Hyundai H350 (2016 year). Manual — part 5

Convenient features of your vehicle

Opening/closing from the

Child-protector mid sliding

Information

inside

door lock (if equipped)

Your vehicle may be equipped with a

long sliding door with an intermediate

detent.

You can also lock the sliding door in

place

around halfway when

opening/closing. If you do this, the

door does not have to be opened fully

when getting into or out of the vehicle.

The sliding door is not fully engaged

when in the intermediate detent.

To open: Slide the sliding door by

OEU044005

OEU044003

handle (1) back to the stop.

The sliding door is equipped with an

The child safety lock is provided to

Check the sliding door detent.

active retainer, which engages the

help prevent children from acciden-

The sliding door must be engaged.

door at the end stop when opened.

tally opening the mid sliding door

from inside the vehicle. The mid slid-

You can only open a sliding door

from the inside if the child-proof locks

To close: Slide the sliding door firm-

ing door safety locks should be used

have not been activated. Locking

ly forwards by handle

(1) until it

whenever children are in the vehicle.

knob (2) pops up when you open a

engages.

1.Open the sliding door.

locked door. Only this sliding door is

2.Push the child safety lock located on

unlocked. The other doors remain

the mid sliding edge of the door to

locked.

the "Lock" position. When the child

safety lock is in the "Lock

(

position, mid sliding door will not

open even though the inner door

handle is pulled inside the vehicle.

3-16

ELECTRICAL STEP (IF EQUIPPED)

3. Close the mid sliding door.

If you turn on the step switch to oper-

To open the mid sliding door, pull the

ate the electrical step, the electrical

outside door handle.

step automatically extends when the

mid sliding door is opened and

Even though the door may be

retracts when it is closed. When the

unlocked, the mid sliding door will

electrical step is either in operation

not open by pulling the inner door

or extended out, the electrical step

handle until mid sliding door child

indicator illuminates on the instru-

safety lock is unlocked.

ment cluster.

WARNING

OEU044188

Mid sliding door lock

If children accidentally open the

mid sliding door while the vehi-

cle is in motion, they could fall

out and be severely injured or

killed. To prevent children from

opening the mid sliding door

from the inside, the mid sliding

door safety lock should be used

OEU044048

whenever children are in the

Your vehicle's mid sliding door may

vehicle.

be equipped with an electrical step.

When getting in and out of the vehi-

cle, use the grab handles and electri-

cal step.

3-17

Convenient features of your vehicle

The default setting of the STEP

NOTICE

WARNING

switch is the ON position.

When the electrical step is extend-

Press the STEP switch, when the

ed out, the accelerator inter-lock

If you do not use the grab han-

electrical step is not in use in regard-

operates to block the vehicle

dle and the step, you could

less of opening/closing of the mid-

acceleration for your safety.

injure yourself when getting in

sliding door.

and out of the vehicle.

In this case, the LED indicator on the

To prevent risks:

STEP switch goes OFF.

WARNING

To use the electrical step, re-press

• Draw the passengers' atten-

Never move the shift lever,

the STEP switch. Then, the LED indi-

tion to the electrical step. Wait

when any passengers exit or

cator on the STEP switch will illumi-

until the electrical step is fully

enter the vehicle through the

nate.

extended.

mid sliding door. In this situa-

• Do not jump out of the vehi-

tion, shifting the gear out of N

cle.

Conditions to extend the electrical

(Neutral) causes the electrical

step:

step to abruptly retract and the

• Only use the grab handle and

step. Only they are designed

1) The vehicle is stopped.

passengers to fall from it, caus-

for such a load.

ing the serious body injury.

2) The shift gear is in N (Neutral).

Always make sure that all pas-

• Keep grab handles, access

3) Either the parking brake or the

sengers enter or exit the vehi-

steps and entry sills free from

foot brake is applied.

cle, before shifting the gear.

dirt, e.g. mud, clay, snow and

The electrical step automatically

ice.

retracts in from the “extending-out”

position, when the conditions 1 and 2

are unsatisfied.

3-18

Operation and obstacle detec-

Electrical step warning alarm

WARNING

tion

1.Continuous beeping sound

The electrical step (1) is equipped

Never drive your vehicle, when

You will hear this type of alarm,

with a device to detect an obstacle in

the electrical step is extended

whenever the electrical step oper-

front.

out. It may cause an accident,

ates.

When the electrical step comes into

strike with other vehicles, and

2.Short beeping sound

(short &

contact with an obstacle while

even injure passers-by. Always

repetitive)

extending out, its movement auto-

drive your vehicle with the elec-

You will hear this type of alarm,

matically stops with 'short but repeti-

trical step fully retracted in.

when the parking/foot brakes are

tive' warning alarms.

released.

To fully extend out the electrical step

In this case, apply the parking/foot

again, take the following steps. First,

brakes for your safety.

remove the obstacle. Second, close

and then re-open the mid-sliding

3.Long beeping sound (long & repet-

itive)

door. Finally, repetitively press the

STEP switch to turn OFF and turn

You will hear this type of alarm,

ON the electrical step.

when the operation of the electrical

step temporarily fails due to opera-

NOTICE

tional/electrical problems.

In this case, remove foreign sub-

If the electrical step hinders load-

stances, such as sand, mud, and

ing, you can block the step when

ice. Then, re-press the STEP

opening the sliding door by using

switch to operate the electrical

the obstruction detection. This

step.

means that the electrical step

remains retracted and a fork-lift

However, if the problem persists,

manually push in the electrical step

truck or another lifting vehicle can

move closer to the load compart-

as a safety measure. Still, we rec-

ommend you to have the electrical

ment.

step repaired by an authorized

HYUNDAI dealer.

3-19

Convenient features of your vehicle

The emergency measures,

Step does not operate, after

which you may take in case of

being extended out.

the electrical-step failures.

Hold the step in position with the R-

The step friction surface is con-

clip, as explained below. Then, turn

OFF the switch and visit a near-by

taminated with the foreign sub-

Hyundai dealer for repair services.

stances.

When you hear the warning alarm

The electrical step may not normally

while driving, you may stop the alarm

operate, when its friction surface is

by disconnecting the electrical step

contaminated. Repetitively operate

fuse located in the fuse box under

either the step switch or the mid-slid-

the left side of the driver's seat.

ing door 2-to-3 times. When the step

OEU044078

operation completely stops for the

Hold the step in position with the

same reason, manually push in the

R-clip

step and turn OFF the switch.

Remove the foreign substances with

1. Pull R-clips (3) on both rods (1) on

washing equipment at a vehicle

the underside of the step out of

wash (Refer to the regular cleaning

their respective pins. Remove

in the chapter 3). Then, turn ON the

washers (2) and detach both rods

step switch, and operate the mid-

(1).

sliding door. When the electrical step

does not still normally operate, we

recommend that the electrical step

be checked by an authorized

HYUNDAI dealer.

3-20

Regular cleaning

Upper entrance

Electric step

side rail

Lower entrance

OEU044079

OEU044226

2. Fold rods (1) into the housing in

3. Insert R-clips (2) into the step as

OEU044077

the step.

far as they will go through the

holes on both sides of the hous-

Steps should be cleaned at least

Push the step into its housing

ing.

once per month and more often if

conditions dictate.

The step is secured in its housing.

By using a power hose or even a

standard hose frequently ensure no

NOTICE

build up of material inside the step.

When securing the step for the

The step will “self-clean” if the mud

first time, you must pierce a film

and dirt is lubricated with a power

with the spring cotters.

wash.

Remember to clean not just the tread

(the bit you stand on) but the side of

the step too.

3-21

Convenient features of your vehicle

REAR DOOR (IF EQUIPPED)

After cleaning the step should be

WARNING

allowed to dry. When dry, a day or

two later perhaps, apply silicons

If you open a rear door, you

The rear lights will be covered if

spray to help lubricate the movement

could:

you open the rear doors to the

of the step.

90° detent position.

• endanger other people or road

Do not use grease. Avoid use of oil, it

users

The vehicle will then be unsafe

will simply wash away.

• be caught by oncoming traffic.

as its rear lights will not be vis-

If the conditions are particularly bad

ible for approaching traffic.

daily cleaning may be required.

This is particularly the case if

Other road users may not real-

you open the rear door more

Failure to clean the step regularly or

ize until too late that it is an

than 90°. There is a risk of an

to service the steps may result in the

obstruction. This could lead to

accident and injury.

failure of the step in service. This will

an accident.

not be covered under warranty.

Only open the rear doors when

You should ensure that the

traffic conditions permit.

We recommend that mud flaps are

vehicle is visible from the rear

fitted to your vehicle.

Always make sure that the rear

in accordance with the relevant

door is properly locked.

national regulations, by using

the warning triangle for

instance.

CAUTION

Make sure that there is suffi-

cient clearance when opening

the rear doors. You could other-

wise damage the vehicle and

objects in close range of the

rear doors.

3-22

Opening/closing from the out-

Opening/closing from the

To unlock: Slide latch

(2) to the

side

inside

right. You will see a allow mark.

Opening the right-hand rear

door

To open: Pull opening lever (1) up

and open the rear door.

NOTICE

Unlock

Lock

Latch (2) slides to the right when

you open a locked rear door from

the inside. The white section is

visible. Only the rear door

unlocks. The other doors remain

locked.

OEU044006

To close: Make sure that the left-

OEU044010

Opening the right-hand rear

hand rear door is closed.

door

Pull handle (1) .

Pull the rear door firmly by the door

Release the lever on the inside of the

Swing the rear door to the side until

handle to close it.

right rear door.

it engages.

NOTICE

To lock: Slide latch (2) to the left.

You can only open the locked rear

doors from the inside if the child-

proof locks have not been activat-

ed.

3-23

Convenient features of your vehicle

Opening the left-hand rear

Opening the rear doors to an

door

angle of 180° or 270°

(if equipped)

OEU044054

With the rear door opened to an

angle of 270°, push it against mag-

OEU044007

netic door retainer (2) on the side

OEU044053

Make sure that the right-hand rear

wall.

door is open and engaged.

Open the rear door to about 45°.

When the magnet on the rear door is

Push release handle (1) in the direc-

Pull and hold door retainer (1) in the

in contact with magnetic door retain-

tion of the arrow.

direction of the arrow.

er (2) , the rear door is held in this

Swing the rear door to the side until

Open the rear door more than 90°,

position.

it engages.

so that the door retainer cannot

engage.

Release the door retainer and open

the door to an angle of 180° or 270°.

3-24

NOTICE

Child-protector rear door lock

3. Close the rear door.

(if equipped)

To open the rear door, pull the out-

Vehicles with 270° pivoting rear

side door handle.

doors:

Even though the door may be

If door retainer

(1) malfunctions

unlocked, the rear door will not open

while loading, you can swivel it

by pulling the inner door handle until

180° against the spring force and

rear door child safety lock is

Lock

onto the door and engage it. The

unlocked.

door retainer remains in this posi-

tion and will not swivel back to its

WARNING

original position.

Before closing the door, release

Rear door lock

Unlock

door retainer (1) from the detent

If children accidentally open the

and return it to its original posi-

OEU044073

rear door while the vehicle is in

tion.

The child safety lock is provided to

motion, they could fall out and

help prevent children from acciden-

be severely injured or killed. To

Closing the rear doors from

prevent children from opening

tally opening the rear door from

the outside (if equipped)

the rear door from the inside,

inside the vehicle. The rear door

safety locks should be used whenev-

the rear door safety lock should

Pull the rear door away from mag-

netic door retainer.

er children are in the vehicle.

be used whenever children are

in the vehicle.

Close the left-hand rear door firmly

1.Open the rear door.

from the outside.

2.Turn the child safety lock located on

the rear edge of right side door to

the "Lock" position. When the child

safety lock is position, rear door will

not open even though the inner door

handle is pulled inside the vehicle.

3-25

Convenient features of your vehicle

WINDOWS

(1) Driver's door unlock/lock switch

(2) Automatic power window up */

down switch (Driver's side)

(3) Automatic power window down

switch (Driver's side)

(4) Passenger's door unlock /

lock switch

(5) Automatic power window

down switch (Passenger's side)

(6) Rear seat window (Type A)

(7) Rear seat window (Type B)

*: if equipped

Information

In cold and wet climates, power win-

dows may not work properly due to

■ Type A (if equipped)

■ Type B (if equipped)

freezing conditions.

OEU045046/OEU044080/OEU044014

3-26

Power windows

Window opening and closing

Auto down window

The ignition switch must be in the ON

position for power windows to oper-

ate. Each door has a power window

switch that controls the door's win-

dow. The driver has a power window

lock switch which can block the oper-

ation of front passenger windows.

The power windows can be operated

for approximately 30 seconds after

the ignition key is removed or turned

to the ACC or LOCK position.

However, if the front doors are

OEU044044

OEU044012

opened, the power windows cannot

To open or close a window, press

Pressing the power window switch

be operated even within the 30 sec-

down or pull up the front portion of

momentarily to the second detent

onds period.

the corresponding switch to the first

position

(3) completely lowers the

detent position (2).

driver's window even when the

switch is released. To stop the win-

dow at the desired position while the

window is in operation, pull up the

switch momentarily to the opposite

direction of the window movement.

3-27

Convenient features of your vehicle

Auto up/down window

1.Turn the ignition switch to the ON

(if equipped) (Driver's window)

position.

2.Close the driver's window and con-

tinue pulling up the driver's power

window switch for at least 1 second

after the window is completely

closed.

OEU034028

Automatic reversal (if equipped)

OEU044013

If the upward movement of the win-

dow is blocked by an object or part of

Pressing or pulling up the power win-

the body, the window will detect the

dow switch momentarily to the sec-

resistance and will stop upward

ond detent position

(3) completely

movement. The window will then

lowers or lifts the window even when

lower approximately 30 cm (11.8 in.)

the switch is released. To stop the

to allow the object to be cleared.

window at the desired position while

the window is in operation, pull up or

If the window detects the resistance

press down and release the switch.

while the power window switch is

pulled up continuously, the window

If the power window does not oper-

will stop upward movement then

ate normally, the automatic power

lower approximately 2.5 cm (1 in.).

window system must be reset as fol-

lows:

3-28

And if the power window switch is

Rear seat window

pulled up continuously again within 5

(Type A, if equipped)

(Type B, if equipped)

seconds after the window is lowered

by the automatic window reversal

feature, the automatic window rever-

sal will not operate.

Information

The automatic reverse feature for the

driver's window is only active when

the "auto up" feature is used by fully

pulling up the switch. The automatic

reverse feature will not operate if the

window is raised using the halfway

OEU044080

OEU044014

position on the power window switch.

To open the window, move the win-

To open the windows, pull the rear

dow while pressing the handle the

portion of the latch out. Swing the

WARNING

direction of the arrow.

latch forward and out, then lock it into

the open position by pushing out-

Always check for obstructions

ward until you hear a click. To close

before raising any window to

the windows, pull the handle inward.

avoid injuries or vehicle dam-

Then push the handle rearward until

age. If an object less than 4 mm

you hear a click.

(0.16 in.) in diameter is caught

between the window glass and

NOTICE

the upper window channel, the

automatic reverse window may

In cold and wet climates, rear

not detect the resistance and

quarter panel windows may not

will not stop and reverse direc-

work properly due to freezing con-

tion.

ditions.

3-29

Convenient features of your vehicle

HOOD

Opening the hood

OEU044036

OEU044016

2.Go to the front of the vehicle, raise

3.Pull out the support rod.

OEU044015

the hood slightly, pull the second-

4.Hold the hood opened with the

1.Pull the release lever to unlatch the

ary latch

(1) inside of the hood

support rod.

hood. The hood should pop open

center and lift the hood (2).

slightly.

WARNING

Hot parts

Open the hood after turning off

Grasp the support rod in the

the engine on a flat surface,

area wrapped in plastic. The

shifting the shift lever to

plastic will help prevent you

R(Reverse) for manual trans-

from being burned by hot metal

mission, and setting the parking

when the engine is hot.

brake.

3-30

Closing the hood

WARNING

1.Before closing the hood, check the

following:

Hood

•

Always double check to be

• All filler caps in engine compart-

sure that the hood is firmly

•

Before closing the hood,

ment must be correctly installed.

latched before driving away. If

ensure that all obstructions

it is not latched, the hood

• Gloves, rags or any other com-

are removed from the hood

could fly open while the vehi-

bustible material must be

opening. Closing the hood

cle is being driven, causing a

removed from the engine com-

with an obstruction present in

total loss of visibility, which

partment.

the hood opening may result

might result in an accident.

2.Return the support rod to its clip to

in property damage or severe

•

The support rod must be

prevent it from rattling.

personal injury.

inserted completely into the

3.Lower the hood until it is about 30

•

Do not leave gloves, rags or

hole whenever you inspect

cm (1 ft.) above the closed position

any other combustible materi-

the engine compartment. This

and let it drop. Make sure that it

al in the engine compartment.

will prevent the hood from

locks into place.

Doing so may cause a heat-

falling and possibly injuring

induced fire.

you.

•

Do not move the vehicle with

the hood raised. The view will

be blocked and the hood

could fall or be damaged.

3-31

Convenient features of your vehicle

FUEL FILLER LID

■ Driver’s side

Closing the fuel filler lid

WARNING

1.To install the cap, turn it clockwise

until it "clicks". This indicates that

Refueling

the cap is securely tightened.

•

If pressurized fuel sprays out,

2.Close the fuel filler lid and push it

it can cover your clothes or

lightly and make sure that it is

skin and thus subject you to

securely closed.

the risk of fire and burns.

Always remove the fuel cap

Information

carefully and slowly. If the cap

is venting fuel or if you hear a

If the fuel-filler lid does not open

OEU044017

hissing sound, wait until the

because ice has formed around it, tap

condition stops before com-

Open the driver's door, before open-

lightly or push on the lid to break the

pletely removing the cap.

ing the fuel filler lid

ice and release the lid. Do not pry on

the lid. If necessary, spray around the

•

Do not "top off" after the noz-

1.Stop the engine

lid with an approved de-icer fluid (do

zle automatically shuts off

2.Fully open the fuel filler lid (1) by

not use radiator anti-freeze) or move

when refueling.

pulling it out.

the vehicle to a warm place and allow

•

Always check that the fuel cap

3.Turn the fuel tank cap in the coun-

the ice to melt.

is installed securely to pre-

terclockwise direction to open it.

vent fuel spillage in the event

4.Refuel the vehicle.

of an accident.

3-32

Была ли эта страница вам полезна?

Да!Нет

2 посетителя считают эту страницу полезной.

Hyundai H350 (2016 year). Manual — part 5

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.