Skoda Superb (2019 year). Instruction — part 11
›
If necessary, set the required network of the data service provider.
If your data provider is not available in the list, ask your provider whether one
of the displayed providers can be used.
The parameters of the telephone service provider network can be set in the
menu item
→ → Network → Network settings.
CAUTION
If you insert a SIM card of the wrong size or in the wrong direction, there is a
risk of damage to the CarStick device.
Establishing a connection using a SIM card in the external module
Applies to Infotainment Columbus with the SIM card slot in the external mod-
ule.
A SIM card size “mini” (standard size 25x15 mm) mit enabled data services
must be used.
›
Turn on the ignition and switch on Infotainment.
›
In the Telephone main menu, switch on the → Business phone “interface”.
›
Insert a SIM card into the corresponding slot into the external module in the
storage compartment on the passenger's side
Insert the SIM card with the bevelled corner on the left and the contacts
facing downwards until it “locks”.
›
Select the SIM card usage type:
Calls too - enabling data and telephone services.
Only data connections - enabling of data services only.
›
If the SIM card is protected by a PIN code, then the PIN code of the SIM card
must be entered.
›
Confirm the entered PIN code by tapping confirm.
›
or: Tap the functional surface to save and confirm the PIN code.
›
Set the data service provider’s required network and confirm the Internet
connection.
If your data provider is not available in the list, ask your provider whether one
of the displayed providers can be used.
The parameters of the telephone service provider network can be set in the
menu item
→ → Network → Network settings.
The data connection setting using the SIM card can be configured in the
→
→ Network → Data connection:.
CAUTION
When inserting an incorrectly sized SIM card or in the wrong direction, there is
a risk of damage to the external module.
Establishing a connection using the Bluetooth
®
rSAP profile
Applies to Infotainment Columbus with the SIM card slot in the external mod-
ule.
The prerequisite for establishing an Internet connection is using a telephone
with a SIM card with active data services.
›
Turn on the ignition and switch on Infotainment.
›
Switch on the “Business” function in Infotainment, the sensor field
and
then the function surface → → Phone interface “Business”.
›
Switch on Bluetooth
®
, the sensor field
and then the function surface →
Bluetooth → Bluetooth.
›
Turn on Infotainment visibility (tap the
sensor field and then tap the
function surface → Bluetooth → Visibility: → Visible.
›
Switch on Bluetooth
®
and its visibility in the phone.
›
Connect and pair the phone with Infotainment
.
Connecting via WLAN
Introduction to the subject
Applies to Infotainment Columbus, Amundsen.
WLAN can be used to connect to the Internet, to playback audio files in the
menu media or for operating the Infotainment system using an application in
the external device (e.g. “ŠKODA Media Command”).
It is possible to connect up to 8 external devices to the Infotainment hotspot
and at the same time to connect Infotainment to another hotspot.
Switching the Infotainment hotspot on/off
›
Switch-on the ignition.
›
Switch the hotspot on/off in menu item
→ → WLAN → Mobile hotspot →
Mobile hotspot.
173
Data connection
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Setting the Infotainment hotspot
The Infotainment hotspot is factory set.
The setting can be changed in menu item
→ → WLAN → Mobile hotspot →
Hotspot (WLAN) settings.
■
Security level: - Type of access protection (always set to WPA2)
■
Network key - Access password
■
SSID: ... - Hotspot name
■
Do not send network name (SSID) - Switch the visibility of the hotspot on/off
▶
To save the configured parameters, tap the Store function surface.
Connecting an external device to the Infotainment hotspot
›
Switch-on the ignition.
›
Switch on WLAN in the external device and search for the infotainment hot-
spot.
›
Select the Infotainment hotspot and enter the required password.
›
Confirm the connection.
Note
The name of the Infotainment hotspot (SSID) and the access password can be
found in menu item
→ → WLAN → Mobile hotspot → Hotspot (WLAN) settings.
Connect Infotainment to the hotspot of the external device
Fig. 216
Main menu of the Infotainment
WLAN
The Infotainment system can only be connected to a hotspot with WPA2
access protection.
›
Switch-on the ignition.
›
If the Infotainment WLAN is not activated, activate it in the menu item
→
→ WLAN → WLAN → WLAN.
In area
A
, a list of available or previously connected hotspots is dis-
played.
The hotspot list can be updated by tapping the function surface
B
.
›
Select the hotspot and enter the password.
If the hotspot is not visible, you can establish the connection to it instructionly.
›
Tap the function surface Instruction settings.
›
Set the required hotspot parameters.
›
Tap the function surface Connect.
Icons and function surfaces in the list of available hotspots
A
Connected hotspot
Signal strength of the connected hotspot
Delete the hotspot
Hotspot connection recommendations
▶
Only leave the hotspot to be connected switched on, switch off the other
hotspot.
▶
On some hotspots, the connection setup takes longer, wait for the end of
the connection setup.
▶
If the connection is interrupted, search for available hotspots again and re-
peat connection setup.
▶
Delete unused hotspots. This shortens the time required for connection set-
up.
Note
■
It is not possible to connect Infotainment Columbus to the hotspot of the ex-
ternal device as long as a SIM card with enabled data services is in the external
module of Infotainment or a phone connected to Infotainment via the Blue-
tooth
®
rSAP profile.
■
An Infotainment Amundsen connection with external device hotspot is not
possible, as long as there is an active connection using the Carstickdevice.
Connect via WPS
Applies to Infotainment Amundsen.
It is not necessary to enter the access password when connecting via WPS.
174
Infotainment
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Connecting the Infotainment system to the hotspot of the external device
›
Switch-on the ignition.
›
In the external device, switch on the hotspot, its visibility, and the WPS con-
nection option.
›
In the Infotainment system, switch on WLAN in menu item
→ → WLAN
→ WLAN → WLAN.
›
The function surface WPS fast connection (WPS button).
Connecting the external device to the Infotainment hotspot
›
Switch-on the ignition.
›
Switch on the Infotainment hotspot in menu item
→ → WLAN → Mobile
hotspot → Mobile hotspot.
›
The function surface WPS fast connection (WPS button).
›
In the external device, switch on the WPS connection option.
SmartLink
Introductory information
Introduction to the subject
Fig. 217
Information on SmartLink on the
ŠKODA websites
SmartLink offers the ability to display certified applications on an external de-
vice equipped with a USB device on the Infotainment screen and to operate
them.
SmartLink supports the following communication systems.
▶
“Android Auto”
▶
“Apple CarPlay”
▶
“MirrorLink
®
”
Using the applications in the connected external device it is possible to use the
navigation to make a call, to listen to music.
For reasons of safety, the operation of some applications while driving is not
possible or only limited.
Read in the QR code
orenter the following address in the web brows-
er to open the website with information on the SmartLink communication sys-
tem.
http://go.skoda.eu/connectivity-smartlink
Depending on the model of the connected external device, some applications
can be operated via the Infotainment system, using your voice or using the
buttons on the multi-function steering wheel.
To activate voice control for the connected external device, hold down
or
or hold down the button on the multifunction steering wheel.
175
SmartLink
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CAUTION
To establish the connection, it is necessary for the date and time in Infotain-
ment to be set correctly. If the date and time setting is based on the GPS sig-
nal, then problems may arise with establishing a connection with a poor GPS
signal reception.
Note
■
We recommend that you use extension cords from ŠKODA Original Acces-
sories.
■
With some connected external devices, it is necessary for the connected ex-
ternal device to be “unlocked” for trouble-free functioning of the SmartLink
function.
Main menu
Fig. 218 Supported communication systems / Example of available
communication systems of the connected external device
›
to display the SmartLink main menu, tap on the sensor field
or press the
button.
›
or: Tap the
sensor field and then the function surface .
If no external device is connected, then a menu with supported communica-
tion systems SmartLink is displayed
A
Main menu
Supported communication systems
Available communication systems of the connected external device
Display of information about SmartLink
Disconnection of the active connection
Settings of the SmartLink
A
B
Android Auto
Connection set-up / disconnection
Prerequisites for establishing a connection
The external device to be connected must support the “Android Auto”
communication system.
In the external device to be connected, the “Android Auto” application
must be installed.
Some applications require the data connection in the connected external
device to be switched on.
A list external of devices, supported regions and applications that the “Android
Auto” connection supports can be found on the websites of Google Inc..
Connection set-up
›
Switch on the ignition.
›
Switch on the Infotainment system.
›
Switch on the external device.
›
Connect the external device to the USB input using a cable
.
›
Select the connection using “Android Auto”
B
Disconnection of the active connection
›
In the “Android Auto” main menu, tap the function surface .
›
Tap the “ŠKODA” function surface to go back to the main menu SmartLink.
›
Tap the function surface .
›
or: Disconnect the cable from the USB input. When reconnected, the exter-
nal device is automatically connected.
Function restriction of Infotainment
For the duration of the connection, the external device cannot be used as an
audio source in the Media menu.
By connecting the external device with “Android Auto”, all currently connected
Bluetooth
®
devices will be disconnected and the external device will automati-
cally be connected as the main telephone.
For the duration of the connection, no Bluetooth devices can be connected to
the infotainment system. The SIM card inserted in the external module can on-
ly be used for data connection.
176
Infotainment
-------------------------------------------------------------------------------------------------------------------------------------------------------------
If route guidance is taking place at this moment in Infotainment, then there
is the option to start the route guidance in the “Android Auto” application. And
vice versa, if route guidance is currently taking place in the “Android Auto”
application, then there is the possibility that this will be terminated by the
start of route guidance by the Infotainment system.
main menu
Fig. 219
Android Auto: Main menu
Main menu
Navigation applications
Telephone applications
Overview regarding current applications, telephone calls, accepted text
messages, tasks in the working directory, weather or similar.
Music applications
Display of other available applications as well as the option of returning to
the SmartLink main menu
Switching on voice control (Google Voice)
The symbol appears next to the function surface in the area
A
, Then, by
tapping on this function surface again, a list of new applications is displayed.
Apple CarPlay
Connection set-up / disconnection
Prerequisites for establishing a connection
The external device to be connected must support the “Apple CarPlay”
communication system.
The data connection of the external device to be connected must be ac-
tive.
The voice control (Siri) of the external device to be connected must be ac-
tive.
A list external of devices, supported regions and applications that the “Apple
CarPlay” connection supports can be found on the websites of Apple Inc..
Connection set-up
›
Switch on the ignition.
›
Switch on the Infotainment system.
›
Switch on the external device.
›
Connect the external device to the USB input using a cable
›
Select the connection using “Apple CarPlay”
B
Disconnection of the active connection
›
In the main menu “Apple CarPlay”, tap the function surface of the “ŠKODA”
application, the main menu SmartLink is displayed.
›
Tap the function surface .
›
or: Disconnect the cable from the USB input. When reconnected, the exter-
nal device is automatically connected.
Function restriction of Infotainment
For the duration of the connection, the external device cannot be used as an
audio source in the Media menu.
By connecting the external device with “Apple CarPlay”, all currently connec-
ted Bluetooth
®
devices will be disconnected.
For the duration of the connection, no Bluetooth devices can be connected to
the infotainment system. The SIM card inserted in the external module can on-
ly be used for data services.
177
SmartLink
-------------------------------------------------------------------------------------------------------------------------------------------------------------
If route guidance is taking place at this moment using Infotainment, then this
is terminated by starting the route guidance in the “Apple CarPlay” application.
And vice versa, if route guidance is currently taking place in the “Apple
CarPlay” application, then this will be terminated by the start of route guid-
ance by the Infotainment system.
Note
Some phone features of the connected external device can be operated in the
display of the instrument cluster
.
main menu
Fig. 220
Apple CarPlay: Main menu
Main menu
List of available applications
More pages with applications
Depending on how long the function surface is pressed:
▶
Tap - Return to “Apple Carplay” main menu
▶
Hold - Switch on voice control (Siri)
MirrorLink
®
Connection set-up / disconnection
Prerequisites for establishing a connection
The external device to be connected must support the communication
system “MirrorLink
®
”.
The external device to be connected must have at least one
“MirrorLink
®
”application installed.
Some applications require the data connection in the connected external
device to be switched on.
A
B
Connection set-up
›
Switch on the ignition.
›
Switch on the Infotainment system.
›
Switch on the external device.
›
Connect the external device to the USB input using a cable
.
›
Select the connection using “MirrorLink
®
”
B
Disconnection of the active connection
›
In the main menu of “MirrorLink
®
”, tap the function surface The SmartLink
main menu is displayed.
›
Tap the functional surface .
›
or: Disconnect the cable from the USB input. When reconnected, the exter-
nal device is automatically connected.
Function restriction of Infotainment
applies to Infotainment Columbus, Amundsen, Bolero: If you wish to use the
device to be connected in the Telephone menu, the external device must be
paired with and connected to the Infotainment system before establishing the
connection
Applies to Infotainment Swing. By connecting the external device to all cur-
rently connected Bluetooth
®
devices will be disconnected and the external de-
vice will automatically be connected as the main telephone. Depending on the
device to be connected, a connection confirmation may be required.
For the duration of the connection, the external device cannot be used as an
audio source in the Media menu.
main menu
Fig. 221
MirrorLink®: Main menu
178
Infotainment
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Main menu
Return to SmartLink main menu
List of running applications
Display of the last running application in the connected external device
Settings of the SmartLink
List of applications
More pages with applications
Applications cannot be operated while driving
Display of the function surfaces during the running application
Return to “MirrorLink
®
” main menu
Show function surfaces at the top/bottom (applies to Infotainment
Amundsen, Bolero)
Move the functional surfaces in the desired corner of the screen
(applies to the infotainment Swing)
To show/hide the function surfaces, press the controller (applies to Infotain-
ment Amundsen, Bolero).
function problems
If problems occur with the “MirrorLink
®
”connection, then one of the following
messages may occur on the screen.
■
Fault: Transfer - Disconnect and reconnect the external device
■
MirrorLink® audio is unavailable. - Disconnect and reconnect the external device
■
MirrorLink® availability on this mobile device is restricted. - it is not possible to use the
connected device during the journey or the device only has limited availabili-
ty (applies to Infotainment swing)
■
The mobile device is locked. Please unlock the mobile device to use MirrorLink® - “unlock”
the connected external device
■
Unable to start app or app not working. - Disconnect and reconnect the external
device
A
B
Application“ŠKODA OneApp”
Introductory information
Fig. 222
Information on the ŠKODA
OneApp application on the ŠKO-
DA websites
A mobile telephone connected to the Infotainment system allows you to edit
and evaluate journey data in the “ŠKODA One App” application.
After entering the following address into the web browser, the website is
opened with information on the ŠKODA mobile applications.
http://go.skoda.eu/service-app
The “ŠKODA OneApp” application is available in the App Store and Google
Play online shops.
“ŠKODA OneApp” application
›
Scan the QR code
For the full functionality of the “ŠKODA One App” application, data transfer
from external devices must be activated.
Applies to Infotainment Columbus, Amundsen, Bolero
▶
To activate data transfer from external devices, tap the
sensor field
and then tap on function surface → → Mobile device data transfer → Activate data
transfer for ŠKODA Apps.
Applies to Infotainment Swing
▶
To activate data from external devices, press the
button, then tap on
function surface → Activate data transfer for ŠKODA apps.
Note
Some functions of the application are not available in all countries or there is a
function restriction during the journey
179
SmartLink
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Connecting to Infotainment
The mobile telephone can be connected to the Infotainment system using the
SmartLink function or via WLAN.
Connection by SmartLink
›
Switch on the ignition.
›
Establish the connection via SmartLink (eg “MirrorLink
®
”)
.
›
In the list of available applications, select the “ŠKODA One App” application.
Depending on the model of the connected external device, some applications
can be started using voice activation, via the Infotainment screen, using the
operating elements on Infotainment, or using the buttons on the multi-func-
tion steering wheel.
Once connected, the contents of the application in the infotainment screen
may be displayed.
A possible connection between the mobile telephone and the Infotainment
system via WLAN will be terminated after a connection is established using
SmartLink.
Connection via WLAN (applies to Infotainment Columbus, Amundsen)
›
Switch on the ignition.
›
Establish the WLAN connection
.
›
In the mobile telephone, start the “ŠKODA OneApp” application.
Disconnection
The connection can be switched off in one of the following ways.
›
Switch off the ignition for longer than 5 seconds (for vehicles with a starter
button, switch off the engine and open the driver's door).
›
End the connection in the “ŠKODA OneApp” application.
›
Disconnect the mobile telephone from the USB port or terminate the WLAN
connection.
Navigation
Introductory information
Navigation - function sequence
Applies to Infotainment Columbus, Amundsen.
Route guidance is started as follows.
›
Search for/ enter a new destination or Select one of the stored destinations.
›
Confirm the route calculation in the destination details or if necessary, adjust
the route options.
›
Select the preferred route type, if this is requested by Infotainment.
A route calculation occurs and route guidance starts.
The route guidance is provided by graphical nav. announcements.
There is an option to add additional destinations during route guidance, or to
adapt the route.
If a traffic radio station is available, information concerning traffic delays is
evaluated by Infotainment and, if necessary, an alternative route is offered.
If you deviate from the route, then a new route calculation is carried out.
GPS satellite signal
Infotainment uses the GPS (Global Positioning System) satellite signal for
route guidance.
Outside the range of the GPS satellite signal (e.g. in dense vegetation, in tun-
nels, parking garages, etc.), Infotainment navigates only with restrictions using
vehicle sensors.
The unit offers the possibility to show in the split screen display the following
Position
on page 183 information about the current geographical po-
sition of the vehicle and the satellite signal.
Geographical latitude
Geographical longitude
Elevation
Number of received/available satellites
If no GPS satellite signal is available, no values are displayed.
180
Infotainment
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Navigation data
Columbus navigation data source
The navigation data is stored in the internal Infotainment memory.
Amundsen navigation data source
The navigation data is stored on an Original SD card.
In order to ensure the function of the navigation, the Original SD card, with the
navigation data, must be inserted in the respective slot in the external module
.
If the original SD card should be damaged or lost, a new original SD card can
be purchased from the ŠKODA Original Accessories.
With a non-original SD Card, the navigation does not work.
Finding out the version of the navigation data
›
In the Navigation main menu, tap on the functional surface → Version infor-
mation .
Update navigation data
We recommend that you update the navigation data on a regular basis.
The Infotainment can give incorrect driving recommendations if the road con-
dition or the traffic situation does not match the navigation data. This can lead
to route guidance being carried out using a different route or proposing a
change of direction in a one-way street. Therefore, observe the respective
traffic signs while driving, which always have priority over the driving recom-
mendations.
The information on updating the navigation data is to be obtained from a
ŠKODA partner or on the following ŠKODA Internet pages.
http://go.skoda.eu/updateportal
When activated online services “Infotainment online”
can the naviga-
tion data for the Infotainment Columbus Updating online
tion data and POI categories Import / Update online,
Navigation data and POI categories Import / Update online
Manual update
When “Infotainment Online”
online services are activated, there is
the option of downloading/updating navigation data (applies to Infotainment
Columbus) or of downloading POI categories created in the user profile on the
“ŠKODA Connect Portal” website.
▶
In the Navigation main menu, tap the functional surface → Version information
→ Update (online) → Retrieve.
▶
or: Tap the
sensor field and then the function surface → .
A menu for importing/updating the navigation data and POI categories is dis-
played.
▶
Tap the functional surface and select one of the following menu items.
■
All - Import all the available navigation data
■
Favourites - Import of navigation data preferably countries / regions (applies to
the infotainment Columbus)
■
POIs - Import of the POI category created in the user profile on the “ŠKODA
Connect Portal” website
■
Maps - Import of the navigation data available for the respective countries/re-
gions (applies to Infotainment Columbus)
▶
Select the desired list entries.
▶
Tap on function surface Retrieve and confirm the deletion.
Automatic update
Applies to vehicles with the Infotainment Columbus: if the online services
“Infotainment Online”
are activated and an update of the navigation
data for the current vehicle position or the route destination is available, the
infotainment will issue this automatic note and offer an update option.
During the upgrade process, infotainment is usable without limitation.
To complete the update of the navigation data, the ignition and Infotainment
must be switched off for at least 30 min.
181
Navigation
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Main menu
Fig. 223 Navigation: Main menu
›
To display, tap the sensor field
.
›
or: Tap the
sensor field and then the function surface .
Description of the function interfaces
A
Context-dependent:
Route guidance is disabled - Search / enter a new destination
Route guidance is enabled - The following menu is displayed:
▶
Route details - Displays the route details
▶
Change route in map - Displays a menu for the route change in the map
(valid for Infotainment Columbus)
▶
Congestion ahead - Manual adjusts traffic conditions
▶
Enter destination - Search / enter a new destination / stopover
▶
Stop route guidance - Stops route guidance
The following menu is displayed:
▶
Curr. current position - Store the current vehicle position as the flagged
destination
▶
Routes - Displays the list of saved routes
▶
Destinations - Display the list of stored destinations
▶
Last destinations - Display the list of recent destinations to which route
guidance was carried out
▶
Home address - Route guidance to your home address
Search for POIs in categories
,
and
Map display options
Playback control Media/Radio (does not apply to vehicles with Infotain-
ment Amundsen and the digital instrument cluster)
Display for the volume setting of the navigation announcements/repeti-
tion of the navigation announcement
Navigation settings
Change the map display between the digital instrument cluster and the In-
fotainment screen (applies to vehicles with Infotainment Amundsen and
the digital instrument cluster)
Map
Fig. 224
Card description
The following information and function surfaces can be displayed in the
map.
Vehicle position
Route
Function interfaces for card use
Functional surface of the POI
Functional surface for the POI list
Function surface for displaying a traffic incident
Information on the maximum permitted speed
Destination position
Intermediate destination position
Destination position Home address
Favourite position
Information in the status line
Street name / street number of the current vehicle position
Distance to destination
Route to the stopover
Estimated travelling time to the destination
B
A
B
C
D
E
F
G
182
Infotainment
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Estimated travel time to the stopover
Estimated time of arrival at destination / stopover
additional window
Fig. 225
Split screen
Applies to vehicles with Infotainment Amundsen and the digital instrument
cluster: when the map display is displayed in the digital instrument cluster, the
split screen is always shown and cannot be dimmed.
›
To switch on/offin the main menu Navigation, tap on the function surface
→ Split screen.
›
To select content of the additional window
A
tap the function
surface Tap and select one of the following menus, depending on the con-
text.
■
Audio - Operation of Radio/Mediaplayback
■
Compass - Displays the current vehicle location in relation to the compass di-
rections
■
Freq. Routes - Displays the three most frequently travelled routes (if route
guidance is disabled)
■
Manoeuvre - Display graphical driving recommendations (if route guidance is
enabled)
■
Position - Displays the geographical coordinates of the current vehicle loca-
tion
■
Map - Preview card display (applies to vehicles with Infotainment Columbus,
without the digital instrument cluster)
Search for destination and enter
Selecting the type of destination search/destination entry
Fig. 226
Selecting the type of destina-
tion search/destination entry
›
Route guidance is disabled - From the navigation main menu, the function
surface → .
›
Route guidance is enabled - From the main menu navigation, tap on the
function surface → Enter destination → .
Function surfaces
Search for a destination or POI (point of interest) by name
Destination entry by address
Online POI search
Search for a point along the route (only works with active route guidance)
Destination input via the map point or using the GPS coordinates
Search POI destination /
Fig. 227
Menu for the destination search
A
B
C
D
E
183
Navigation
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Fig. 228 List of destinations visited: in the navigation data / online
The feature allows a full text search of locations or points of interest (POI) by
entering keywords.
Show menu
›
Route guidance is disabled - From the navigation main menu, the function
surface → .
›
Route guidance is enabled - From the main menu navigation, tap on the
function surface → Tap Enter destination
›
Then tap the function surface of one of the menu items for the destination
search
A
,
C
or
D
Function surfaces
and
Input line
Depending on the search mode, the following symbols are displayed
- Display the map as well as the list of the destinations listed in the navi-
gation database
- Display the map as well as the list of online destinations
- Select the destination search/destination entry
List of last destinations (if no character is entered) / List of visited destina-
tions
Keypad
Status of online services
Find destination
▶
Enter the POI name or the POI category (POI) and, if required, the place and
street name or house number/postal code.
A list of the destinations found is displayed in area
D
.
A
B
C
D
E
F
▶
Select the desired destination and the destination details will be displayed.
▶
or: Tap the
B
function surface.
A map with the following symbols and a list of the destinations found is dis-
played.
Destinations found in the navigation data
- .
Destinations found online
- .
▶
Select the desired destination and the destination details will be displayed.
Enter destination using the address
Fig. 229 Enter destination using the address: Main menu / List of visited
destinations
Show menu
›
Route guidance is disabled - From the navigation main menu, the function
surface .
›
Route guidance is enabled - From the main menu navigation, tap on the
function surface → Tap Enter destination
›
Then tap the function surface →
B
Enter destination
›
Enter the destination address and then confirm
- .
›
Tap the function surface to see the destination details.
Relevant names (e.g. Place/street names) are offered in the entry line during
entry, depending on the context. The location of the proposed destination can
be displayed by tapping the function surface Map.
Depending on the number of places visited, a map with a list of visited places
can be displayed automatically
- .
184
Infotainment
-------------------------------------------------------------------------------------------------------------------------------------------------------------
The map with the list of visited locations can be accessed manually by tapping
the function surface .
Entering a destination via the map point and using GPS coordinates
Fig. 230 Enter destination: via the map point / using the GPS coordi-
nates
Show menu
›
Route guidance is disabled - From the navigation main menu, the function
surface .
›
Route guidance is enabled - From the main menu navigation, tap on the
function surface → Tap Enter destination
›
Then tap the function surface →
E
Enter destination via map point
›
By sliding the screen move the desired destination into the cross-hair
- .
›
Tap the function surface to see the destination details.
Enter destination through GPS coordinates
›
Tap in the values of the GPS coordinates one at a time and adjust
» Fig. 230
,
›
Tap the function surface to see the destination details.
If information is available about the point entered in the navigation data, then
these will be displayed instead of the GPS coordinates (e.g. address
A
).
Entering a destination via the map point
Fig. 231
Menu after tapping the map
point
Tap on the map to display the symbol and a menu with the following menu
items (depending on the context)
.
Display the destination details
Display the POI details/display the POI list (function surface) )
Start route guidance to the selected point
Paste the selected point as the next destination in the current route
guidance
Start route guidance to the favourite
Start route guidance to the home address
Destination search in the vicinity of the selected point
Define the starting point for demo mode (if it is turned on)
Find petrol station, restaurant or car park
Fig. 232 List of petrol stations visited: in the navigation data / online
A
B
C
185
Navigation
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Fig. 233 List of car parks visited: in the navigation data / online
The Infotainment allows you to find petrol stations, restaurants or car parks
quickly in the navigation data as well as online.
›
In the Navigation main menu, tap the functional surface .
›
The function surface of the desired category button.
›
or: Tap the
sensor field and then the function surface → or .
Search destination in the navigation data
Depending on the context below a list be examined POIs in the selected cate-
gory is displayed.
▶
There is no route guidance - The nearest destinations in a radius of 200 km
from the current vehicle position are displayed.
▶
There is a route guidance - Destinations on the route or near the route are
displayed.
Find Target online
When “Infotainment Online”
services are activated, a list of POIs
from the selected category in a radius around the current vehicle position is
displayed, regardless of whether or not route guidance is taking place.
After performing destination search, it is possible to switch between the list of
visited in the navigation data or online goals by one of the following functional
areas on the position
A
Displays the list of destinations visited in the navigation data.
Displays list of last destinations
Note
With function activated → Fuel options → Select preferred fuel station function ac-
tivated, the preferred fuel stations are displayed in the first three positions
during the fuel station search.
Saved destinations
Last destinations
List of last destinations
›
In the Navigation main menu, tap on the function surface → Last destinations.
Details of the last destination (not applicable to Infotainment Columbus)
›
In the main Navigation menu, tap the
sensor field.
If route guide is disabled, then the details of the last destination are displayed
to where the route guidance was carried out. If route guidance is enabled,
Then the details of the final destinations are displayed.
Last destinations menu for destination / POI search
In the menu for finding destinations in
D
, a short list of the most
recent destinations is displayed.
Function surfaces in the list of last destinations
- Destination search by name (the function surface is displayed with
more than 5 entries available)
- Display the details of the selected destination
target memory
Fig. 234 Select list of stored destinations / categories of saved destina-
tions
Search
186
Infotainment
-------------------------------------------------------------------------------------------------------------------------------------------------------------
List of stored destinations
›
In the Navigation main menu, tap on the function surface → Destinations.
›
Tap on function surface
A
and select one of the following catego-
ries of saved destinations
B
All saved destinations
▶
- Flagged destination (vehicle position at the time of storage)
▶
- Stored destination (manually saved destination/destination impor-
ted in vCard format)
▶
- Favourite (destination with additional favourite property)
Favourites (the favourite location is shown in the map by the symbol
).
Telephone contact addresses of the connected telephone or the inserted
SIM card.
Online destinations created in the user profile on the “ŠKODA Connect
Portal” website or in the “ŠKODA Connect” application
Function surfaces in the list of stored destinations
- Destination search by name (the function surface is displayed if there
are several entries on the next page of the list)
- Display the destination details
Store target
▶
In the Navigation main menu, tap on the function surface → Last destinations.
▶
Tap the functional surface Tap on the desired destination, the destination
details are displayed.
▶
Tap on the function surface Store .
▶
Rename the destination if necessary and confirm storage.
“Flagged destination” Save (current vehicle position)
▶
In the Navigation main menu, tap on the function surface → Store → Store
current position.
▶
By then pressing the function surface Rename the flagged destination can be
renamed and stored as a destination in the dest. memory.
By storing the next flagged destination, the last flagged destination will be
overwritten. To maintain the existing flag destination, this destination must be
stored in the Infotainment memory.
Save as a favourite / cancel
It is not possible to store a contact, a vCard or target image as a favourite.
▶
In the Navigation main menu, tap on the function surface → Destinations.
▶
Tap the functional surface and select the desired list of destinations.
Search
▶
Show the destination details by tapping on the function surface at the de-
sired destination.
▶
Tap on the function surface Edit .
▶
Tap on the function surface Favourite .
Delete destination
▶
In the Navigation main menu, tap on the function surface → Destinations.
▶
Tap the functional surface and select the desired list of destinations.
▶
Show the destination details by tapping on the function surface at the de-
sired destination.
▶
Tap the function surface Edit.
▶
Tap the function surfaceDelete and confirm the deletion.
Home address
Define home address
When your home address is not entered, then proceed as follows.
›
In the Navigation main menu, tap on the function surface → Home address.
›
Defining the home address using the current vehicle position or by entering
the address.
Change the home address
›
In the Navigation main menu, tap on the function surface → Manage memory
→ Define home address.
›
Tap the function surface Edit .
›
Edit the home address or set one up using the current vehicle position or by
entering the address.
Delete home address
›
In the Navigation main menu, tap on the function surface → Manage memory
→ Delete user data → Home address.
›
Tap the function surfaceDelete and confirm the deletion.
187
Navigation
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Import your own goals
Introduction to the subject
Fig. 235
MyDestination application on
the ŠKODA websites
Fig. 236
Websites ŠKODA Connect
Your own destinations can be created using the ŠKODAapplication
“MyDestination”, in the user profile on the website “ŠKODA Connect Portal” or
in the application “ŠKODA Connect”
By reading the QR code
or after typing the following address in the
web browser, more information on the “MyDestination”application is dis-
played.
http://go.skoda.eu/my-destination
For the “ŠKODA Connect Portal” refer to the website of “ŠKODA Connect”.
This is carried out by reading the QR code
or after entering the fol-
lowing address into the web browser.
http://go.skoda.eu/connectivity
Goals in vCard format
In the Infotainment memory, a custom destination can be imported in the
vCard format (*.vcf) from an SD card or a USB source.
Import
›
Insert the SD card into the external module or connect a USB source with
the own destination file.
›
In the Navigation main menu, tap on the function surface → Manage memory
→ Import destinations (SD/USB).
›
Select the source and confirm the import.
Route guidance
›
In the Navigation main menu, tap on the function surface → Destinations →
→ .
›
Search for and select the desired imported destination.
Delete own destination
›
In the Navigation main menu, tap on the function surface → Destinations →
→ .
›
Tap the functional surface Tap on the desired own destination.
›
In the destination details, tap the function surface Edit → Delete and confirm
the deletion.
In the application “MyDestination” created POI categories
Import / update
›
Insert the SD card into the external module or connect a USB source with
the POI categories.
›
In the Navigation main menu, tap on the function surface → Manage memo-
ry→ Update "My POIs" (SD/USB) Tap.
If there is already the same POI category name in the Infotainment memory,
then it will be overwritten during import.
Show POIs in the map
›
In the Navigation main menu, tap on function surface → Map → Select catego-
ries for POIs → My points of interest (Personal POI).
›
Select the imported POI category.
Guidance to the POI
›
Tip on the traffic obstruction icon in the map.
There are details of the selected target appears
.
188
Infotainment
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст