Dacia Solenza (engine E7J). Service manual — part 142
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 25
Diagnostic
8. 14G STATE : DOORS BLOCKING/ UNLOCKING
RECOMMENDATION
The state 10G (anti starting) must be ACTIVE.
Check the continuity and the isolation related to the +12 V and to the mass of the electric
wiring on the line E.C.U. decoder
Pin B2 pole 1 door locking switch.
Pin B5 pole 5
Fix the electric wiring if necessary or replace the switch.
If the incident persists, replace the E.C.U. decoder.
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 26
Diagnostic
FAILURES LOCATING BASED ON CLIENT CLAIM
(algorithm for damage locating)
ALP1. MISSING COMMUNICATION CLIP TESTER / E.C.U DECODER
RECOMMENDATION Check if the lines K and L are not perturbed by another computer
of the vehicle.
Check the condition of the F03, F04 fuses from cockpit fuse box.
Be sure the CLIP tester is not the cause of the failure, by trying the communication with
another computer of the vehicle.
Check the tension of the battery (U>12,3V). If it is necessary, charge the battery.
Check the correct connection of the E.C.U. decoder to the wiring.
Check the supply of the E.C.U. decoder : - mass at pin A8;
- supply (+IC) at pin A9.
Be sure that the diagnostic socket is correctly supplied.
Check the continuity and the isolation of the electric wiring on the pins’ line corresponding to:
E.C.U. decoder A3 7 diagnostic socket
A4 15
If the dialogue CLIP tester – E.C.U. decoder cannot be established, then replace the decoder.
When the communication with the tester is established, solve the
AFTER REPAIRING
failures displayed by CLIP.
Perform a conformity checking.
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 27
Diagnostic
ALP2. CONTACT SET ON THE ANTI STARTING INDICATOR BLINKS
(THE ENGINE IS NOT STARTING)
RECOMMENDATION
-
Set the contact on.
Connect the CLIP tester.
Is there any communication with the E.C.U.
decoder ?
See ALP1
.
Check the fuse F03 for anti starting bushing
supply.
Is it good?
Replace the fuse.
Set the contact on and check if the state 4D
becomes ACTIVE ?
Is the state 19 D PASSIVE ?
Perform « Procedure for replacement
E.C.U. decoder and memorising anti
starting code » if the starter is new ;
if it’s not new, replace it.
Set the contact off. The anti starting indicator
will start to blink after 10 seconds.(ACTIVE
anti starting ).
Set again the contact and check: the failure
« Defective communication decoder bushing ».
Does exist such a failure ?
Study « DEFECTIVE
COMMUNICATION BUSHING
– DECODER » from the chapter
DIAGNOSTIC.
Study « STATE 4D : SUPPLY +12
V » from chapter DIAGNOSTIC.
Try the engine starting with the second key.
Is the engine starting ?
Replace the first key.
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 28
Diagnostic
No
Is the anti starting bushing correctly fixed on
the steering column and is it correctly connected
?
Position the bushing and fix its
connection.
Check the continuity and the isolation related
to the mass and the +12 V wiring.
Pin2
mass
Pin3
supply +IC
Pin4
pin A2 of the
E.C.U. decoder.
Is the wiring in good condition?
Fix the electric wiring.
Disconnect the E.C.U. decoder and check the
presence of +12 V at pin A2 of the wiring.
Is there any tension?
Replace the anti starting bushing.
Connect the E.C.U. decoder. Perform the
impulse detection test with the tester CLIP
branched to the pin A2 of the E.C.U. decoder.
Set the contact on and check the presence of
an impulse. Is there any impulse?
Replace the E.C.U. decoder.
Replace the key.
No
No
No
No
Yes
Yes
Yes
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст