SsangYong Korando III (2010 year). Service manual — part 465
04-24
9. ESCL CONTROL
ESCL lock/unlock is not performed at ESCL virgin mode.
The SKM does not carry out the ESCL LOCK control if the engine is running with IGN ON or the
vehicle speed is 3 km/h or higher.
All the ESCL functions including START/STOP switch is disabled during anti-scanning flag bit set.
-
-
-
If the smart key is pressed with power off, the electric steering motor performs the steering column
unlock. In some cases, power transition is carried out to ACC or IGN ON.
If the power transition and start is not possible after retry to LOCK or UNLOCK operation, the power
transition and start is not still possible after automatic retry and the warning lamp comes on.
-
-
1) ESCL LOCK Control
When the ESCL is unlocked and the followings are met at normal condition:
If the driver door is open or closed with ignition key OFF, the electric steering motor performs the
steering column lock.
If the theft deterrent mode is activated by the LOCK signal from the passive or REKES key when
turning the ignition key from “ON” position to “OFF” position, the ESCL LOCK is performed.
The ESCL LOCK is performed after 60 seconds since the ignition key is turned to B+ from
“ON” or “ACC” position.
-
-
-
2) ESCL UNLOCL Control
When the ESCL is locked and the followings are met at normal condition:
04-25
8712-03
3) ESCL Retry Control
ESCL operation is not possible if Bolt is “Failure”.
When the UNLOCK retry occurs after ESCL LOCK command, the ESCL LOCK is performed.
1.
2.
The UNLOCK retry is possible up to 2 times automatically. If the UNLOCK retry occurs 3 times in
succession, the ESCL NOT LOCKED warning is triggered.
Reactivates when the ESCL LOCK conditions are met.
-
-
When the LOCK retry occurs after ESCL UNLOCK command, the ESCL UNLOCK is performed.
4.
The LOCK retry is possible up to 2 times automatically. If the LOCK retry occurs 3 times in succession,
the ESCL JAM warning is triggered.
Reactivates when the ESCL UNLOCK conditions are met by pressing the START/STOP switch.
-
-
When the UNLOCK retry occurs after ESCL UNLOCK command, the command will be overridden
without retry.
5.
After the command is overridden, the ESCL JAM warning is triggered.
Reactivates when the UNLOCK conditions are met by pressing the START/STOP switch after
ESCL LOCK.
-
-
When the LOCK retry occurs after ESCL LOCK command, the command will be overridden without
retry.
3.
ESCL NOT LOCKED warning is triggered.
Reactivates when the UNLOCK conditions are met by pressing the START/STOP switch.
-
-
04-26
10. START/STOP SWITCH CONTROL
1) Power Status
Ignition status indicator on START switch
▶
Status
Turning-ON conditions
OFF
IGN OFF, IGN ON & engine ON
Green
Engine can be started by START/STOP switch operation/Engine is cranking
(IGN OFF & brake switch ON, ACC ON & brake switch ON, IGN ON & brake
switch ON)
Amber
ACC ON
Red
IGN ON & engine OFF, error
START switch indicator output
▶
Powersta
tus
Power OFF
ACC ON
IGN
ON
Engine
start
status
Engine
can be
started
Error
Remarks
Door
closed
Door
open
Figure
Indicator
status
OFF
OFF
Amber
Red
OFF
Green
Red
Flash
Illuminatio
n
control
OFF
TIME
Controlled by SKM
LED
The indicator flashes 5 times at intervals of 0.5 sec. ON/0.5 sec. OFF when an error occurs.
When all the doors are closed with B+, the indicator does not flash.
-
-
START/STOP switch indicator control
▶
START/STOP switch indicator
ON
OFF
Door coupled function
When the driver door is opened, the indicator comes
on (the indicator remains on while the door is open).
When the room lamp is turned off, the indicator goes
out immediately.
The indicator goes out 10 seconds after the driver door
is closed.
The indicator is reset when the driver door is opened.
Tail lamp coupled function
-
1)
2)
3)
4)
-
04-27
8712-03
11. SKM WARNING CONTROL
(1) Smart Key Not Detected Warning
With ACC ON
▶
Smart key not detected warning deactivation conditions
- ACC OFF, IGN1 ON, Smart key detected
IGN ON and engine running
▶
Smart key not detected warning deactivation conditions
- IGN1 OFF, Smart key detected, Door open
Any door except the driver door is opened and then closed.
The SKM starts to identify a smart key by using the interior antenna after confirming that all the doors
are closed through CAN communication with the BCM.
When no smart key is found, the SKM sends the smart key not detected warning signal to the BCM
and instrument cluster through B-CAN.
The BCM activates the buzzer for up to 10 seconds at intervals of 0.5 sec. ON/0.5 sec. OFF and
turns on the smart key warning indicator on the instrument cluster.
If a smart key is found, no operation is performed.
1.
2.
3.
4.
5.
Any door except the driver door is opened and then closed.
The smart key not detected warning is not activated.
- Smart key searching using the interior antenna → No smart key found → The SKM sends
the smart key not detected warning signal to the BCM and instrument cluster through B-CAN.
The smart key not detected warning is activated.
- Smart key searching at intervals of 3 seconds using the interior antenna.
1.
2.
3.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст