Hyundai Tucson Fuel Cell (2016 year). Manual — part 9
Convenient features of your vehicle
Motor Overheat
Hydrogen Gas Leak
Immobilizer indicator
Warning Light
Warning Light
With smart key system
If any of the following occurs in a vehi-
This warning light illuminates:
This warning light illuminates:
cle equipped with the smart key, the
immobilizer indicator illuminates, blinks
• When the motor or inverter is over-
•
[Red] When the hydrogen leakage
or goes off.
heated.
is detected in the vehicle.
•
When the smart key is in the vehi-
Do not continue driving with an
•
[Yellow] When there is a malfunc-
cle, if the POWER button is in the
overheated motor or inverter. If
tion with the hydrogen leakage
ACC or ON position, the indicator
your vehicle remains overheated,
detection sensor.
will illuminate for approximately 30
have the vehicle inspected by an
seconds to indicate that you are
authorized HYUNDAI Tucson Fuel
If the warning light continuously
able to start the power cell module.
Cell dealer.
remains on when the vehicle is in
However, when the smart key is
"READY" state, or comes on during
not in the vehicle, if the POWER
WARNING
driving, this indicates that there may
button is pressed, the indicator will
be hydrogen leakage or a malfunc-
blink for a few seconds to indicate
Motor Overheat Warning Light
tion with the hydrogen leakage
that you are not be able to start the
detection sensor. If this occurs, stop
power cell module.
If the Motor Overheat Warning
the vehicle and have the hydrogen
•
If the indicator illuminates only for 2
Light illuminates, it indicates
system inspected by an authorized
seconds and goes out when the
overheating that may damage
HYUNDAI Tucson Fuel Cell dealer.
POWER button is turned to ON
the vehicle.
position with the smart key in the
vehicle, have the system checked
by an authorized HYUNDAI Tucson
Fuel Cell dealer.
3-62
•
When the battery is weak, if the
ESC indicator
ESC OFF indicator
POWER button is pressed, the
(Electronic Stability
indicator will blink and you are not
Control)
able to start the power cell module.
However, you can start the power
The ESC indicator will illuminate
The ESC OFF indicator will illumi-
cell module by inserting the smart
when the POWER button is in the
nate when the POWER button is in
key in the smart key holder. Also, if
ON position, but should go off after
the ON position, but should go off
the smart key system related parts
3
approximately 3 seconds. When the
after approximately
3 seconds. To
have a problem, the indicator will
ESC is on, it monitors the driving
switch to ESC function off, press the
blink.
conditions and under normal driving
ESC OFF button. The ESC OFF indi-
conditions, the ESC indicator will
cator will illuminate indicating the
remain off. When a slippery or low
ESC is deactivated.
traction condition is encountered, the
ESC will operate, and the ESC indi-
cator will blink to indicate the ESC is
operating. If the ESC system mal-
functions the indicator illuminates
and stays on. Take your vehicle to an
authorized HYUNDAI Tucson Fuel
Cell dealer and have the system
checked.
3-63
Convenient features of your vehicle
ECO Indicator Light
Low tire pressure
WARNING
ECO
indicator
Safe Stopping
This indicator light illuminates:
•
The TPMS cannot alert you to
When you activate the active ECO
The low tire pressure indicator
severe and sudden tyre dam-
system by shifting the shift lever to
comes on for 3 seconds after the
age caused by external fac-
the "E (Economic)" range.
POWER button is in the ON position.
tors.
❈ For more details, refer to
The low tire pressure indicator illumi-
•
If you notice any vehicle insta-
"Economical operation" in chapter
nates when one or more of your tires
bility, immediately take your
5.
is significantly underinflated.
foot off the accelerator pedal,
The low tire pressure indicator will
apply the brakes gradually
illuminate after it blinks for approxi-
with light force, and slowly
mately one minute when there is a
move to a safe position off the
problem with the Tire Pressure
road.
Monitoring System.
If this occurs, have the system
checked by an authorized HYUNDAI
Tucson Fuel Cell dealer as soon as
possible.
For details, refer to the TPMS on
chapter 6.
3-64
Electric power steer-
KEY OUT indicator
READY Indicator Light
KEY
ing (EPS) system
OUT
warning light
When the the POWER button is in
This indicator light illuminates:
This indicator light comes on after
the ACC or ON position, if any door
• When it is possible to drive the
the POWER button is in the ON posi-
is open, the system checks for the
vehicle.
tion and then it will go out after the
smart key. If the smart key is not in
3
power cell module is started.
the vehicle, the indicator will blink,
and if all doors are closed, the chime
When the shift lever is in D (Drive),
This light also comes on when the
will also sound for about 5 seconds.
R(Reverse) position while “READY”
EPS is not functioning properly. If it
The indicator will go off while the
indicator illuminates, if you open the
comes on while driving, have your
vehicle is moving. Keep the smart
door, the warning chime will sound.
vehicle inspected by an authorized
key in the vehicle.
Drive the vehicle with all doors
HYUNDAI Tucson Fuel Cell dealer.
closed.
WARNING
READY Indicator Light
Once the READY indicator light
comes on, all functional checks
have been completed and the
vehicle is ready to be driven.
Look around carefully before
proceeding to drive the vehicle.
3-65
Convenient features of your vehicle
REAR PARKING ASSIST SYSTEM (IF EQUIPPED)
Operation of the rear parking
WARNING
assist system
The rear parking assist system
Operating condition
is a supplementary function
• This system will activate when
only. The operation of the rear
backing up with the POWER button
parking assist system can be
ON.
affected by several factors
If the vehicle is moving at a speed
(including environmental condi-
over 6 mph (10 km/h), the system
tions). It is the responsibility of
will not be activated.
the driver to always check the
Sensors
• The sensing distance while the
area behind the vehicle before
OLMB043239
rear parking assist system is in
and while backing up.
operation is approximately 47 in.
The rear parking assist system
(120 cm).
assists the driver during backward
movement of the vehicle by chiming
• When more than two objects are
if any object is sensed within a dis-
sensed at the same time, the clos-
tance of 47 in. (120 cm) behind the
est one will be recognized first.
vehicle. This system is a supplemen-
tal system and it is not intended to
Types of warning sound
nor does it replace the need for
extreme care and attention of the
• When an object is 47 in. to 24 in.
driver. The sensing range and
(120 cm to 61 cm) from the rear
objects detectable by the back sen-
bumper: Buzzer beeps intermittent-
sors are limited. Whenever backing-
ly.
up, pay as much attention to what is
• When an object is 23 in. to 12 in. (60
behind you as you would in a vehicle
cm to 31 cm) from the rear bumper:
without a rear parking assist system.
Buzzer beeps more frequently.
• When an object is within 11 in. (30
cm) of the rear bumper:
Buzzer sounds continuously.
3-66
Non-operational conditions of
The detecting range may decrease
Rear parking assist system
rear parking assist system
when:
precautions
1. The sensor is stained with foreign
The rear parking assist system
•
The rear parking assist system
may not operate properly when:
matter such as snow or water.
may not sound sequentially
(The sensing range will return to
depending on the speed and
1. Moisture is frozen to the sensor. (It
normal when removed.)
shapes of the objects detected.
will operate normally when the
2. Outside air temperature is
moisture has been cleared.)
•
The rear parking assist system
extremely hot or cold.
3
may malfunction if the vehicle
2. The sensor is covered with foreign
bumper height or sensor installa-
matter, such as snow or water, or
The following objects may not be
tion has been modified or dam-
the sensor cover is blocked. (It will
recognized by the sensor:
aged. Any non-factory installed
operate normally when the materi-
equipment or accessories may
al is removed or the sensor is no
1. Sharp or slim objects such as
also interfere with the sensor per-
longer blocked.)
ropes, chains or small poles.
formance.
3. Driving on uneven road surfaces
2. Objects which tend to absorb the
•
The sensor may not recognize
(unpaved roads, gravel, bumps,
sensor frequency such as clothes,
objects less than 11 in. (30 cm)
gradient).
spongy material or snow.
from the sensor, or it may sense an
4. Objects generating excessive
3. Undetectable objects smaller than
incorrect distance. Use caution.
noise (vehicle horns or truck air
40 in. (1 m) in height and narrow-
•
When the sensor is frozen or
brakes) are within range of the
er than 6 in. (14 cm) in diameter.
stained with snow, dirt, or water,
sensor.
the sensor may be inoperative until
5. Heavy rain or water spray exists.
the stains are removed using a soft
6. Wireless transmitters or mobile
cloth.
phones are within range of the
•
Do not push, scratch or strike the
sensor.
sensor. Sensor damage could
7. The sensor is covered with snow.
occur.
8. Trailer towing
3-67
Convenient features of your vehicle
✽ NOTICE
Self-diagnosis
WARNING
This system can only sense objects
If you don’t hear an audible warning
within the range and location of the
sound or if the buzzer sounds inter-
Pay close attention when the
sensors; It can not detect objects in
mittently when shifting the gear to
vehicle is driven close to
other areas where sensors are not
the R (Reverse) position, this may
objects on the road, particularly
installed. Also, small or slim objects,
indicate a malfunction in the rear
pedestrians, and especially
such as poles or objects located
parking assist system. If this occurs,
children. Be aware that some
between sensors may not be detected
we recommend that you have your
objects may not be detected by
by the sensors. Always visually
vehicle checked by an authorized
the sensors, due to the object's
check behind the vehicle when back-
HYUNDAI Tucson Fuel Cell dealer as
distance, size or material, all of
ing up. Be sure to inform any driv-
soon as possible.
which can limit the effective-
ers of the vehicle that may be unfa-
ness of the sensor. Always per-
miliar with the system regarding the
form a visual inspection to
WARNING
systems capabilities and limitations.
make sure the vehicle is clear of
all obstructions before moving
Your new vehicle warranty does
the vehicle in any direction.
not cover any accidents or dam-
age to the vehicle or injuries to
its occupants due to a rear
parking assist system malfunc-
tion. Always drive safely and
cautiously.
3-68
REAR VIEW CAMERA (IF EQUIPPED)
WARNING
•
ALWAYS look around your
vehicle to make sure there are
not any objects or obstacles
before moving the vehicle in
any direction to prevent a col-
3
lision.
•
Always pay close attention
when the vehicle is driven
close to objects, particularly
OLMFC044082N
pedestrians, and especially
The Rear View Camera will activate
children.
when the power cell module is run-
•
Always keep the camera lens
ning and the shift lever is in the R
clean. The camera may not
(Reverse) position.
work normally if the lens is
Whenever the vehicle ignition is
covered with foreign matter.
cycled off and on, the rear view cam-
era will turn on when the shift lever is
put into R (Reverse).
3-69
Convenient features of your vehicle
LIGHTS
Exterior lights
Lighting control
OLMB043258
OLMB043259
Parking light position (
)
Headlight position (
)
OLMB043257
When the light switch is in the park-
When the light switch is in the head-
ing light position, the parking (posi-
light position, the headlights, parking
To operate the lights, turn the knob at
tion) lights, license plate lights, and
(position) lights, license plate lights,
the end of the control lever to one of
instrument panel lights are turned
and instrument panel lights are
the following positions:
ON.
turned ON.
(1) OFF Position
(2) Parking Light Position
(3) Headlight Position
(4) AUTO Light Position (if equipped)
3-70
High beam operation
CAUTION
•
Do not cover or spill anything
on the sensor (1) located on
the instrument panel.
•
Do not clean the sensor using
a window cleaner. The cleaner
3
may leave a light film which
could interfere with sensor
operation.
OLMB043260
•
If your vehicle has window tint
or other types of metallic
AUTO light position
OLMB043262
coating on the front wind-
When the light switch is in the AUTO
shield, the AUTO light system
To turn on the high beam headlights,
position, the parking lights and the
may not work properly.
push the lever away from you. Pull it
headlights will be turned ON or OFF
back for low beams.
automatically depending on the
The high beam indicator will light
amount of light outside the vehicle.
when the headlight high beams are
Even with the AUTO Light feature in
switched on.
operation, it is recommended to
manually turn ON the lights when
WARNING
driving at night or in a fog, or when
you enter dark areas, such as tun-
Do not use the high beams
nels and parking facilities.
when there are other vehicles
approaching you. Using high
beam could obstruct the other
driver's vision.
3-71
Convenient features of your vehicle
Battery saver function
Headlight escort function
The purpose of this feature is to pre-
If the key is removed from the
vent the battery from being dis-
POWER button or placed in the ACC
charged. The system automatically
position or the LOCK/OFF position
turns off the parking lights when the
with the headlights ON, the head-
power cell module is turned off and
lights (and/or parking lights) remain
the driver-side door is opened
(in
on for about 5 minutes. However, if
that order).
the driver’s door is opened and
With this feature, the parking lights
closed, the headlights are turned off
after 15 seconds.
will be turned off automatically if the
driver parks on the side of the road at
The headlights can be turned off by
OLMB043261
night. If necessary, to keep the lights
pressing the LOCK button on the
To flash the high beam headlights,
on when the key is removed (smart
remote key or smart key twice or
pull the lever towards you, then
key : power cell module is turned
turning the light switch to the OFF or
release the lever. The high beams
OFF), perform the following:
AUTO position. However, if you turn
will remain ON as long as you hold
the light switch to the AUTO position
1) Open the driver-side door.
the lever towards you.
when it is dark outside, the head-
2) Turn the parking lights OFF and
lights will not be turned off.
ON again using the light switch on
the steering column.
3-72
Headlight welcome function
Turn signals and lane change
CAUTION
When the headlight switch is in the
signals
ON position or in the AUTO position
If the driver gets out of the vehi-
and all doors (and tailgate) are closed
cle through other doors (except
and locked, if you press the door
the driver’s door), the battery
unlock button on the remote transmit-
saver function does not operate
ter or smart key, the headlights will
and the headlight escort function
come on for about 15 seconds.
3
does not turn off automatically.
Therefore, it causes the battery
If the headlight switch is in the AUTO
to be discharged. In this case,
position, the function can only oper-
make sure to turn off the lamp
ate at night.
before getting out of the vehicle.
To turn off the headlights immediately,
do one of the following:
• Press the door lock button.
OLMB043263
• Press the unlock button twice with-
To signal a turn, move the lever up
in 4 seconds.
for a right turn or down for a left turn
to position (A). The lever will return to
• Press the unlock button once more
the OFF position when the turn is
after 4 seconds.
completed.
To signal a lane change, move the
lever slightly and hold it in position
(B). The lever will return to the OFF
position when released.
3-73
Convenient features of your vehicle
One-touch lane change function
Front fog light (if equipped)
You can use the fog lights only when
(if equipped)
the headlights are on low beam.
When the headlight switch is in the
To activate a one-touch triple turn
AUTO position, you can also use the
signal, move the turn signal lever
fog lights when the headlights turn on
slightly and then release it. The lane
automatically. The fog lights will go
change signals will blink 3 times.
OFF when the headlights turn OFF.
CAUTION
CAUTION
If the turn signal indicator stays
When in operation, the fog lights
on and does not flash, or if it
consume large amounts of vehi-
flashes abnormally, a bulb may
cle electrical power. Only use the
be burned out or have a poor
OLMB043264
fog lights when visibility is poor.
electrical connection in the cir-
Fog lights are used to provide
cuit. The bulb may require
improved visibility when conditions
replacement.
are poor due to fog, rain, snow, etc.
Use the switch next to the headlight
switch to turn the Fog Lights ON and
OFF. The fog lights will turn on when
fog light switch (1) is turned to ON
after the head-lights are turned on.
To turn off the fog lights, turn the
switch to OFF.
3-74
Hazard warning flasher
Interior lights
Front lamps
WARNING
Do not use the interior lights
when driving in the dark. The
interior lights may obscure your
view and cause an accident.
3
CAUTION
Do not use the interior lights for
OLMF044256N
OLMF044273N
an extended period of time
The Hazard Warning Flasher should
when the power cell module is
(1) Front Map Lamp
be used whenever you find it neces-
turned off or the battery will dis-
(2) Front Door Lamp
sary to stop the car in a hazardous
charge.
location. When you must make such
an emergency stop, always pull off
Front Map Lamp:
the road as far as possible.
Press either the right or left lens to
The hazard warning lights are turned
turn the map lamp on or off. This light
on and off by pushing in the hazard
produces a spot beam for convenient
switch. This causes all turn signal
use as a map lamp at night or as a
lights to blink. The Hazard Warning
personal lamp for the driver and the
Lights will operate even though the
front passenger.
POWER button is in the LOCK/OFF
position.
3-75
Convenient features of your vehicle
Front Door Lamp:
Rear lamps
Vanity mirror lamp (if equipped)
The Front Door Lamp Switch acti-
vates the front and rear room lamps
when the switch is pressed in either of
the three positions indicated below:
DOOR:
With the switch in this position, the front
and rear room lamps come on when
the front or rear doors are opened, or
when the doors are unlocked by the
remote key or smart key.
Once all doors are closed, the room
lamps will go out gradually after about
OLMB043273
OLMB043274
30 seconds.
(1) Rear Room Lamp
Push the switch to turn the light ON
If a door is open with the POWER but-
or OFF.
ton in the ACC position or the
•
: The lamp will turn on if this
Rear ROOM Lamp Switch:
LOCK/OFF position, the lamps will
button is pressed.
remain on for about 20 minutes. If a
Press this switch to turn the room
•
: The lamp will turn off if this
lamps on and off.
door is open with the POWER button in
button is pressed.
the ON position, the lamps will stay on
continuously.
ON :
With the Front Door Room Lamp in this
position, the front and rear room lamps
remain on at all times.
OFF :
With the Front Door Room Lamp in this
position the front and rear room lamps
remain off at all times.
3-76
Glove box lamp
Luggage room lamp
3
OLMB043275
OLMF044276N
The Glove Box Lamp comes on
The Luggage Room Lamp comes on
when the glove box is opened.
when the tailgate is opened.
The parking lights or headlights must
be ON for the glove box lamp to func-
tion.
3-77
Convenient features of your vehicle
WIPERS AND WASHERS
■ Front
A : Wiper speed control
Front windshield wipers
· MIST - Single wipe
Operates as follows when the
· OFF - Off
POWER button is turned ON.
· INT - Intermittent wipe
MIST : For a single wipe, push the
lever upward and release. The
AUTO - Auto control wipe
/
wipers will operate continuous-
(if equipped)
AUTO*
ly if the lever is pushed upward
· LO- Low wiper speed
and held in this position.
· HI - High wiper speed
OFF : Wiper is not in operation
B : Intermittent control wipe time
INT : Wiper operates intermittently at
adjustment
OLMB043306
the same wiping intervals. To
■ Rear
C : Wash with brief wipes
vary the speed setting, turn the
D : Rear wiper/washer control
speed control knob.
· ON - Continuous wipe
AUTO : The rain sensor located on
the upper end of the wind-
· INT - Intermittent wipe
shield glass senses the
(if equipped)
amount of rainfall and con-
· OFF - Off
trols the wiping cycle for the
E : Wash with brief wipes (rear)
proper interval. The more it
rains, the faster the wiper
operates. When the rain
stops, the wiper stops. To vary
OLMB043307
the speed setting, turn the
speed control knob (B).
LO : The wiper runs at a lower speed.
HI : The wiper runs at a higher speed.
3-78
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст