Hyundai ix35 (2016 year). Manual — part 12
Features of your vehicle
OLM049102/H
Glove box lamp (if equipped)
The glove box lamp comes on when the
glove box is opened.
The parking lights or headlights must be
ON for the glove box lamp to function.
4 112
Features of your vehicle
DEFROSTER
■ Type A
To activate the rear window defroster,
CAUTION
press the rear window defroster button
To prevent damage to the conduc-
located in the centre facia switch panel.
tors bonded to the inside surface of
The indicator on the rear window
the rear window, never use sharp
defroster button illuminates when the
instruments or window cleaners
defroster is ON.
containing abrasives to clean the
If there is heavy accumulation of snow on
window.
the rear window, brush it off before oper-
ating the rear defroster.
The rear window defroster automatically
✽ NOTICE
turns off after approximately 20 minutes
OLM049110
If you want to defrost and defog on the
or when the ignition switch is turned off.
■ Type B
front windscreen, refer to “Windscreen
To turn off the defroster, press the rear
Defrosting and Defogging” in this sec-
window defroster button again.
tion.
OLM049109
Rear window defroster
The defroster heats the window to
remove frost, fog and thin ice from the
interior and exterior of the rear window,
whilst engine is running.
4 113
Features of your vehicle
Outside mirror defroster
(if equipped)
If your vehicle is equipped with the out-
side mirror defrosters, they will operate at
the same time you turn on the rear win-
dow defroster.
OLM049104R
Wiper deicer (if equipped)
Without smart key
The engine must be running to enable
this feature. To activate the front wiper
deicer, press the front wiper deicer but-
ton. The indicator on the button illumi-
nates when the deicer is ON.
The front wiper deicer automatically
turns off after 20 minutes or when the
ignition switch is turned off. To turn off the
deicer, press the front wiper deicer but-
ton again.
With smart key
If your vehicle is equipped with the wiper
deicer, it will operate at the same time
you turn on the rear window defroster.
4 114
Features of your vehicle
MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)
■ Type A
1. Fan speed control knob
2. MAX defroster button (Front windscreen
defroster)
3. MAX A/C selection button (if equipped)
4. Temperature control knob
5. Air conditioning button (if equipped)
6. Mode selection button
7. Air intake control button
■ Type B
CAUTION
Operating the blower when the igni-
tion switch is in the ON position
could cause the battery to dis-
charge. Operate the blower when
the engine is running.
OEL049111/OEL049111U
4 115
Features of your vehicle
Heating and air conditioning
1. Start the engine.
2. Set the mode to the desired position.
For improving the effectiveness of
heating and cooling;
- Heating:
- Cooling:
3. Set the temperature control to the
desired position.
4. Set the air intake control to the outside
(fresh) air position.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn the
air conditioning system (if equipped)
on.
OEL049120R
4 116
Features of your vehicle
Face-Level (B, D)
Air flow is directed toward the upper body
and face. Additionally, each outlet can be
controlled to direct the air discharged
from the outlet.
Floor-Level (C, E, A, D)
Most of the air flow is directed to the
OEL049112
floor.
OEL049113
Mode selection
MAX A/C-Level (B, D) (if equipped)
The mode selection buttons controls the
Defrost-Level (A, D)
The MAX A/C mode is used to cool the
direction of the air flow through the venti-
inside of the vehicle faster.
lation system.
Air flow is directed toward the upper body
Most of the air flow is directed to the
If you push the button once, the corre-
windscreen.
and face.
sponding switch will turn on, and if you
In this mode, the air conditioning and the
push the button again, the switch will turn
recirculated air position will be selected
off.
Also you may select 2~3 modes at the
automatically.
same time for desired air flow.
- face (
) + floor (
) mode
Defrost-Level (A, D)
- face (
) + defrost (
) mode
Most of the air flow is directed to the
- floor (
) + defrost (
) mode
windscreen with a small amount of air
- face (
) + floor (
) + defrost (
)
directed to the side window defroster.
mode
4 117
Features of your vehicle
OEL049114R
OEL049115
OEL049116
Instrument panel vents
Temperature control
Air intake control
The outlet vents can be opened or closed
The temperature control knob allows you
The air intake control is used to select
separately using the thumbwheel.
to control the temperature of the air flow-
the outside (fresh) air position or recircu-
Also, you can adjust the direction of air
ing from the ventilation system. To
lated air position.
delivery from these vents using the vent
change the air temperature in the pas-
To change the air intake control position,
control lever as shown.
senger compartment, turn the knob to
press the control button.
the right position for warm and hot air or
left position for cooler air.
4 118
Features of your vehicle
Recirculated air position
With the recirculated
WARNING
air position selected,
•
Continue using the climate con-
air from the passenger
trol system in the recirculated air
compartment will be
position may allow humidity to
drawn through the
increase inside the vehicle which
heating system and
may fog the glass and obscure
heated or cooled
visibility.
according to the func-
•
Do not sleep in a vehicle with the
tion selected.
air conditioning or heating sys-
tem on. It may cause serious
Outside (fresh) air position
harm or death due to a drop in the
oxygen level and/or body temper-
OEL049117
With the outside (fresh)
air position selected,
ature.
Fan speed control
air enters the vehicle
•
Continue using the climate con-
The ignition switch must be in the ON
from outside and is
trol system in the recirculated air
position for fan operation.
heated or cooled
position can cause drowsiness or
The fan speed control knob allows you to
according to the func-
sleepiness, and loss of vehicle
control the fan speed of the air flowing
tion selected.
control. Set the air intake control
from the ventilation system. To change
to the outside (fresh) air position
the fan speed, turn the knob to the right
as much as possible whilst driv-
for higher speed or left for lower speed.
✽ NOTICE
ing.
Setting the fan speed control knob to the
Prolonged operation of the heater in the
“0” position turns off the fan.
recirculated air position
(without air
conditioning selected) may cause fogging
of the windscreen and side windows and
the air within the passenger compart-
ment may become stale.
In addition, prolonged use of the air con-
ditioning with the recirculated air posi-
tion selected will result in excessively dry
air in the passenger compartment.
4 119
Features of your vehicle
System operation
Ventilation
1. Set the mode to the
position.
2. Set the air intake control to the outside
(fresh) air position.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
OYFA043118A
OEL049118
1. Set the mode to the
position.
To turn off the blowers
Air conditioning (if equipped)
2. Set the air intake control to the outside
To turn off the blowers, turn the fan
Press the A/C button to turn the air con-
(fresh) air position.
speed control knob to the "0" position.
ditioning system on (indicator light will
3. Set the temperature control to the
illuminate). Press the button again to turn
desired position.
the air conditioning system off.
4. Set the fan speed control to the
desired speed.
5. If dehumidified heating is desired, turn
the air conditioning system
(if
equipped) on.
• If the windscreen fogs up, set the mode
to the
or
position.
4 120
Features of your vehicle
Operation Tips
Air conditioning (if equipped)
✽ NOTICE
•
To keep dust or unpleasant fumes from
HYUNDAI Air Conditioning Systems are
•
When using the air conditioning sys-
entering the vehicle through the venti-
filled with R-134a refrigerant.
tem, monitor the temperature gauge
lation system, temporarily set the air
1. Start the engine. Push the air condi-
closely whilst driving up hills or in
intake control to the recirculated air
tioning button.
heavy traffic when outside tempera-
position. Be sure to return the control
2. Set the mode to the
position.
tures are high. Air conditioning sys-
to the fresh air position when the irrita-
3. Set the air intake control to the outside
tem operation may cause engine over-
tion has passed to keep fresh air in the
heating. Continue to use the blower
air or recirculated air position.
vehicle. This will help keep the driver
fan but turn the air conditioning sys-
4. Adjust the fan speed control and tem-
alert and comfortable.
tem off if the temperature gauge indi-
perature control to maintain maximum
•
Air for the heating/cooling system is
cates engine overheating.
comfort.
drawn in through the grilles just ahead
•
When opening the windows in humid
• When maximum cooling is desired, set
of the windscreen. Care should be
weather air conditioning may create
the temperature control to the extreme
taken that these are not blocked by
water droplets inside the vehicle.
left position (press the MAX A/C posi-
leaves, snow, ice or other obstructions.
Since excessive water droplets may
tion selection button (if equipped)) then
•
To prevent interior fog on the wind-
cause damage to electrical equipment,
set the fan speed control to the highest
screen, set the air intake control to the
air conditioning should only be used
speed.
fresh air position and fan speed to the
with the windows closed.
desired position, turn on the air condi-
tioning system, and adjust the temper-
ature control to desired temperature.
4 121
Features of your vehicle
Air conditioning system operation tips
•
When using the air conditioning sys-
•
If the vehicle has been parked in direct
tem, you may notice clear water drip-
Outside air
sunlight during hot weather, open the
ping (or even puddling) on the ground
windows for a short time to let the hot
under the passenger side of the vehi-
Recirculated
air inside the vehicle escape.
cle. This is a normal system operation
air
characteristic.
•
To help reduce moisture inside of the
windows on rainy or humid days,
•
Operating the air conditioning system
decrease the humidity inside the vehi-
in the recirculated air position provides
cle by operating the air conditioning
maximum cooling, however, continual
system.
operation in this mode may cause the
Blower
•
During air conditioning system opera-
air inside the vehicle to become stale.
Heater core
Climate control
Evaporator
tion, you may occasionally notice a
•
During cooling operation, you may
air filter
core
slight change in engine speed as the
occasionally notice a misty air flow
1LDA5047
air conditioning compressor cycles.
because of rapid cooling and humid air
Climate control air filter
This is a normal system operation
intake. This is a normal system opera-
(if equipped)
characteristic.
tion characteristic.
The climate control air filter installed
•
Use the air conditioning system every
behind the glove box filters the dust or
month only for a few minutes to ensure
other pollutants that come into the vehi-
maximum system performance.
cle from the outside through the heating
and air conditioning system. If dust or
other pollutants accumulate in the filter
over a period of time, the air flow from the
air vents may decrease, resulting in
moisture accumulation on the inside of
the windscreen even when the outside
(fresh) air position is selected. If this hap-
pens, we recommend that the climate
control air filter be replaced by a
HYUNDAI authorised repairer.
4 122
Features of your vehicle
✽ NOTICE
Checking the amount of air con-
ditioner refrigerant and compres-
•
Replace the filter according to the
Maintenance Schedule.
sor lubricant
If the car is being driven in severe
When the amount of refrigerant is low,
conditions such as dusty, rough roads,
the performance of the air conditioning is
more frequent climate control air fil-
reduced. Overfilling also has a bad influ-
ter inspections and changes are
ence on the air conditioning system.
required.
Therefore, if abnormal operation is
•
When the air flow rate suddenly
found, we recommend that the system be
decreases, we recommend that the
inspected by a HYUNDAI authorised
system be checked by a HYUNDAI
repairer.
authorised repairer.
✽ NOTICE
It is important when servicing the air
conditioning system that the correct
type and amount of oil and refrigerant is
used. Otherwise, damage to the com-
pressor and abnormal system operation
may occur.
WARNING
Improper service may cause seri-
ous injury to the person performing
the service. For more detailed infor-
mation, we recommend that you
contact a HYUNDAI authorised
repairer.
4 123
Features of your vehicle
AUTOMATIC CLIMATE CONTROL SYSTEM (IF EQUIPPED)
1. AUTO (automatic control) button
2. Driver's temperature control button
3. A/C display
4. Passenger's temperature control
button
5. Dual temperature control selection
button
6. OFF button
7. Front windscreen defroster button
8. Air conditioning button*
9. Fan speed control button
10. Air intake control button
11. Mode selection button
CAUTION
Operating the blower when the igni-
tion switch is in the ON position
could cause the battery to dis-
charge. Operate the blower when
the engine is running.
OEL049121R
4 124
Features of your vehicle
OEL049122R
OEL043125R
OLM049154
2. Set the temperature button to the
Automatic heating and air condi-
✽ NOTICE
desired temperature.
tioning
Never place anything over the sensor
1. Press the AUTO button.
located on the instrument panel to
✽ NOTICE
The modes, fan speeds, air intake and
ensure better control of the heating and
•
To turn the automatic operation off,
air-conditioning will be controlled auto-
cooling system.
select any button of the following:
matically by setting the temperature.
- Mode selection button
- Front windscreen defroster button
(Press the button one more time to
deselect the front windscreen
defroster function. The AUTO sign
will illuminate on the information
display once again.)
- Fan speed control button
The selected function will be con-
trolled manually whilst other func-
tions operate automatically.
•
For your convenience and to improve
the effectiveness of the climate control,
use the AUTO button and set the tem-
perature to 22°C/71°F.
4
125
Features of your vehicle
Manual heating and air condition-
ing
Face-Level (B, D)
The heating and cooling system can be
controlled manually by pressing buttons
Air flow is directed toward the upper body
or turning knob(s) other than the AUTO
and face. Additionally, each outlet can be
button. In this case, the system works
controlled to direct the air discharged
sequentially according to the order of
from the outlet.
buttons or knob(s) selected.
1. Start the engine.
Floor-Level (C, E, A, D)
2. Set the mode to the desired position.
For improving the effectiveness of
Most of the air flow is directed to the
heating and cooling;
OEL049123
floor.
- Heating:
Mode selection
- Cooling:
The mode selection button controls the
Defrost-Level (A, D)
3. Set the temperature control to the
direction of the air flow through the venti-
desired position.
lation system.
Most of the air flow is directed to the
4. Set the air intake control to the outside
Refer to the illustration in the “Manual cli-
windscreen.
(fresh) air position.
mate control system”.
5. Set the fan speed control to the
Also you may select 2~3 modes at the
desired speed.
If you push the button once, the corre-
same time for desired air flow.
6. If air conditioning is desired, turn the
sponding switch will turn on, and if you
- face (
) + floor (
) mode
air conditioning system on.
push the button again, the switch will turn
- face (
) + defrost (
) mode
Press the AUTO button in order to con-
off.
- floor (
) + defrost (
) mode
vert to full automatic control of the sys-
tem.
- face (
) + floor (
) + defrost (
)
mode
4 126
Features of your vehicle
OEL049124
OEL049114R
OEL049125R
Maximum (MAX) defrost mode
Instrument panel vents
Temperature control
When you select the MAX defrost mode,
The outlet vents can be opened or closed
The temperature will increase to the
the following system settings will be
separately using the thumbwheel.
maximum (HI) by holding the ▲ button.
made automatically;
Also, you can adjust the direction of air
The temperature will decrease to the
• the air conditioning system will be
delivery from these vents using the vent
minimum (Lo) by holding the ▼ button.
turned on.
control lever as shown.
When pressing the button, the tempera-
• the outside(fresh) air position will be
ture will increase or decrease by
selected.
0.5°C/1°F. When set to the lowest tem-
perature setting, the air conditioning will
• the fan speed will be set to the high
operate continuously.
speed.
To turn the MAX defrost mode off, press
the mode button or MAX defrost button
again or AUTO button.
4 127
Features of your vehicle
Adjusting the driver and passenger side
temperature equally
1. Press the DUAL button again to deac-
tivate DUAL mode. The passenger
side temperature will be set to the
same temperature as the driver side.
2. Operate the driver side temperature
control button. The driver and passen-
ger side temperature will be adjusted
equally.
Temperature conversion (if equipped)
OEL049126R
OEL049128
You can switch the temperature mode
Adjusting the driver and passenger side
between Centigrade to Fahrenheit as fol-
Air intake control
temperature individually
lows:
This is used to select the outside (fresh)
1. Press the DUAL button to operate the
Whilst pressing the OFF button, press
air position or recirculated air position.
driver and passenger side temperature
the AUTO button for 3 seconds or more.
To change the air intake control position,
individually. Also, if the passenger side
The display will change from Centigrade
push the control button.
temperature control button is operat-
to Fahrenheit, or from Fahrenheit to
ed, it will automatically change to the
Centigrade.
DUAL mode as well.
If the battery has been discharged or dis-
2. Operate the driver side temperature
connected, the temperature mode dis-
control to adjust the driver side tem-
play will reset to Centigrade.
perature. Operate the passenger side
temperature control to adjust the pas-
senger side temperature.
When the driver side temperature is set
to the highest (HI) or lowest (Lo) temper-
ature setting, the DUAL mode is deacti-
vated for maximum heating or cooling.
4 128
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст