Hyundai Kona (2018 year). Manual — part 28

Engine compartment fuse panel

■ Gamma 1.6 T-GDI

Fuse Name

Symbol

Fuse Rating

Circuit Protected

PCB Block (A/CON Relay), E/R Junction Block (RLY.9), Purge Control Solenoid Valve,

SENSOR2

10A

RCV Control Solenoid Valve, Oil Control Valve #1~#2

ECU2

10A

ECM

ECU1

20A

ECM

INJECTOR

15A

SENSOR1

15A

Oxygen Sensor (Up), Oxygen Sensor (Down)

IGN COIL

20A

Ignition Coil #1~#4

ECU3

15A

ECM

A/CON

10A

PCB Block (A/CON Relay)

ECU5

10A

ECM

SENSOR4

15A

Vacuum Pump

ABS3

10A

ESC Control Module, Multipurpose Check Connector

TCM2

15A

TCM, Transaxle Range Switch

7-59

Maintenance

Fuse Name

Symbol

Fuse Rating

Circuit Protected

SENSOR3

10A

E/R Junction Block (RLY.7)

ECU4

15A

ECM

H/LAMP

10A

PCB Block (Head Lamp(High) Relay)

HORN

15A

PCB Block (Horn Relay)

Engine compartment fuse panel

■ Kappa 1.0 T-GDI

Fuse Name

Symbol

Fuse Rating

Circuit Protected

PCB Block (A/CON Relay), E/R Junction Block (RLY.9), RCV Control Solenoid Valve,

SENSOR2

10A

Purge Control Solenoid Valve, Oil Control Valve #1~#3

ECU2

10A

ECM

ECU1

20A

ECM

INJECTOR

15A

SENSOR1

15A

Oxygen Sensor (Up), Oxygen Sensor (Down)

7-60

Fuse Name

Symbol

Fuse Rating

Circuit Protected

IGN COIL

20A

Ignition Coil #1~#3

ECU3

15A

ECM

A/CON

10A

PCB Block (A/CON Relay)

ECU5

10A

ECM

SENSOR4

15A

ABS3

10A

Multipurpose Check Connector, ESC Control Module

TCM2

15A

SENSOR3

10A

E/R Junction Block (RLY.7)

ECU4

15A

ECM

H/LAMP

10A

PCB Block (Head Lamp (High) Relay)

HORN

15A

PCB Block (Horn Relay)

7-61

Maintenance

Engine compartment fuse panel

(Battery terminal cover)

OOS077035

Inside the fuse/relay box cover, you

can find the fuse/relay label describ-

ing fuse/relay names and ratings.

Information

Not all fuse panel descriptions in this

manual may be applicable to your

OPD076065

vehicle; the information is accurate at

the time of printing. When you inspect

NOTICE

the fuse panel in your vehicle, refer to

After checking the fuse panel in the engine compartment, securely

the fuse panel label.

install the cover. If it is not securely latched, electrical failure may occur

from water contact.

7-62

LIGHT BULBS

Consult an authorized HYUNDAI

NOTICE

Information

dealer to replace most vehicle light

bulbs. It is difficult to replace vehicle

Be sure to replace the burned-out

The headlamp aiming should be adjust-

light bulbs because other parts of the

bulb with one of the same wattage

ed after an accident or after the head-

vehicle must be removed before you

rating. Otherwise, it may cause

lamp assembly is reinstalled at an

can get to the bulb. This is especially

damage to the fuse or electrical

authorized HYUNDAI dealer.

true for removing the headlamp

wiring system.

assembly to get to the bulb(s).

Information - Traffic Change

Removing/installing the headlamp

i Information

(for Europe)

assembly can result in damage to

After heavy driving rain or washing,

The low beam light distribution is

the vehicle.

headlamp and tail lamp lenses could

asymmetric. If you go abroad to a coun-

appear frosty. This condition is caused

try with opposite traffic direction, this

WARNING

by the temperature difference between

asymmetric part will dazzle oncoming

the lamp inside and outside. This is

car driver. To prevent dazzle, ECE reg-

Prior to working on a light, firmly

similar to the condensation on your

ulation demand several technical solu-

apply the parking brake, ensure

windows inside your vehicle when

tions

(ex. automatic change system,

that the ignition switch is in the

raining and doesn’t indicate a problem

adhesive sheet, down aiming). These

LOCK/OFF position and turn off

with your vehicle. If the water leaks

headlamps are designed not to dazzle

the lights to avoid sudden move-

into the lamp bulb circuitry, we rec-

opposite drivers. So, you need not

ment of the vehicle and burning

ommend that the system be checked

change your headlamps in a country

your fingers or receiving an elec-

by an authorized HYUNDAI dealer.

with opposite traffic direction.

tric shock.

7-63

Maintenance

Headlamp, Low beam assist -

•

Always handle them carefully, and

WARNING

Static, position lamp, turn sig-

avoid scratches and abrasions. If

nal lamp and daytime running

the bulbs are lit, avoid contact with

light bulb replacement

liquids.

•

Never touch the glass with bare

Type A

hands. Residual oil may cause the

bulb to overheat and burst when lit.

•

A bulb should be operated only

when installed in a headlamp.

•

If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

OLMB073042L

•

Handle halogen bulbs with

care. Halogen bulbs contain

pressurized gas that will pro-

duce flying pieces of glass that

OOS077033

could cause injuries if broken.

(1) Headlamp (High)

•

Wear eye protection when

(2) Headlamp (Low)

changing a bulb. Allow the bulb

to cool down before handling it.

(3) Daytime running light

(if equipped) / Position lamp

(4) Turn signal lamp

(5) Front fog lamp (if equipped)

7-64

5.Insert a new bulb by inserting it into

the socket and rotating it until it

locks into place.

6.Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

7.Push the socket into the assembly

and turn the socket clockwise.

Daytime running light

OOS077034

OOS077038

If the LED lamp does not operate, we

[1] : High beam, [2] : Low beam

recommend you to have the vehicle

Turn signal lamp

checked by an authorized HYUNDAI

Headlamp and position lamp

1. Open the hood.

dealer.

1. Open the hood.

2. Disconnect the negative battery

cable.

3.Remove the socket (1) from the

3. Remove the bulb cover by turning

assembly by turning the socket

it counterclockwise.

counterclockwise until the tabs on

the socket align with the slots on

4. Disconnect the bulb socket-con-

the assembly.

nector.

(for low beam and high

beam)

4.Remove the bulb from the socket

by pressing it in and rotating it

5. Remove the bulb from the head-

counterclockwise until the tabs on

lamp assembly.

the bulb align with the slots in the

6. Install a new bulb.

socket. Pull the bulb out of the

7. Connect the bulb socket-connec-

socket.

tor. (for low beam and high beam)

8. Install the bulb cover by turning it

clockwise.

7-65

Maintenance

Type B

• Always handle them carefully, and

WARNING

avoid scratches and abrasions. If

the bulbs are lit, avoid contact with

liquids.

• Never touch the glass with bare

hands. Residual oil may cause the

bulb to overheat and burst when lit.

• A bulb should be operated only

when installed in a headlamp.

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

OLMB073042L

OOS077052

•

Handle halogen bulbs with

(1) Headlamp (Low/High)

Headlamp

care. Halogen bulbs contain

(2) Low Beam Assist - static lamp

If the LED lamp does not operate, we

pressurized gas that will pro-

(3) Daytime running light /

duce flying pieces of glass that

recommend that you have the vehi-

cle checked by an authorized

Position lamp (if equipped)

could cause injuries if broken.

HYUNDAI dealer.

(4) Turn signal lamp

•

Wear eye protection when

changing a bulb. Allow the bulb

(5) Front fog lamp (if equipped)

to cool down before handling it.

7-66

5.Insert a new bulb by inserting it into

the socket and rotating it until it

locks into place.

6.Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

7.Push the socket into the assembly

and turn the socket clockwise.

OOS077037

OOS077038

Low Beam Assist-static lamp

Turn signal lamp

1. Open the hood.

2. Disconnect the negative battery

cable.

3.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

4.Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket.

Pull the bulb out of the socket.

7-67

Maintenance

5.Insert a new bulb by inserting it into

Front fog lamp (if equipped)

Headlamp and front fog lamp

the socket and rotating it until it

aiming (for Europe)

locks into place.

Headlamp aiming

6.Install the socket in the assembly

■ Halogen type

■ LED type

by aligning the tabs on the socket

with the slots in the assembly.

7.Push the socket into the assembly

and turn the socket clockwise.

Position lamp and daytime running

light

If the LED lamp does not operate, we

OOS077059L

recommend that you have the vehicle

checked by an authorized HYUNDAI

1. Loosen the pin-type retainers of the

dealer.

under cover and then remove the

OOS077060L/OOS077061L

undercover.

1. Inflate the tires to the specified

2. Reach your hand into the back of the

pressure and remove any loads

front bumper.

from the vehicle except the driver,

3. Disconnect the power connector

spare tire, and tools.

from the socket.

2. The vehicle should be placed on a

4. Remove the bulb-socket from the

flat floor.

housing by turning the socket coun-

3. Draw vertical lines (Vertical lines

terclockwise until the tabs on the

passing through respective head

socket align with the slots of the

lamp centers) and a horizontal line

housing.

(Horizontal line passing through

5. Install a new bulb-socket into the

center of head lamps) on the

housing by aligning the tabs on the

screen.

socket with the slots in the housing.

Push the socket into the housing

and turn the socket clockwise.

7-68

4. With the headlamp and battery in

Front fog lamp aiming

normal condition, aim the head-

lamps so the brightest portion falls

on the horizontal and vertical

lines.

5. To aim the low beam left or right,

turn the driver clockwise or coun-

terclockwise. To aim the low beam

up or down, turn the driver clock-

wise or counterclockwise.

To aim the high beam up or down,

turn the driver clockwise or coun-

terclockwise.

OOS077062L

The front fog lamp can be aimed as

the same manner of the headlamps

aiming. With the front fog lamps and

battery in normal condition, aim the

front fog lamps. To aim the front fog

lamp up or down, turn the driver

clockwise or counterclockwise.

7-69

Maintenance

Aiming point

■ Halogen lamp

■ LED lamp

H1 : Height between the head lamp bulb center and ground (Low beam)

H2 : Height between the head lamp bulb center and ground (High beam)

H3 : Height between the fog lamp bulb center and ground

W1 : Distance between the two head lamp bulbs centers (Low beam)

W2 : Distance between the two head lamp bulbs centers (High beam)

W3 : Distance between the two fog lamp bulbs centers

OOS077063L/OOS077063L

Vehicle condition

Lamp type

Without driver

Halogen

625 (24.6)

617 (24.28)

1506 (59.27)

1320 (51.95)

332 (13.06)

mm (in)

LED

628 (24.71)

1503 (59.15)

880 (34.63)

With driver

Halogen

617 (24.28)

608 (23.93)

1504 (59.15)

1320 (51.95)

323 (12.71)

mm (in)

LED

620 (24.4)

1503 (59.15)

7-70

Headlamp low beam (LHD side)

■ Based on 10m screen

1 : Vertical line of the left fog lamp bulb center

2 : Horizontal line of fog lamp bulb center

3 : Cut-off line

4 : Car axis

5 : W3 (Front fog)

6 : Vertical line of the right fog lamp bulb center

7 : H3 (Front fog)

8 : GROUND

OOS077065L

1. Turn the low beam on without driver aboard.

2. The cut-off line should be projected in the cut-off line shown in the picture.

3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.

4. If headlamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.

7-71

Maintenance

Headlamp low beam (RHD side)

■ Based on 10m screen

&DU D[LV

9HUWLFDO OLQH RI OHIW

KHDGODPS EXOE FHQWHU

9HUWLFDO OLQH RI ULJKW

KHDGODPS EXOE FHQWHU

+RUL]RQWDO OLQH RI

KHDGODPS EXOE FHQWHU

&XW RII OLQH

/RZ EHDP

*5281'

OPDE076083

1. Turn the low beam on without driver aboard.

2. The cut-off line should be projected in the cut-off line shown in the picture.

3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.

4. If headlamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.

7-72

Front fog lamp

■ Based on 10m screen

1 : Vertical line of the left fog lamp bulb center

2 : Horizontal line of fog lamp bulb center

3 : Cut-off line

4 : Car axis

5 : W3 (Front fog)

6 : Vertical line of the right fog lamp bulb center

7 : H3 (Front fog)

8 : GROUND

OOS077065L

1. Turn the front fog lamp on without the driver aboard.

2. The cut-off line should be projected in the allowable range (shaded region).

7-73

Maintenance

Side repeater lamp replace-

Rear combination lamp bulb

ment

replacement

■ Type A (Standard)

OOS077067L

(1) Stop/Tail lamp

OOS077039

OOS077040

(2) Tail lamp(Type A),

■ Type B (LED)

Stop/Tail lamp (Type B)

If the light bulb does not operate, we

(3) Turn signal lamp

recommend that you have the vehicle

checked by an authorized HYUNDAI

(4) Rear fog lamp

dealer.

(LHD : Left side, RHD : Right side)

(5) Backup lamp

(LHD : Right side, RHD : Left side)

OOS077041

7-74

4. Remove the rear combination

lamp assembly from the body of

the vehicle.

5. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

6. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

OOS077066L

OOS077069L

the bulb align with the slots in the

Stop/Tail lamp

socket. Pull the bulb out of the

Tail lamp (Type A)

socket.

1. Turn off the engine.

7. Insert a new bulb by inserting it

2. Open the tailgate.

into the socket and rotating it until

3. Loosen the lamp assembly retaining

3. Remove the service cover using a

it locks into place.

screws with a cross-tip screwdriver.

flat-blade screwdriver.

8. Install the socket into the assem-

4. Remove the socket from the

bly by aligning the tabs on the

assembly by turning the socket

socket with the slots in the assem-

counterclockwise until the tabs on

bly. Push the socket into the

the socket align with the slots on

assembly and turn the socket

the assembly.

clockwise.

5. Remove the bulb from the socket

9. Reinstall the lamp assembly to the

by pressing it in and rotating it

body of the vehicle.

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

OOS077068L

7-75

Была ли эта страница вам полезна?

Да!Нет

7 посетителей считают эту страницу полезной.

Hyundai Kona (2018 year). Manual — part 28

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.