SsangYong Stavic / SsangYong Rodius (2005 year). Service manual — part 104
DI04-9
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
EXHAUST SYSTEM
DI ENG SM - 2004.9
Diagnosis and Maintenance for Turbo Charger System
Cautions During Driving
The following lists cautions to take during test drive and
on the turbo charger vehicle, which must be considered
during the operation;
1. It’s important not to drastically increase the engine
rpm starting the engine. It could make rotation at
excessive speed even before the journal bearing is
lubricated and when the turbo charger rotates in poor
oil supply condition, it could cause damage of bearing
seizure within few seconds.
2. If the engine is running radically after replacing the
engine oil or oil filter brings poor oil supply condition.
To avoid this, it’s necessary to start off after idling
the engine for about 1 minute allowing oil to circulate
to the turbo charger after the replacement.
3. When the engine is stopped abruptly after driving at
high speed, the turbo charger continues to rotate in
condition where the oil pressure is at ‘0’. In such
condition, an oil film between the journal bearing and
the housing shaft journal section gets broken and
this causes abrasion of the journal bearing due to the
contact of metal parts. The repeat of such condition
significantly reduces life of the turbo charger.
Therefore, the engine should be stopped possibly in
the idle condition.
Notice
After string for long period of time during winter
season or in the low temperature condition where
the fluidity of engine oil declines, the engine,
before being started, should be cranked to
circulate oil and must drive after checking the oil
pressure is in normal condition by idling the
engine for few minutes.
Inspection of Turbo Charger
When problem occurs with the turbo charger, it could cause
engine power decline, excessive discharge of exhaust gas,
outbreak of abnormal noise and excessive consumption
of oil.
1. Inspection when installed
- Check the bolts and nuts for looseness or missing
- Check the intake and exhaust manifold for
looseness or damage
- Check the oil supply pipe and drain pipe for
damages
- Check the housing for crack and deterioration
2. Inspection of turbine in turbo charger
Remove the exhaust pipe at the opening of the turbine
and check, with a lamp, the existence of interference
of housing and wheel, oil leakage and contamination
(at blade edge) of foreign materials.
- Interference: In case where the oil leak sign exists,
even the small traces of interferences on the
turbine wheel mean, most of times, that abrasion
has occurred on the journal bearing. Must inspect
after overhauling the turbo charger.
- Oil Leakage: Followings are the reasons for oil
leakage condition;
• Problems in engine: In case where the oil is
smeared on inner wall section of the exhaust
gas opening.
• Problems in turbo charger: In case where the
oil is smeared on only at the exhaust gas
outlet section.
Notice
Idling for long period of time can cause oil
leakage to the turbine side due to low pressure of
exhaust gas and the rotation speed of turbine
wheel. Please note this is not a turbo charger
problem.
DI04-10
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
EXHAUST SYSTEM
DI ENG SM - 2004.9
- Oil Drain Pipe Defect
In case where oil flow from the turbo charger
sensor housing to the crank case is not smooth
would become the reason for leakage as oil builds
up within the center housing. Also, oil thickens
(sludge) at high temperature and becomes the
indirect reason of wheel hub section. In such case,
clogging and damage of the oil drain pipe and the
pressure of blow-by gas within the crank case
must be inspected.
- Damages from Foreign Materials
When the foreign materials get into the system,
it could induce inner damage as rotating balance
of the turbo charger gets out of alignment.
Inspection of Turbine
Thoroughly check the followings.
Notice
Must absolutely not operate the turbo charger with the
compressor outlet and inlet opened as it could damage
the turbo charger or be hazardous during inspection.
- Interference: In case where is trace of interference or
smallest damage on the compressor wheel means,
most of times, that abrasion has occurred on the
journal bearing. Must inspect after the overhaul.
- Oil Leakage: The reason for oil leakage at the
compressor section is the air cleaner, clogged by
substances such as dust, causes the compressor
inlet negative pressure;
A. Rotating in high speed at no-load for extended
period of time can cause oil leakage to the
compressor section as oil pressure within the
center housing gets higher than pressure within
the compressor housing.
B. Overuse of engine break (especially in low gear)
in down hill makes significantly low exhaust gas
energy compared to the time where great amount
of air is required during idling conditions of the
engine. Therefore, amount of air in the
compressor inlet increases but the turbo charge
pressure is not high, which makes negative
pressure at the compressor section causing the
oil leakage within the center housing.
Notice
No problem will occur with the turbo charger if
above conditions are found in early stage but oil
leaked over long period of time will solidify at
each section causing to breakout secondary
defects.
- Damages by foreign materials: In case where the
compressor wheel is damaged by foreign materials
requires having an overhaul. At this time, it’s
necessary to check whether the foreign materials have
contaminated intake/exhaust manifold or inside of
engine.
DI04-11
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
EXHAUST SYSTEM
DI ENG SM - 2004.9
Path of Turbo Charger Defect
The following tries to understand the defects that can occur with vehicle installed with the turbo charger and to manage
the reasons of such defects.
1. In case where oil pan/oil pipe has been contaminated, oil filter is defected and where
adhesive of gaskets has been contaminated into the oil line.
Contamination of Oil
Journal Bearing
Damage or Wear
Clogging of Oil
Passage
Metal Contact
Poor Oil Supply
Shaft Journal Bearing Wear
Rotor Wear
Seal Wear at
Exhaust System
Interference of
Turbine and Com-
pressor Components
Oil Leakage
Seal Wear at Intake
System
Abnormal Noise
Lack of Power/Poor
Acceleration (Lack of
Turbo Charged Pressure)
Check Exhaust Gas Pipes
Check Booster Pressure
Control Valve
DI04-12
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
EXHAUST SYSTEM
DI ENG SM - 2004.9
2. Oil Pump Defect: Rapid over-loaded driving after replacing oil filter and oil and clogging of oil
line.
Poor Oil Supply
Metal Contact of Shaft /Journal Bearing/
Center Housing Inner Part
Journal Bearing/Center Housing Inner Part
Wear/Seizure
Seal Wear at Exhaust
System
Interference of Turbine and
Compressor Components
Oil Leakage
Seal Wear at Intake
System
Abnormal Noise
Melt down of Bearing to Turbine Wheel Journal
Rotor Rotational Movement
Lack of Power/Poor
Acceleration (Lack of
Turbo Charged Pressure)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст