from the
7. Plug the compressor power cord
valve of the defective wheel and
(4) into the vehicle power outlet.
screw the filling hose (3) of the
8. With the vehicle ON (
indica-
sealant bottle onto the valve.
tor ON), switch on the compressor
6. Ensure that the compressor is
and let it run for approximately
switched OFF.
OAE066027
5~7 minutes to fill the sealant up
to proper pressure. (refer to the
Tire and Wheels, chapter 8). The
inflation pressure of the tire after
filling is unimportant and will be
checked/corrected later.
Be careful not to overinflate the
tire and stay away from the tire
when filling it.
6-30
Checking the tire inflation pres-
CAUTION
sure
1. After driving approximately
4~6
Do not attempt to drive your
miles
(7~10 km or about
vehicle if the tire pressure is
10 minutes), stop at a safe loca-
below 29 psi
(200 kpa). This
tion.
could result in an accident due
to sudden tire failure.
9. Switch off the compressor.
10. Detach the hoses from the
OLMF064106
sealant bottle connector and
from the tire valve.
Distributing the sealant
Return the Tire Mobility Kit to its stor-
11. Immediately drive approximately
age location in the vehicle.
4~6 miles (7~10 km or about 10
minutes) to evenly distribute the
sealant in the tire.
WARNING
6
Do not exceed a speed of 50 mph
OAEPH067041
Do not the filling leave your
(80 km/h). If possible, do not fall
2. Connect the filling hose (3) direct-
below a speed of 12 mph (20 km/h).
vehicle running in a poorly ven-
ly into the compressor.
tilated area for extended peri-
While driving, if you experience any
ods of time. Carbon monoxide
unusual vibration, ride disturbance or
poisoning and suffocation can
noise, reduce your speed and drive
occur.
with caution until you can safely pull
off of the side of the road.
6-31
What to do in an emergency
5. Adjust the tire inflation pressure to
CAUTION
the recommended tire inflation.
With the ignition switched on, pro-
When you use the Tire Mobility Kit
ceed as follows.
including sealant not approved by
- To increase the inflation pres-
HYUNDAI, the tire pressure sen-
sure:
sors may be damaged by sealant.
Switch on the compressor. To
The sealant on the tire pressure
check the current inflation pres-
sensor and wheel should be
sure setting, briefly switch off the
removed when you replace the
compressor.
tire with a new one and inspect
- To reduce the inflation pres-
the tire pressure sensors at an
OAE067040
sure:
authorized dealer.
3. Connect the other end of the filling
Press the button (9) on the com-
hose (3) directly into the tire valve.
pressor.
4. Plug the compressor power cord
WARNING
(4) into the vehicle power outlet.
i
Information
The tire inflation pressure must
The pressure gauge may show higher
be at least 32 psi (220 kPa). If it
than actual reading when the com-
is not, do not continue driving.
pressor is running. To get an accurate
Call for road side service or
tire pressure, the compressor needs to
towing.
be turned off.
i
Information
When reinstalling the repaired or
replaced tire and wheel on the vehicle,
tighten the wheel lug nut to 79~94
lbf·ft (11~13 kgf·m).
6-32
With Tire Mobility Kit (TMK)
The Tire Mobility Kit is a temporary fix
WARNING
- Type B
to the tire and the tire should be
inspected by an authorized HYUNDAI
Temporary fix
dealer as soon as possible.
Have your tire repaired as soon
as possible. The tire may lose
CAUTION
air pressure at any time after
One sealant bottle for one tire
inflating with the Tire Mobility
Kit.
When two or more tires are flat,
do not use the tire mobility kit
because the supported one
sealant of Tire Mobility Kit is
only used for one flat tire.
OAEPH067008
For safe operation, carefully read
WARNING
and follow the instructions in this
manual before use.
6
Tire wall
(1) Compressor
Do not use the Tire Mobility Kit
(2) Sealant bottle
to repair punctures in the tire
walls. This can result in an acci-
dent due to tire failure.
6-33
What to do in an emergency
Introduction
The Tire Mobility Kit is not designed
•
When the tire and wheel are dam-
or intended as a permanent tire
aged, do not use Tire Mobility Kit
With the Tire Mobility Kit you stay
repair method and is to be used for
for your safety.
mobile even after experiencing a tire
one tire only.
puncture.
•
Use of the Tire Mobility Kit may not
This instruction shows you step by
be effective for tire damage larger
The compressor and sealing com-
step how to temporarily seal the
than approximately
0.24 inch
(6
pound system effectively and com-
puncture simply and reliably.
mm).
fortably seals most punctures in a
passenger car tire caused by nails
Read the section "Notes on the safe
Please contact the nearest
or similar objects and reinflates the
use of the Tire Mobility Kit".
HYUNDAI dealership if the tire
tire.
cannot be made roadworthy with
the Tire Mobility Kit.
After you ensure that the tire is prop-
Notes on the safe use of the
erly sealed you can drive cautiously
•
Do not use the Tire Mobility Kit if a
Tire Mobility Kit
on the tire (distance up to 120 miles
tire is severely damaged by driving
• Park your car at the side of the
(200 km)) at a max. speed of (50
run flat or with insufficient air pres-
road so that you can work with the
mph (80 km/h)) in order to reach a
sure.
Tire Mobility Kit away from moving
service station or tire dealer for the
•
Do not remove any foreign objects
traffic.
tire replacement.
such as nails or screws that have
• To be sure your vehicle will not
It is possible that some tires, espe-
penetrated the tire.
move, even when you're on fairly
cially with larger punctures or dam-
•
Provided the car is outdoors, leave
level ground, always set your park-
age to the sidewall, cannot be sealed
the engine running. Otherwise
ing brake.
completely.
operating the compressor may
• Only use the Tire Mobility Kit for
Air pressure loss in the tire may
eventually drain the car battery.
sealing/inflation passenger car
adversely affect tire performance.
•
Never leave the Tire Mobility Kit
tires. Only punctured areas located
For this reason, you should avoid
unattended while it is being used.
within the tread region of the tire
abrupt steering or other driving
can be sealed using the tire mobil-
•
Do not leave the compressor run-
maneuvers, especially if the vehicle
ity kit.
ning for more than 10 minutes at a
is heavily loaded or if a trailer is in
time or it may overheat.
• Do not use on motorcycles, bicy-
use.
cles or any other type of tires.
6-34
•
Do not use the Tire Mobility Kit if
Components of the Tire Mobility Kit
the ambient temperature is below
-22°F (-30°C).
•
In case of skin contact with the-
sealant, wash the area thoroughly-
with plenty of water.If the irritation-
persists, seek medical attention.
•
In case of eye contact with the
sealant,flush your eyes for at least
15 min-utes.If the irritation persists,
seekmedical attention.
•
In case of swallowing the
sealant,rinse the mouth and drink
plenty ofwater.However, never give
anythingto an unconscious person
and seekmedical attention immedi-
ately.
6
•
Long time exposure to the sealant-
may cause damage to bodily tis-
suesuch as kidney, etc.
ODE067044
1. Speed restriction label
5. Holder for the sealant bottle
2. Sealant bottle and label with
6. Compressor
speed restriction
7. ON/OFF switch
3. Filling hose from sealant bottle to
8. Pressure gauge for displaying the
wheel
tire inflation pressure
4. Connectors and cable for power
9. Button for reducing tire inflation
outlet direct connection
pressure
6-35
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст