SsangYong Rodius (2013 year). Service manual — part 70
09-3
1451-01
1. SPECIFICATION
Alternator
Crankshaft pulley : Alternator pulley
1 : 2.94
Normal output (idling/2200 rpm)
70/140A
Regulator voltage
14.6 V
Brush
Length
12.5mm
Wear limit
7mm
Battery
Type
MF
Capacity
90 AH
Unit
Description
Specification
09-4
2. INSPECTION
1) Alternator Output Test
Item
How to check
DTC set value / Action
Output
current
B terminal
current
Rotor
coil
resistance
D terminal
voltage
Disconnect the cable connected to the B
terminal on the alternator. Connect one
end of the ammeter to the B terminal and
the other end to the cable connected to
the B terminal.
Measure the maximum output value.
(Maintain the engine speed between
2,500 and 3,000 rpm.)
(Turn the headlamp and all the electrical
switches on.)
1.
2.
Pass: If the measured current is 45
A or higher.
Fail: If the measured current is less
than 45 A.
Check the current of the B
terminal.
-
-
-
Move the gear selector lever to the neutral
position.
Maintain the engine speed at 2,500 rpm
with the vehicle unloaded.
(Turn all the electrical switches off.)
1.
2.
Open circuit: If the measured
current is 5 A or higher.
-
Disconnect the negative cable from the
battery.
Remove the B terminal and turn off the
ignition switch.
Measure the resistance between the L and
F terminals with an ohmmeter.
1.
2.
3.
Pass: If the measured resistance is
between 3 and 6 Ω.
Faulty rotor coil or slip ring: If the
measured resistance is less than 3
Ω or greater than 6 Ω.
-
-
Connect the B terminal wiring.
Measure the voltage with the engine
running.
1.
2.
Specification: 12.5 V to 14.5 V
Faulty IC regulator or field coil: If
the measured voltage is 14.5 V or
higher.
-
-
Disconnect the negative battery cable.
Connect the negative cable again after connecting the ammeter.
-
-
09-5
1451-01
2) Troubleshooting for Alternator
Item
Cause
Action
Overcharged
battery
Defective alternator voltage regulator
Replace the alternator
Defective voltage detection wiring
Replace the alternator
Defective voltage detection wiring
Repair or replace
Discharged battery
Loose alternator drive belt
Adjust the belt tension or replace
Poor connection of related circuit or
open circuit
Retighten the loose connection or
repair open circuit
Defective alternator voltage regulator
Replace the alternator
Terminated battery
Replace the battery
Defective ground
Repair
Charge warning
lamp does not
come on when
turning on ignition
switch with engine
stopped
Defective alternator voltage regulator
Replace the alternator
Open circuit in charge warning lamp,
fuse or wiring
Replace or repair the charge
warning lamp or fuse
Defective ignition switch
Replace the ignition switch
Defective ground of alternator circuit
Repair
Charge warning
lamp is not turned
off after starting
engine
Defective alternator voltage regulator
Replace the alternator
Corroded or worn battery cable
Repair or replace the battery cable
Loose alternator drive bel
Replace the batteryAdjust the belt
tension or replace the belt
Defective wiring harness
Repair or replace
Warning lamp does
not go off even
after starting the
engine
Corrosion or damage of
battery cable
Repair or replace the
battery cable
Loose alternator drive belt
Adjust the belt tension or
replace the belt
Defective wiring harness
Repair or replace
Overcharged
battery
Defective voltage regulator of alternator
Replace the alternator
Defective voltage detecting wiring
Repair or replace
09-6
3) Checking Battery
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст