Dacia Pick-Up 1304/1305/1307. Service manual — part 74
FRONT BEARING ELEMENTS
31 - 20
31
BRAKE CALIPER SUPPORT
D
ISMO UNTING
Lift the vehicle on a two columns
elevator;
Dismount:
- the wheel;
- the caliper without disconnecting the
flexible connection;
- the brake pads.
Dismount:
- the two screws M 6 x 1 that attach
the protector on the brake caliper support;
- the two screws M 8 x 1,25 that
attach the brake caliper support on the steer-
ing knuckle;
- the two screws M 12 x 1,25 that at-
tach the brake caliper support on the steering
knucklethe brake caliper support.
R
EMOUNTING
NOTE:
Upon remounting, grease the screws with FIXAMED R 58 and replace the Grower
washers.
Place the brake caliper support in the right position.
Tighten the screws M 12 x 1,25 at the required moment of 6,5 daNm.
Tighten the screws M 6 x 1 that attach the protector at the required moment of 1,3 daNm.
Mount:
- the brake pads;
- the brake caliper support;
- the wheel.
Take down the vehicle from the elevator.
T
IGHTENING
MOMENTS
( în daNm )
The attachment caliper support screw on steering knuckle . ...6,5
The attachment protector screw on the caliper support. . . . .1,3
The attachment protector screw on the steering knuckle. . .
. ...2
31
FRONT BEARING ELEMENTS
31 - 21
STEERING KNUCKLE
D
ISMO UNTING
SPECIAL
TO OLS
:
D
ENO MINATION
C
ODE
Transmission gear and hub extractor
PF 235 A
Transmission gear mounting device
PF 236
Ball joints extractor
PF 476
Front axle support cross bar
PF 509
Dynamometric wrench
MOT 50
T
IGHTENING
MOMENTS
- Upper ball joint nut. . . . . . . . . ...5 daN.m
- Lower ball joint nut. . . . . . . . . ...5 daN.m
- Steering ball joint nut. . . . . . . . . 4 daN.m
- Transmission nut. . . . . . . . . . ..23 daN.m
- Wheels nut. . . . . . . . . . . . . .9 daN.m
- Caliper support attachment screws
. . . . 6,5 daN.m
D
ISMO UNTING
Lift the vehicle by means of an elevator.
Mount the PF 509 support cross bar.
Dismount:
- the wheel;
- the brake caliper together with flexible
connection;
- the brake caliper support and the mud
flap;
- the transmission gear nut.
FRONT BEARING ELEMENTS
31 - 22
31
STEERING KNUCKLE
Mount the PF 235 A extractor on the hub;
Depress the “hub – disc” assembly;
Dismount the three ball joints by means PF 476 and take out the steering knuckle.
R
EMOUNTING
Position and press the steering knuckle on the “ hub – disk “assembly ,after previously having
introduced a grease supply.
Mount the “hub – disk - steering knuckle ”assembly, by coupling the ball joints and tighten
their nuts to the required moment.
Mount the transmission gear by means of the PF 236 device.
Mount and tighten:
- the transmission nut;
- the brake caliper support and the mud flap;
- the brake caliper.
Mount the wheel, get the vehicle down from the elevator, recover the PF 509 crossbar.
Press the brake pedal several times in order to bring the brake caliper piston in contact with
the brake pads
When replacing the steering knuckle, check and adjust the steering box position, the parallel-
ism, distribution.
31
FRONT BEARING ELEMENTS
31 - 23
STEERING KNUKLE
STEERING KNUKLE - CHECKING
SPECIAL
TO OLS
:
D
ENO MINATION
C
ODE
Steering knuckle checking device
PF 496
The steering knuckle is dismounted off the motor car.
Dismount the inner bearing of the steering knuckle.
In its seat, place the pin (C) of the PF 496 checking device, and place mandrels (A) and (B)
in the suspension ball joint seats.
In this situation, the side (E) of the steering knuckle should be parallel to the checking device
front side, and the seat of the steering ball joint should get into the device bore.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст