SsangYong Stavic / SsangYong Rodius (2005 year). Service manual — part 126
DI06-31
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
COOLING SYSTEM
DI ENG SM - 2004.9
3. Remove the drain plug and seal in the cylinder block and
drain the coolant.
4. Replace the seal with new one and install the drain plug.
Installation Notice
5. Install the drain plug in bottom of radiator.
6. Add the coolant through the coolant reservoir.
7. Warm up the engine until the thermostat begins to open
and check if the coolant level is at “FULL” mark on the
reservoir. Add if necessary.
2. Loosen the drain plug in bottom of radiator and drain the
coolant.
1. Release the pressure from coolant reservoir by loosening
one notch of coolant reservoir cap, and then remove the
cap.
Draining and Adding of Coolant
Tightening torque
30 Nm
Notice
Scalding hot coolant and steam could be blown out
under pressure, which could cause serious injury.
Never remove the coolant reservoir cap when the
before the temperature goes down below 90°C.
Notice
Collect the drained coolant with a proper container.
Notice
• Keep the coolant mixture ratio of 50:50 (water : anti-
freezer).
• Add the coolant until the water flows out through
the overflow hose.
DI06-32
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
COOLING SYSTEM
DI ENG SM - 2004.9
PREHEATING SYSTEM
Preheating relay
Glow plug
ECU
Glow indicator (meter cluster)
DI06-33
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
COOLING SYSTEM
DI ENG SM - 2004.9
Y220_06069
OVERVIEW
Glow plug is installed on the cylinder head (combustion chamber) in the D27DT preheating control unit system. Cold
starting performance has improved and exhaust gas during cold starting has reduced.
ECU receives coolant temperature and engine speed to control; after monitoring the engine preheating/after heating and
glow plug diagnosis function, the fault contents will be delivered to ECU.
• Engine preheating/after heating functions
• Preheating relay activation by ECU controls
- Senses engine temperature and controls the preheating/after heating time
- Glow indicator
• K-LINE for information exchanges between preheating unit and ECU
- Transmits preheating unit self-diagnosis results to ECU
- Transmits glow plug diagnosis results and operating status to ECU
PREHEATING RELAY
Structure
K-LINE #1
(ECU 34)
IG1
Power terminal
Glow plug
control signal
(ECU 113)
Ground terminal
B+main wire
(12V)
Glow plug
terminal
DI06-33
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
COOLING SYSTEM
DI ENG SM - 2004.9
Y220_06069
OVERVIEW
Glow plug is installed on the cylinder head (combustion chamber) in the D27DT preheating control unit system. Cold
starting performance has improved and exhaust gas during cold starting has reduced.
ECU receives coolant temperature and engine speed to control; after monitoring the engine preheating/after heating and
glow plug diagnosis function, the fault contents will be delivered to ECU.
• Engine preheating/after heating functions
• Preheating relay activation by ECU controls
- Senses engine temperature and controls the preheating/after heating time
- Glow indicator
• K-LINE for information exchanges between preheating unit and ECU
- Transmits preheating unit self-diagnosis results to ECU
- Transmits glow plug diagnosis results and operating status to ECU
PREHEATING RELAY
Structure
K-LINE #1
(ECU 34)
IG1
Power terminal
Glow plug
control signal
(ECU 113)
Ground terminal
B+main wire
(12V)
Glow plug
terminal
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст