SsangYong Korando III (2010 year). Service manual — part 477
05-40
Status
Message
Operating condition
Impossible to
determine tire
pressure
Pressure of the tire displayed as “--” when not
possible to determine tire pressure correctly
* At initial start, the tire pressure can be displayed
after 10 minutes of driving at speed of 20 km/h or
higher
Correct tire pressure
The specified tire pressure is based on a cold tire
with the vehicle unloaded (no occupant); 32 psi at
20℃.
Lower than minimum
tire pressure
Corresponding status lamp comes on if tire
pressure is 24 psi or less
Excessive tire
pressure
Corresponding status lamp blinks with shading
reverse at interval of 0.4 seconds if tire pressure is
50 psi or higher
Low tire pressure
Corresponding status lamp comes on if tire
pressure is 24 psi or less
Sudden tire pressure
loss
Corresponding status lamp blinks with shading
reverse at interval of 0.4 seconds if tire pressure
changes more than 3 psi per 1 minute at speed of 0
km/h or above.
Imbalance between
left and right tire
pressure
Corresponding status lamps blink alternately at
interval of 1.0 second if tire pressure differs by more
than 4 psi in the left and right tires while driving for
more than 10 minutes
Supervision type
▶
Pressing the TRIP switch at the illumination brightness mode changes the screen to the tire pressure
display mode.
If the tire pressure is normal, “Tire Pressure OK” is displayed. If the tire pressure is abnormal,
the tire in question blinks then comes on depending on how the abnormality is severe on the display
screen.
-
-
05-41
8010-01
(6) Ambient Air Temperature Mode
The ambient air temperature is calculated and displayed.
This is displayed on both STD and SVC class, regardless of FATC type (automatic or manual).
For SVC class, the driver set only the unit between ℃ and ℉ on the DOT LCD, the ambient
temperature is displayed on the SEG LCD.
-
-
-
Function
Signal
Remark
Display type
3 digits LCD
Display range
Resolution
1℃(1℉)
-30℃ ~ 90℃
(-22℉~ 194℉)
-31℃ ~ -33℃
: maintain 30℃
91℃~93℃
: maintain 90℃
-
-
-
<STD>
<SVC>
05-42
8) Buzzer
Specifications
▶
Function
Signal
Part name
PKM17EPP-2002-B0 (MURATA, Piezoelectric Sound Components)
Permitted input voltage
25 VP-P or less
Operating temperature
-20˚C to +70˚C
Storage temperature
-30˚C to +80˚C
Sound pressure level
70 dB/min (3 Vp-p, 2 kHz, square wave, 10 cm)
Capacitance
19.0 nF ±30% (120 Hz)
Priority of instrument cluster buzzer output
▶
If there are multiple signals at a time, the operation should be completed by the priority.
Priority
Item
Buzzer output
time
Operating condition
ON
OFF
1
PAS
See PAS
2
ESP
0.1sec
0.1sec
Instrument cluster buzzer output signal is
received from ABS/ESP
3
Engine overheat
warning lamp
0.5sec
0.5sec
Engine overheats (120℃ or higher)
4
Water separator
warning light
0.5sec
0.5sec
Water separator warning light ON with
IGN ON
5
Parking brake
2.8sec
1.5sec
Parking brake applied depending on
vehicle speed
05-43
8010-01
9) PAS (Parking Aid System)
(2) Self Diagnosis Mode
Operating conditions
▶
Fail condition (However, no obstacle should be within 30 cm)
1. The signal wire is open
2. The power wire (+ and -)is open
-
Buzzer interval during self diagnosis
▶
(1) Sensor Operating Process
The ultrasonic sensors transmit ultrasonic waves and receive the reflected waves from an obstacle to
detect it in the following order: L → C → R.
Self diagnosis is performed once when the ignition is switched on (gear shift lever in "R" position). If the
system is defective (Fail) due to open sensor or communication problem, the information for the failed
sensor is sent to the instrument cluster.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст