SsangYong Actyon Sports II. Service manual — part 105
07-3
7810-01
1. SPECIFICATIONS
Unit
Item
Specification
Wiper motor
Rated voltage
DC 12 V
Operating voltage
DC 10 to 15 V
Lowest operating voltage
DC 8 V or less
Low revolutions
46 ± 5 RPM
High revolutions
70 ± 9 RPM
Wiper arm and blade
Wiper arm length
Driver
508 mm
Passenger
537 mm
Wiper blade
length
Driver
550 mm
Passenger
475 mm
Rain sensor
Operating voltage
DC 9 to 16 V
Load
Max. 200 mA (relay load)
Operating temperature
-30˚C to 85˚C
Mounting location
Top center of inner side of windshield
glass
Washer reservoir tank
Volume
3.0 L
07-4
2. MAJOR CHANGES
Wiper blade
- Changed from conventional type to aero blade type
- No change in wiper blade dimension and wiper arm
Driver: 550 mm (22 inches)
Driver: 550 mm (22 inches)
Passenger: 475 mm (19 inches)
Passenger: 475 mm (19 inches)
07-5
7810-01
3. CAUTIONS ON RAIN SENSOR
When the wiper switch is in the AUTO position, the wiper will operate for 1 cycle if the initial engine
start is made. This may cause the wiper blades to wear prematurely. Therefore, other than rainy days,
set the switch to the OFF position. Especially during the winter time, check if the wiper blades are not
frozen to the windshield.
Operating the wiper with the blades frozen can damage the wiper motor.
If you operate the wipers when the windshield is dry without spraying washer fluid, the windshield can
be scratched and the wiper blades can wear prematurely. Use the wiper with the washer fluid when
the windshield is dry.
When it does not rain, turn the wiper switch to the OFF position.
Turn the wiper switch to the OFF position before any car wash to avoid unwanted operation of the
wipers.
-
-
-
-
When cleaning the windshield over the sensor with damp clothes, the wiper may operate suddenly. It
could cause serious injury. Make sure to place the wiper switch to the OFF position and ignition
switch OFF when not in use.
Irregular operation (abrupt operation)
▶
Check if the sensor is off the position.
Check if the rain sensor cover is securely installed.
Check if the customer is familiar to how to control the wiper sensitivity.
Check if the wiper sensitivity control is set to the FAST side (step 5).
Check the wiper blade for wear.
If the wiper blade cannot wipe the glass uniformly and clearly, it may cause the rain sensor to work
irregularly. Therefore, in this case, replace the wiper blade with a new one.
-
-
-
-
07-6
1. OVERVIEW
The wiper & rain sensor system consists of the multifunction wiper switch, windshield wiper motor and
linkage, wiper arm and blade, rain sensor, wiper relay (LO/HI) and washer tank. The rain sensor does
not directly operate the rain sensing wiper and it sends only the data of the rainfall to the STICS. The
basic operation of the wiper and washer is controlled by the STICS according to the signal regarding the
multifunction switch operation modes (MIST, AUTO, LO/HI, washer, sensitivity adjustment).
Layout
▶
Windshield wiper motor & linkage
When the driver operates the switch so that
the wiper motor is activated, the linkage
converts the rotary motion to reciprocating
motion and transfers it to the wiper arm.
Windshield wiper arm & blade
It receives the power from the wiper linkage
and does a reciprocating motion (left to right).
Washer nozzle
Installed on both sides of the cowl grille
assembly (one on each side). Sprays washer
fluid in fan-shape to cover the windshield
area as much as possible.
Washer reservoir tank
Tank that supplies washer fluid to front
washer system.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст