SsangYong Stavic / SsangYong Rodius (2005 year). Service manual — part 13
1B-31
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
Removal & Installation Procedure
1. Remove the drain plug and drain the oil completely.
2. Unscrew the bolts and remove the oil pan and gasket.
Notice
Arrange the bolts according to each size.
3. Clean the inside of oil pan and sealing surface, then apply
the sealant.
4. Replace the gasket with new one.
5. Install the oil pan with gasket, and tighten each bolt in
specified torque.
6. Check for oil leaks while running the engine.
M8 X 40, 4 pieces
M6 X 85, 3 pieces
M6 X 35, 3 pieces
M6 X 22, 6 pieces
M6 X 20, 28 pieces
Others
1B-30
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
OIL PAN
1. Gasket . . . . . . . . . . . . . .. Replace
2. Bolt (M6 x 22, 6 pieces)
. . . . . . . . . .. 9 ~ 11 Nm (80 ~ 97 lb-in)
3. Drain plug . .. 22.5 ~ 27.5 Nm (16.6 ~ 20.3 lb-ft)
4. Bolt (M6 x 20, 22 pieces)
. . . . . . . . . .. 9 ~ 11 Nm (80 ~ 97 lb-in)
5. Bolt (M6 x 85, 3 pieces)
. . . . . . . . . .. 9 ~ 11 Nm (80 ~ 97 lb-in)
6. Bolt (M8 x 40, 4 pieces)
. . . . . ... 22.5 ~ 27.5 Nm (16.6 ~ 20.3 lb-ft)
7. Bolt (M10) . . . . . . . . ... 40 Nm (30 lb-ft)
8. Oil pan
1B-31
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
Removal & Installation Procedure
1. Remove the drain plug and drain the oil completely.
2. Unscrew the bolts and remove the oil pan and gasket.
Notice
Arrange the bolts according to each size.
3. Clean the inside of oil pan and sealing surface, then apply
the sealant.
4. Replace the gasket with new one.
5. Install the oil pan with gasket, and tighten each bolt in
specified torque.
6. Check for oil leaks while running the engine.
M8 X 40, 4 pieces
M6 X 85, 3 pieces
M6 X 35, 3 pieces
M6 X 22, 6 pieces
M6 X 20, 28 pieces
Others
1B-32
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
ENGINE MECHANICAL
M162 GSL ENG SM - 2005.7
TIMING GEAR CASE COVER
Preceding Work: Removal of cylinder head front cover
Removal of generator bracket
Removal of tensioning device
Removal of belt pulley and vibration damper
1. Bolt (M8 x 60, 3 pieces)
. . . . . ... 22.5 ~ 27.5 Nm (16.6 ~ 20.3 lb-ft)
2. A/C bracket
3. Bolt (M8 x 65, 3 pieces)
. . . . . ... 22.5 ~ 27.5 Nm (16.6 ~ 20.3 lb-ft)
4. Bolt (M8 x 40, 1 piece)
. . . . . ... 22.5 ~ 27.5 Nm (16.6 ~ 20.3 lb-ft)
5. Bolt (M8 x 60, 1 piece)
. . . . . ... 22.5 ~ 27.5 Nm (16.6 ~ 20.3 lb-ft)
6. Seal
7. Timing gear case cover
8. Roll pin
9. Bolt (M6 x 22, 6 pieces)
. . . . . . . . . .. 9 ~ 11 Nm (80 ~ 97 lb-in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст