Dacia SuperNova (engine E7J). Service manual — part 51
CV JH3 - 050
21
MANUAL GEARBOX
21 - 12
Dismount the fixed pinion of the 5 th gear
by means of the C.V. 1000 extractor and
the body extractor C.V. 22 -01.
The hub of the 5 th step synchronizer is
extracted by means of the C.V. 1170 extractor.
Dismount the synchronizer ring of the 5
step, the inner bushing of the pinion, the pinion
and its supporting washer.
The gearbox is set in the dead point, then
engage the 3-d step.
Dismount the external screws fixing the
crankcase of the mechanisms and blocking
pin of the reverse driving pinion axle.
Dismount the reverse driving contact (B).
GEARBOX DISMOUNTING
C.V. 1170
C.V. 1000
C.V. 22 -01
CV JH3 - 050
21
MANUAL GEARBOX
21 - 13
In order to recover the balls and the locking
springs of the shafts, two magnets placed in the
C orifices are used.
Pull the control shaft towards exterior.
The crankcases are separated.
Rotate to the left the shaft – reverse driving
pinion assembly and dismount the control reverse
driving shaft velocity 5-th step.
Take out the fork pin 3-4 by means of the
C.V. 949 device and dismount the axle and
3-4 fork assembly.
Simultaneously, dismount the primary shaft
and secondary shaft assembly with the axle
and 1-2 fork.
Place vertically the secondary shaft, with
the pinion of the 1 step downwards, so that
the other pinions will not fall.
Recover the locking pins (A) and (B) of
the command axles.
GEARBOX DISMOUNTING
Easy lift the primary shaft and dismount the
shaft and reverse driving pinion assembly.
C.V. 1170
C.V. 94 9
A
B
CV JH3 - 050
21
MANUAL GEARBOX
21 - 14
THE PRIMARY SHAFT
The primary shaft shall not be repaired and is not adjustable.
The shaft has a spry nozzle (B) which cannot be dismounted.
Clean the oiling – groove of the 5 th step
The oil seal ring in front of the shaft and the bearing cams are in direct contact with the shaft.
Check the state of the shaft in the operation area (A) of the oil seal; ring, and if this shows
ridges or irregularities, it will be replaced.
REPLACING THE BEARINGS OF THE PRIMARY SHAFT
The bearings of the primary shaft are freely mounted on it.
There are two types of bearings:
- a cylindrical one with balls , pressed into the crankcase of the mechanism;
- a cylindrical one with rolls , pressed into the crankcase of the clutch-differential, together
with the clutch shaft oil seal ring.
The bearings replacement is performed only with identical bearings with the original ones.
GEARBOX DISMOUNTING
CV JH3 - 050
21
MANUAL GEARBOX
21 - 15
BEARING DISMOUNTING OF THE MECHANISMS CRANKCASE
The safety ring of the bearing (the holding ring) is widened by means of a pair of safety
pincers, then the bearing is extracted from the crankcase by hammering towards the inside of the
mechanisms crankcase, by means of the C.V. 551 device.
BEARING REMOUNTING OF THE MECHANISMS CRANKCASE
Replace the safety of the bearings with a new one, then it is introduced into its groove in the
mechanisms crankcase, so that it keeps its position as compared to the crankcase (the safety
shows a shoulder).
The bearing lying at the outside of the crankcase of the mechanism is pressed towards the
inside of it, until the safety fits into the groove carved on the outer ring of the bearing.
Mounting the bearing is performed by means of the C.V. 551 device.
C.V. 551
GEARBOX DISMOUNTING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст