Hyundai Coupe (2008 year). Manual — part 14
DO-IT-YOURSELF MAINTENANCE
6
POWER STEERING FLUID
25
LEVEL
G220B01A-AAT
G230A01GK-GAT
NOTE:
Checking Engine Cooling Fan
o Grinding noise from the power
The engine coolant fan should come
steering pump may be heard im-
on automatically if the engine coolant
mediately after the engine is
temperature is high.
started in extremely cold condi-
tions (below - 20°C). If the noise
stops during warm up, there is
no abnormal function in the sys-
G220C01A-AAT
tem. It is due to a power steering
Checking Condenser Cooling
fluid characteristic in extremely
Fan
cold conditions.
The condenser coolant fan should
o Do not start the engine when the
HGK5011
come on automatically whenever the
power steering oil reservoir is
The power steering fluid level should
air conditioning is in operation.
empty.
be checked regularly.
To check the power steering fluid
level, be sure the ignition is "OFF",
then check to make certain that the
power steering fluid level is between
the "MAX" and "MIN" level markings
on the fluid reservoir.
6 DO-IT-YOURSELF MAINTENANCE
HEADLIGHT AIMING ADJUSTMENT
26
G240A01A-AAT
G290A02GK-GAT
1. Keep all tires inflated to the correct
Power Steering Hoses
pressure.
2. Place the vehicle on level ground
It is suggested that you check the
and press the front bumper & rear
power steering hose connections for
bumper down several times. Place
fluid leakage daily. The power steer-
vehicle at a distance of 3m (118
ing hoses should be replaced if there
in.) from the test wall.
is severe surface cracking, pulling,
scuffing or worn spots. Deterioration
3. See that the vehicle is unloaded
(except for full levels of coolant,
of the hose could cause premature
Horizontal
engine oil and fuel, and spare tire,
failure.
aiming
jack, and tools).
4. Clean the head light lenses and
OGK076068N
turn on the headlights.
5. Open the hood.
6. Draw the vertical line (through the
center of each headlight beam pat-
tern) and the horizontal line (through
Vertical aiming
the center of each headlight beam
pattern) on the aiming screen.
And then, draw a parallel line at 30
mm (1.18 in.) under the horizontal
line.
7. Adjust each cut-off line of the low
beam to the parallel line with a
OGK076067N
phillips screwdriver
- VERTICAL
Before performing aiming adjustment,
AIMING.
make sure of the following.
8. Adjust each cut-off line of the low
beam to each vertical line with a
phillips screwdriver
- HORIZON-
TAL AIMING.
DO-IT-YOURSELF MAINTENANCE
6
REPLACEMENT OF LIGHT
27
BULBS
G290B02GK-GAT
G260A01MC-AAT
SPECIFICATION:
Adjustment After Headlight As-
"H"
Before attempting to replace a light
sembly Replacement
Horizontal center line of headlights
bulb, be sure the switch is turned to
Vertical line
from ground:
the "OFF" position.
30mm (1.18 in.)
Low Beam: 690 mm (27.2 in.)
The next paragraph shows how to
Horizontal line
W
High Beam: 674 mm (26.5 in.)
reach the light bulbs so they may be
"P"
changed. Be sure to replace the burned-
"W"
out bulb with one of the same number
Distance between each headlight cen-
and wattage rating.
H
ter :
See page 6-36 for the wattage descrip-
Cut-off line
Low Beam: 1,336 mm (52.6 in.)
tions.
Ground
High Beam: 1,098 mm (43.2 in.)
L
line
H
"L"
!
G290B01HR-1
CAUTION:
Distance between the headlights and
o Keep the lamps out of contact
If the vehicle has had front body repair
the wall that the lights are tested
with petroleum products, such as
and the headlight assembly has been
against : 3,000 mm (118 in.)
oil, gasoline, etc.
replaced, the headlight aiming should
o If you don't have necessary tools,
be checked using an aiming screen as
the correct bulbs and the exper-
shown in the illustration. Turn on the
tise, consult your authorized
headlight switch.
Hyundai dealer.
1. Adjust headlights so that main axis
of light is parallel to center line of
the body and is aligned with point
"P" shown in the illustration.
2. Dotted lines in the illustration show
the center of headlights.
6 DO-IT-YOURSELF MAINTENANCE
28
G270A01GK-AAT
Headlight and Front Turn Signal
Light
1. Allow the bulb to cool. Wear eye
protection.
2. Open the engine hood.
3. Always grasp the bulb by its plastic
base, avoid touching the glass.
OGK076047
OGK076049
5. Turn the plastic cover counterclock-
7. Push the bulb spring to remove the
wise and remove it.
headlight bulb.
OGK076066N
4. Disconnect the power cord from the
bulb base in the back of the head-
light.
OGK076048
OGK076050
6. Disconnect the connector from the
8. Remove the protective cap from
bulb base in the back of the head-
the replacement bulb and install
light.
the new bulb by matching the plas-
DO-IT-YOURSELF MAINTENANCE
6
29
tic base with the headlight hole.
G270K01CM-GAT
Reattach the bulb spring and re-
Front Fog Light (If Installed)
connect the connector.
NOTE:
9. Use the protective cap and carton
It is recommended that the front fog
to promptly dispose of the old bulb.
light bulb be replaced by an autho-
10.Check for proper headlight aim.
rized Hyundai dealer.
G270A03O
G270B01GK-GAT
!
Rear Combination Light
WARNING:
(Without woofer speaker)
This halogen bulb contains gas
under pressure and if impacted
OGK076052
could shatter, resulting in flying
fragments. Always wear eye pro-
11.To replace the front turn signal light
tection when servicing the bulb.
bulb, remove from the bulb holder
(2)
(1)
Protect the bulb against abrasions
and install the new bulb.
or scratches and against liquids
when lighted. Turn the bulb on
(3)
(1)
only when installing in a head-
light. Replace the headlight if dam-
aged or cracked. Keep the bulb
out of the reach of children and
OGK076037
dispose of the used bulb with care.
1. Open the tail gate.
6 DO-IT-YOURSELF MAINTENANCE
30
5. To replace the rear combination light
(stop/tail light, turn signal light, back-
up light) take it out from the bulb
holder by turning it counterclock-
wise.
6. Install the new bulb.
(1) Stop/Tail light
(2) Back-up light
(3) Turn signal light
OGK076040
OGK076042
2. To remove the cover of the rear
4. To detach the rear combination light
luggage trim, turn the knob by hand
hit it strongly by hand.
to the counterclockwise.
OGK076041
3. Remove the nut (8mm) with a span-
ner.
DO-IT-YOURSELF MAINTENANCE
6
31
G275B01GK-GAT
Rear Combination Light
(With woofer speaker)
(2)
(1)
(3)
(1)
OGK076039
OGK076040
3. Extract the mounting screws
5. To remove the cover of the rear
(10mm) around the woofer speaker
luggage trim, turn the knob by hand
OGK076037
with a spanner.
to the counterclockwise.
4. Disconnect the power cord from the
1. Open the tail gate.
woofer speaker.
OGK076041
6. Remove the nut
(8mm) with a
HGK5038
wrench.
2. Take off the luggage board.
6 DO-IT-YOURSELF MAINTENANCE
32
8. To replace the rear combination light
G270F02A-GAT
(stop/tail light, back-up light, turn
Rear Fog Light (If Installed)
signal light), take it out from the
bulb holder by turning it counter-
clockwise.
9. Install the new bulb.
OGK076042
7. To detach the rear combination light
OGK066100L
hit it strongly by hand.
1. Remove the mounting screws of the
rear fog light cover with a phillips
screwdriver.
2. Disconnect the power cord by turn-
ing the bulb cover counterclockwise
and take the bulb out from the bulb
cover by turning it clockwise.
3. Replace with a new bulb.
DO-IT-YOURSELF MAINTENANCE
6
33
G270C01GK-AAT
Luggage Compartment Light
HGK5046
HTB284
3. Disconnect the power cord.
4. Replace with a new bulb.
HGK5045
1. Open the tail gate.
2. Remove the cover with a flat-blade
screwdriver.
6 DO-IT-YOURSELF MAINTENANCE
34
G270G01GK-AAT
G270H01GK-GAT
Map Light
Glove Box Illuminated Light
OGK076022
3. Remove the glove box by pulling
OGK076046
OGK076020
strongly.
1. Remove the cover with a flat-blade
1. Remove the mounting screws on
screwdriver.
the downside of the glove box.
2. Replace with a new bulb.
!
CAUTION:
Be careful not to damage the glove
box when pulling the glove box.
OGK076021
2. Open the glove box and remove the
mounting screws on the upside of
the glove box.
DO-IT-YOURSELF MAINTENANCE
6
35
G270E02A-GAT
Side Repeater (If Installed)
NOTE:
It is recommended that the side
Power Cord
repeater bulb be replaced by an
authorized Hyundai dealer.
Clip
OGK076038
4. Disconnect the power cord.
5. Remove the glove box illuminated
light by pushing the clip.
6. Replace with a new bulb.
6 DO-IT-YOURSELF MAINTENANCE
BULB WATTAGE
36
G280A04GK-GAT
OGK066009L
No.
Part Name
Wattage
Socket type
No.
Part Name
Wattage
Socket type
Head Light (Low)
55
PX 26d
8
Luggage Compartment Light
5
S8.5/8.5
1
Front Position Light
5
W2.1X9.5d
High Mounted
With spoiler
2.4 (LED)
N/A
9
2
Map Light
10
W2.1×9.5D
Stop Light
Without spoiler
3.5 (LED)
-
3
Front Turn Signal Light
21
BAU15s
10
Rear
Back-up Light
16
W2.1X9.5d
4
Front Fog Light (If installed)
51
P22d
11
Combination
Turn Signal Light
21
BA15s
5
Head Light (High)
55
PX 26d
12
Stop/Tail Light
21/5
BAY15d
6
Side repeater light (If installed)
5
W2.1X9.5d
13
License Plate Light
5
W2.1X9.6d
7
Front Door Edge Warning Light
5
W2.1X9.5d
14
Rear Fog Light (If installed)
21
BA15s
DO-IT-YOURSELF MAINTENANCE
6
FUSE PANEL DESCRIPTION
37
G200C02GK-GAT
Engine Compartment
HGK4005
NOTE:
Not all fuse panel descriptions in this manual may be applicable to your vehicle. It is accurate at the time of
printing. When you inspect the fuse box on your vehicle, refer to the fuse box label.
6 DO-IT-YOURSELF MAINTENANCE
38
DESCRIPTION
FUSERATING
PROTECTED COMPONENTS
BATT
120A
Generator(1.6L/2.0L)
BATT
50A
BCM BOX(Tail lamp relay,Power connector,Fuse(2,7,12,13,19,20,24))
COND
30A
Condenser fan relay
RAD
30A
Radiator fan relay
Engine control relay, Fuel pump relay, A/T control relay,
ECU
30A
Generator,ECM(1.6L/2.7L),PCM(2.0L)
IGN
30A
Ignition switch,Start relay
ABS 1
40A
ABS/ESP control module,ESP Air bleeding connector
ABS 2
40A
ABS/ESP control module,ESP Air bleeding connector
BLOWER
30A
Blower relay
INJ
15A
Injector
SNSR
10A
Oxygen sensor,Camshaft position sensor, Idle speed control actuator
DRL
15A
DRL control module
F/FOG
15A
Front fog lamp relay
ECU
10A
TCM(2.7L),ECM(2.7L/1.6L)
HORN,A/CON
15A
Horn relay,A/C relay
H/LP (HI)
15A
Head lamp relay(High)
H/LP (LO)
15A
Head lamp relay(Low)
DO-IT-YOURSELF MAINTENANCE
6
39
G200D02GK-GAT
Inner Panel
OGK066010L
6 DO-IT-YOURSELF MAINTENANCE
40
DESCRIPTION
FUSERATING
PROTECTED COMPONENTS
IG COIL
20A
Ignition coil(1.6l/2.7L), Electronic chrome mirror
AMP
20A
AMP
B/UP LAMP
10A
Back-up lamp switch,Transaxle range switch,Cruise control module,Stop lamp switch
A/BAG IND
10A
Instrument cluster (A/BAG IND.)
A/BAG
15A
SRS control module
HTD MIR
10A
Mirror defogger
HAZARD
10A
Hazard relay
R/WIPER
15A
Rear wiper motor,Rear intermittent wiper relay
TAIL-RH
10A
Right tail lamps,Glove box lamp
F/WIPER
20A
Front wiper motor,Front wiper relay
RR DEFOG
30A
Defogger relay
STOP
15A
Stop lamp switch,Burglar alarm horn relay,Folding/Unfolding relay
TAIL-LH
10A
Left tail lamps
A/CON
10A
A/C control module, Blower relay
ECU
10A
ECM, Multi gauge unit, TCM, Vehicle speed sensor
CLUSTER
10A
Instrument cluster (Power), Per-excitation resister, DRL Control module,Generator
ROOM LP
10A
Room lamp,Clock,Audio,Data link connector,Multi gauge unit
P/WINDOW
30A
Power window relay
T/GATE
15A
Trunk lid switch
IGN
10A
AQS sensor,Head lamp relay,DRL Control module
RR FOG
10A
Rear fog lamp
C/LIGHT
15A
Cigarette lighter,Outside mirror switch
S/ROOF
15A
Sunroof,Power door lock/Unlock relay
S/HTR
20A
Seat warmer
ABS
10A
ESP/ABS control module
AUDIO
10A
Audio,Digital clock
EMISSION CONTROL SYSTEM
Emission Control System
7-2
Catalytic Converter
7-3
7
7
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст