Dacia Pick-Up 1304/1305/1307. Service manual — part 95
37
MECHANICAL ELEMENTS CONTROLS
BRAKE PEDAL AND CLUTCH
D
ISMO UNTING
Remove the safety clip (1).
Detach the spring (2) of the clutch cable
shaft.
Remove the pins and the shaft (3) of
the main cylinder pushing rod.
Remove the clutch pedal from the
pedals shaft.
By means of a bronze nail, push the
pedals shaft towards the right, then
remove the brake pedal.
R
EMO UNTING
Grease the shaft (A) with special grease
containing MoS2.
Mount in the following order:
-
the brake pedal(F);
-
the washer (C).
Place the shaft (A) together with the
elastic pin (B) in the pedal support.
Place the shaft in the second support
bore, then place the following items:
-
the washer (D);
-
the clutch pedal (E).
Check that the elastic pin (B) is well
set in its seat.
Mount the safety lock (1).
Attach the following parts:
-
the clutch cable;
-
the pushing rod of the main cylinder, on the brake pedal.
Adjust:
-
the clutch stroke;
-
the brake stroke.
37 - 15
MECHANICAL ELEMENTS CONTROLS
37
CLUTCH CABLE – CLUTCH STROKE ADJUSTMENT
CLUTCH CABLE REPLACEMENT
D
ISMO UNTING
Dismount the clutch lever cable.
Dismount the attachment clip (1) of the
pedal.
Push the shaft rightward and take out the
pedal.
Release the spring (2) and the shaft (3) of
the fork.
Dismount the fork.
Release the cable from the housing stopper
on the pedal support and dismount it.
R
EMO UNTING
Perform the dismounting operations in the reverse order.
Grease :
-
the pedal shaft;
-
the fork shaft.
Adjust the clutch stroke.
CLUTCH GEAR STROKE ADJUSTMENT
Loosen the lock nut (1).
Tighten or unscrew the nut (2) until
obtaining the 2,5-3,5 mm stroke at the lever
end.
Lock the lock nut.
37 - 16
37
MECHANICAL ELEMENTS CONTROLS
THE STEERING COLUMN SUPPORT ASSY AND FIRE WALL
D
ISMO UNTING
Dismount the throttle, brake and clutch pedals.
Dismount the attachment screws (2) of the steering column mounting (1) on the wall
metal.
R
EMO UNTING
Perform the dismounting operations in the reverse order by screws tightening at the
moment of 1,5 – 2,5 daNm.
37 - 17
2
1
MECHANICAL ELEMENTS CONTROLS
37
THROTTLE PEDAL REPLACING
D
ISMO UNTING
Release the throttle pedal by dismounting the clip (8),the washer (7) and support shaft
(6).
Dismount the attachment nuts of the pedal support (2) and release the throttle pedal (3).
R
EMO UNTING
Perform the dismounting operations in the reverse order then adjust the throttle stroke
at the “ maximum” position of the valve, which is obtained by pedal pressing till its
calibration on the limiter (4) and by threaded pin adjustment (5) in this position.
THROTTLE CONTROL CABLE REPLACEMENT
D
ISMO UNTING
Dismount the attachment screw of the cable(1) from the throttle control lever,then
remove the clips (8) the washer (7), and the pedal shaft (6),releasing the attachment throttle
pedal.
R
EMO UNTING
Perform the dismounting operations in the reverse order, followed by the corresponding
adjustment of the throttle pedal.
37 - 18
THROTTLE PEDAL
1
2
3
4
6
7
8
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст