SsangYong Stavic / SsangYong Rodius (2005 year). Service manual — part 308
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
46
DC 5-SPEED AUTOMATIC TRANSMISSION
STAVIC - 2004.09
4A
Description
Diagnostic
Initiating the starter relay
RPM sensor N2
RPM sensor voltage supply
1-2, 4-5 solenoid valve
3-4 solenoid valve
2-3 solenoid valve
Lockup clutch solenoid valve
TCU voltage supply
Ground
RPM sensor ground
ATF temperature, Starter lock-out contact
RPM sensor N3
Modulating pressure solenoid valve
Shift pressure solenoid valve
Each solenoid valve voltage
CAN Low
CAN High
Connected to
Diagnostic connector pin No.11
Starter relay
13-pin plug No.3
13-pin plug No.7
13-pin plug No.13
13-pin plug No.9
13-pin plug No.11
13-pin plug No.11
-
-
13-pin plug No.12
13-pin plug No.4
13-pin plug No.1
13-pin plug No.2
13-pin plug No.10
13-pin plug No.6
ECM, HECU, selector lever unit, instrument panel
ECM, HECU, selector lever unit, instrument panel
Pin No.
1
7
12
13
14
15
16
17
29
30
33
34
35
36
37
38
L
H
Connector arrangement and pin functions
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Connector A
Connector B
Connector A
Connector B
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
47
DC 5-SPEED AUTOMATIC TRANSMISSION
STAVIC - 2004.09
4A
OTHER FUNCTIONS
OIL LEVEL CONTROL
Function
This is the function that closes the opening between oil chamber and planetary gear set chamber, so that the gear set
does not splash in oil if the oil level rises.
The lubricating oil flowing continuously out of the gear sets returns through the opening (2) into the oil chamber. If the oil
level rises, the oil forces the float (1) against the housing.
The float separates the oil chamber from the gear set chamber. The lubricating oil which escapes further from the gear
sets is thrown against the housing wall by the rotating parts and flows now through the upper opening (arrow) back into
the oil chamber.
Reduction of power losses and prevention of fluid loss from the transmission at high fluid level.
1. Float
2. Opening
A. Oil chamber
B. Planetary gear set chamber
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
48
DC 5-SPEED AUTOMATIC TRANSMISSION
STAVIC - 2004.09
4A
Oil Check and Specification
Cap
Lock pin
Lock pin
Checking and adding Tip
A. Place the vehicle on level ground. Pull out the lock
pin and remove the cap (add 4 to 5 liter if oil has
been completely drained out).
B. Place the selector lever to “P” position. Start the
engine and leave it idling (add 2.5 liter if oil has been
completely drained out).
C. Warm the engine up while moving the selector lever
to all positions. Check if the oil temperature is approx.
80°C with a scanner (apply the parking brake).
: Selector lever position - R or D
D. Check the oil level with oil dipstick while engine is
running in “P” position.
E. Check several times with attention, and add or drain
the oil as required.
Automatic transmission fluid capacity and
specification
Fluid capacity
Specification
Approx. 8
Fuchs ATF 3353 or Shell ATF 3353
[Notice]
1) Use only specified ATF oil.
2) Measure the ATF oil temperature as the shift lever is in
“R” or “P”.
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
49
DC 5-SPEED AUTOMATIC TRANSMISSION
STAVIC - 2004.09
4A
SHIFT ROD ADJUSTMENT
Adjustment
A. Disengage the shift rod from range lever and place the range lever at “D” position.
B. Place the selector lever at “D” position.
C. Insert the shift rod into range lever and tighten nut.
D. Check if the indication lamp in meter cluster indicates correct gear position while moving the selector lever to “P”,
“R”, “N”, and “D” position.
E. Check if the engine can be started at selector lever “P” or “N” position.
1. Range lever
2. Shift rod
3. Selector lever
D. “D” range
P. “P” range
[Notice]
Lock the selector lever so that it will not move.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст