Hyundai Tucson Fuel Cell (2016 year). Manual — part 19
Maintenance
Multi fuse
✽ NOTICE
If the multi fuse is blown, consult an
authorized HYUNDAI Tucson Fuel
Cell dealer.
OLMB073036
If the multi fuse is blown, it must be
removed as follows:
1. Turn off the POWER button.
2. Disconnect the negative battery
cable.
3. Remove the fuse panel cover by
pressing the tap and pulling up.
4. Remove the bolts shown in the
picture above.
5. Replace the fuse with a new one
of the same rating.
6. Reinstall in the reverse order of
removal.
7-56
Fuse/Relay panel description
Instrument panel fuse panel
Inside the fuse/relay box cover, you
can find the fuse/relay label describ-
ing fuse/relay name and capacity.
✽ NOTICE
Not all fuse panel descriptions in
this manual may be applicable to
your vehicle; the information is
accurate at the time of printing.
When you inspect the fuse box on
your vehicle, refer to the fuse box
label.
OLMF074261N
7
7-57
Maintenance
Instrument panel
Fuse Name
Fuse rating
Circuit Protected
AUDIO 1
10A
A/V & Navigation Head Unit
E/R Fuse & Relay Box (Interior Lamp Relay), BCM, Auto Light & Photo Sensor, Data Link
ROOM LAMP
10A
Connector, RF Receiver, Instrument Cluster,A/C Control Module, Luggage Lamp
ICM Relay Box (Rear Seat Warmer Relay), Electro Chromic Mirror, BCM, PDM, A/C
MODULE 2
10A
Compressor, VESS Unit
E/R Fuse & Relay Box (H/LAMP HI Relay, Blower Relay), COD Heater, A/C Control Module,
MODULE 4
10A
Cluster Ionizer
WIPER FRT
25A
Multifunction Switch, Front Wiper Motor, E/R Fuse & Relay Box (Wiper FRT Relay)
WIPER RR
15A
Multifunction Switch, Rear Wiper Motor, ICM Relay Box (Rear Wiper Relay)
P/WDW RH
25A
Power Window Main Switch, Rear Power Window Switch RH
P/WDW LH
25A
Power Window Main Switch, Rear Power Window Switch LH
START 1
10A
E/R Fuse & Relay Box (ATM P/N Relay)
POWER OUTLET 2
25A
Cigarette Lighter & Front Power Outlet, Rear Power Outlet
S/HEATER FRT
15A
Console Switch
PTC HEATER
15A
E/R Fuse & Relay Box (PTC Heater Relay)
MODULE 3
10A
Code Division Multiple Access, Data Logger
AMP
25A
AMP
Smart Key Control Module, Power Outside Mirror Switch, AMP, A/V & Navigation Head Unit,
AUDIO 2
10A
BCM, PDM
POWER OUTLET 1
15A
Cigarette Lighter & Front Power Outlet
IG 1
20A
E/R Fus3e & Relay Box (Fuse : AHB3, ESC3, BHDC1)
7-58
Fuse Name
Fuse rating
Circuit Protected
P/SEAT (DRV)
20A
Driver Seat Manual Switch
HTD MIRR
7.5A
Rear Defogger Switch, Driver Power Outside Mirror, Passenger Power Outside Mirror
A/BAG
10A
SRS Control Module, Tell Tail Lamp, Passenger Occupant Detection Sensor
MDPS
10A
MDPS Unit
A/CON
7.5A
A/C Control Module
SMART KEY
10A
Fob Holder, Start/Stop Button Switch, PDM, Smart Key Control Module
SAFETY POWER WINDOW
20A
Driver Safety Power Window Module
A/BAG IND
10A
Net Used
ESC Off Switch, BCM, Smart Key Control Module, CSD Switch, PDM, Tire Pressure
Monitoring Module, Multifunction Switch, Rear Parking Assist Sensor, Rear Impact Sensor,
MODULE 1
10A
Code Division Multiple Access, Gear Differential Unit, MCU, Stop Lamp Switch, Cooling Fan
Motor LH, Cooling Fan Motor RH, E/R Fuse & Relay Box (ATM P/N Relay)
Rear Combination Lamp (In) LH/RH, ATM Shift Lever ILL., BCM, A/V & Navigation Head Unit,
B/UP LAMP
10A
Electro Chromic Mirror
E/R Fuse & Relay Box (Shift Lock Relay), ATM Shift Lever, Tire Pressure Monitoring Module,
TPMS
7.5A
Rear Parking Assist Buzzer
7
A/C Control Module, Seat Belt Reminder Switch, Console Switch, Instrument Cluster,
CLUSTER
10A
A/V & Navigation Head Unit, ATM Shift Lever ILL., E/R Fuse & Relay Box (PTC Heater Relay)
H/LAMP HI
10A
E/R Fuse & Relay Box (H/LAMP HI Relay)
DR LOCK
15A
Door Lock/Unlock Relay, Tail Gate Relay, ICM Relay Box (Two Turn Unlock Relay)
S/HEATER RR
15A
ICM Relay Box (Rear Seat Warmer Relay LH/RH)
PDM 2
15A
PDM
HAZARD
15A
ICM Relay Box (Flasher Sound Relay), BCM
7-59
Maintenance
Fuel cell power module com-
partment
Inside the fuel cell power module box
cover, you can find the fuel cell
power module label describing fuel
cell power module name and capac-
ity.
✽ NOTICE
Not all fuse panel descriptions in
this manual may be applicable to
your vehicle; the information is
accurate at the time of printing.
When you inspect the fuse panel in
your vehicle, refer to the fuse panel
label.
OLMF074262N
7-60
Fuel cell power module compartment
Fuse
Fuse Name
Fuse rating
Circuit Protected
MDPS
80A
MDPS Unit
-
-
-
ESC 2
40A
ESC Module, Multipurpose Check connector
ECU
40A
EMS Box (Fuse - SENSOR M2, SENSOR M3)
MULTI
FUSE
ESC 1
40A
ESC Module, Multipurpose Check connector
BLOWER
40A
E/R Fuse & Relay Box (Blower Relay)
Smart Junction Box (Fuse - TPMS, P/SEAT(DRV), SAFETY POWER WINDOW, SMART KEY,
B+ 3
60A
Power Connector - AUDIO 1, ROOM LAMP)
B+ 2
60A
Smart Junction Box (Fuse - PTC HEATER, MODULE3, AMP, IPS0 ,1 ,2 ,3, Power Window Relay)
B+ 1
50A
Smart Junction Box (Fuse - S/HEATER RR, PDM2, DR LOCK, HAZARD, H/LAMP HI, IPS4 ,5 ,6 ,7)
RR HTD
40A
E/R Fuse & Relay Box (RR HTD Relay)
MODULE
30A
E/R Fuse & Relay Box (Fuse - BMS1, BMS2, LDC)
IG 1
40A
PDM Relay Box (IGN1 Relay, ACC Relay)
FUSE
IG 2
40A
PDM Relay Box (IGN2 Relay)
7
AHB 2
40A
AHB
HORN
15A
E/R Fuse & Relay Box (Horn Relay, B/A Horn Relay)
DEICER
15A
E/R Fuse & Relay Box (Deicer Relay)
STOP LAMP
10A
Stop Lamp Switch, Stop Signal Electronic Module
7-61
Maintenance
Fuse
Fuse Name
Fuse rating
Circuit Protected
BHDC 2
15A
High Voltage DC-DC Converter
AHB 1
25A
AHB
BHDC 1
10A
High/Low Voltage DC-DC Converter, BMS Control Module, FCU
ESC 3
7.5A
ESC Module, Multipurpose Check Connector
FUSE
AHB 3
7.5A
AHB
LDC
7.5A
E/R Fuse & Relay Box (BMS Relay), Low Voltage DC-DC Converter
BMS 1
7.5A
BMS Control Module
BMS 2
15A
BMS Blower Motor Relay
7-62
No.
Relay Name
Type
EMS BOX
E63
Wiper FRT Relay
Plug Micro (5P)
Name
Fuse rating
Circuit Protected
E64
Interior Lamp Relay
Plug Micro (5P)
SENSOR M3
30A
EMS Box (SENSOR M3 Relay)
E65
PTC Heater Relay
Plug Micro (5P)
INVERTER
15A
-
E66
ATM P/N Relay
Plug Micro (4P)
SENSOR M1
10A
-
E67
Deicer Relay
Plug Micro (4P)
SENSOR 1
10A
-
E68
Shift Lock Relay
Plug Micro (5P)
-
-
-
E69
Blower Relay
Plug Micro (4P)
SENSOR M2
15A
MCU
E70
Horn Relay
Plug Micro (4P)
SENSOR 4
15A
Stack Voltage Monitor Unit
E71
H/Lamp HI Relay
Plug Micro (4P)
Ion Conductivity Transmitter, FPD,
SENSOR 3
10A
Hydrogen Sensor
E72
BCM Relay
Plug Micro (4P)
SENSOR 2
10A
Air Intake Flow Sensor
E73
B/A Horn Relay
Plug Micro (4P)
E74
RR HTD Relay
Plug Micro (4P)
7
7-63
Maintenance
Fuel cell power module com-
partment 2
Inside the fuse/relay box cover, you
can find the fuse/relay label describ-
ing fuse/relay name and capacity.
✽ NOTICE
Not all fuse panel descriptions in
this manual may be applicable to
your vehicle; the information is
accurate at the time of printing.
When you inspect the fuse box on
your vehicle, refer to the fuse box
label.
OLMF074264N
7-64
Name
Fuse rating
Circuit Protected
Name
Fuse rating
Circuit Protected
FLM Fuse & Relay Box
HVJB
10A
HV Box (HV COD Relay, BPCU)
ACV100
10A
(ACV100 Valve Relay)
FCU
10A
FCU
FLM Fuse & Relay Box
PV400
10A
SVM
10A
Stack Voltage Monitor Unit
(PV400 Relay)
1
FLM Fuse & Relay Box
MODULE
10A
HSCU
25A
FPD600
(FPD600 1 Relay)
FLM Fuse & Relay Box
ACV190
10A
2
FLM Fuse & Relay Box
(ACV190 Valve Relay)
25A
FPD600
(FPD600 2 Relay)
ESD
10A
FLM Fuse & Relay Box (ESD Relay)
ACV100
FLM Fuse & Relay Box
30A
FLM Fuse & Relay Box (
-PTC
(ACV100 PTC Relay)
CV-TANK
15A
CV-Tank Relay)
ACV190
FLM Fuse & Relay Box
30A
FLM Fuse & Relay Box
-PTC
(ACV190 PTC Relay)
CV600
10A
(CV600 Relay)
FLM Fuse & Relay Box
PMP850
50A
FLM Fuse & Relay Box
(PMP850 Relay)
BPCU
10A
(BPCU Relay)
MAIN RELAY
10A
FLM Fuse & Relay Box (Main Relay)
7
7-65
Maintenance
High voltage box panel
Name
Fuse rating
Circuit Protected
BHDC
100A
High Voltage DC-DC Converter
PTC HTR
30A
PTC Heater
A/CON
30A
A/C Compressor
C/FAN RH
15A
Cooling Fan Motor RH
C/FAN LH
15A
Cooling Fan Motor LH
S/D COD
60A
HV COD #1 Relay
S/D COD
15A
HV COD #2 Relay
SPARE
60A
-
Fuse (S/D COD 60A/15A, BHDC
MAIN
400A
100A, PTC HTR 30A, A/CON 30A,
OLMF073263
C/FAN LH/RH
7-66
LIGHT BULBS
Consult an authorized HYUNDAI
Headlight, parking light, turn
WARNING
Tucson Fuel Cell dealer to replace
signal light, side marker and
most vehicle light bulbs. It is difficult
front fog light bulb replace-
•
Prior to replacing a light,
to replace vehicle light bulbs
ment
because other parts of the vehicle
depress the foot brake, move
the shift lever into P
(Park)
must be removed before you can get
to the bulb. This is especially true for
apply the parking brake, place
the POWER button in the
removing the headlight assembly to
get to the bulb(s).
LOCK/OFF position, and take
the key with you when leaving
Removing/installing the headlight
the vehicle to avoid sudden
assembly can result in damage to
movement of the vehicle and
the vehicle.
to prevent possible electric
shock.
✽ NOTICE
•
Be aware the bulbs may be
After heavy driving, rain or wash-
hot and may burn your fin-
ing, headlight and taillight lenses
gers.
OLMF074260N
could appear frosty. This condition
(1) Turn signal light
is caused by the temperature differ-
ence between the lamp inside and
(2) Headlight (High/Low)
the outside temperature. This is sim-
(3) Parking (Position) light
ilar to the condensation on your win-
7
(4) Parking (Position) light*
dows inside your vehicle during the
rain and doesn’t indicate a problem
(5) Side marker
with your vehicle. If the water leaks
(6) Fog light*
into the lamp bulb circuitry, have
your vehicle checked by an author-
* if equipped
ized HYUNDAI Tucson Fuel Cell
dealer.
7-67
Maintenance
Headlight
•
Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids.
•
Never touch the glass with bare
hands. Residual oil may cause the
bulb to overheat and burst when lit.
•
A bulb should be operated only
when installed in a headlamp.
•
If a bulb becomes damaged or
cracked, replace it immediately
OLMB074101
and carefully dispose of it.
1. Open the hood.
OLMB073042L
2. Remove the headlamp bulb cover
Halogen bulb
by turning it counterclockwise.
3. Disconnect the headlamp bulb
WARNING
socket-connector.
• Handle halogen bulbs with
4. Remove the socket from the
care. Halogen bulbs contain
assembly by turning the socket
pressurized gas that will pro-
counterclockwise until the tabs on
duce flying pieces of glass
the socket align with the slots on
that could cause injuries if
the assembly.
broken.
• Wear eye protection when
changing a bulb. Allow the
bulb to cool down before han-
dling it.
7-68
5. Remove the bulb by pulling it out.
Turn signal light
4. Install the socket in the assembly
by aligning the tabs on the socket
6. Insert a new bulb into the socket.
with the slots in the assembly.
7. Install the socket in the assembly
Push the socket into the assembly
by aligning the tabs on the socket
and turn the socket clockwise.
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
Parking (Position) light bulbs
8. Install the headlight bulb cover by
If the LED light does not operate,
turning it clockwise.
have the vehicle checked by an
authorized HYUNDAI Tucson Fuel
Cell dealer.
OLMB074046
1. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
2. Remove the bulb from the socket
by pressing it in and rotating it
7
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket
3. Insert a new bulb into the socket
and rotating it until it locks into
place.
7-69
Maintenance
Fog light bulbs
Side repeater light replacement
1. Remove the front bumper under
cover.
2. Reach your hand into the back of
the front bumper.
3. Disconnect the power connector
from the socket.
4. Remove the bulb-socket from the
housing by turning the socket
counter clockwise until the tabs on
the socket align with the slots on
the housing.
OLMB073045
OLMB073046
5. Install the new bulb-socket into the
housing by aligning the tabs on
■ Type A
■ Type B
the socket with the slots in the
If the LED light does not operate,
1. Remove the light assembly from
housing. Push the socket into the
have the vehicle checked by an
the vehicle by prying the lens and
housing and turn the socket clock-
authorized HYUNDAI Tucson Fuel
pulling the assembly out.
wise.
Cell dealer.
2. Reinstall a new light assembly to
6. Connect the power connector to
the body of the vehicle.
the socket.
7. Reinstall the front bumper under
cover.
7-70
Rear combination light bulb
Outside light
3. Remove the rear combination
replacement
lamp assembly from the body of
the vehicle.
OLMB073048
OLMB073047
(1) Stop/tail light
(2) Turn signal light
(3) Back-up light
(4) Side marker
7
OLMB073049
Turn signal light and stop/tail light
1. Open the tailgate.
2. Loosen the lamp assembly retain-
ing screws with a cross-tip screw-
driver.
7-71
Maintenance
7. Install the socket in the assembly
Inside light
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
Stop/tail light
8. Reinstall the lamp assembly to the
body of the vehicle.
Turn signal light
OLMB073050
4. Remove the socket from the
OLMB073051
assembly by turning the socket
Tail light and Back-up light
counterclockwise until the tabs on
the socket align with the slots on
1. Open the tailgate.
the assembly.
2. Remove the service cover using a
5. Remove the bulb from the socket
flat-blade screwdriver.
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
6. Insert a new bulb into the socket
and rotating it until it locks into
place.
7-72
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст