SsangYong Musso. Service manual — part 282
M161 ENGINE MECHANICAL 1B2-55
Arrangement of the Thrust Bearing and the Main Bearing
1 - 8
Weight Balance/Color Marking Point
j1 - j5
Journal Main Bearing #1 - #5
z
Color Dot Marking
The color dot marking are put on the 1 , 2 , 4 , 6
, 8 , and it indicates the diameter of crankshaft journal
by color as below.
A Crankcase Side
B Bearing Cap Side (Oil Pan Side)
1 Upper Main Bearing
2 Upper Thrust Bearing
3 Crankshaft
4 Lower Main Bearing
5 Lower Thrust Bearing
1B2-56 M161 ENGINE MECHANICAL
Selection of Crankshaft Main Bearing
1. Crankcase Side
There are seven punching marks on the mating surface
to oil pan. This mark is correspondent to the bearing
distinguished by color. Select the relevant bearing
according to the punching mark when repaired.
2. Crankshaft Bearing Cap Side
Select the crankshaft main bearing according to the
marking letter on the crankshaft main journal when
repaired.
Color Dot Marking
Blue
Yellow
Red
White
Violet
Crankshaft Journal Diameter (mm)
57.960 - 57.965
57.955 - 57.960
57.950 - 57.955
57.945 - 57.950
57.940 - 57.945
Punching Mark
•
••
•••
Bearing Color Selected
Blue
Yellow
Red
Marking Letter
B
Y
R
W
V
Bearing Color Selected
Blue
Yellow
Red
White
Violet
Service Data
Unit : mm
Crankshaft
Bearing Jour-
nal Diameter
Crankshaft
Bearing
Diameter
Crankshaft
Journal Width
at fit bearing
Connecting Rod
Bearing Journal
Diameter
Connecting
Rod Bearing
Jourmal Width
Standard size
1st repair size
2nd repair size
3rd repair size
4th repair size
57.950-57.965
57.700-57.715
57.450-57.465
57.200-57.215
56.950-56.965
58
24.50-24.533
47.94-47.96
47.75
47.50
47.25
47.00
27.958-28.042
Crankshaft Standard
and Repair Size
-
-
-
M161 ENGINE MECHANICAL 1B2-57
Installation Notice
z
Make sure the crankshaft bearing cap properly seated
in place in the crankcase side. When perfectly
installed, the projected part (arrow) locates in the left
side (intake manifold side).
z
Assemble so that the projected part of the cap and
crankcase face the same direction.
Removal & Installation Procedure
1. Unscrew the connecting rod bearing cap bolt and remove
the bearing cap.
Installation Notice
2. Unscrew the crankshaft bearing cap bolts and separate
the upper and lower bearing shells and thrust washers.
Installation Notice
z
Remove the bearing cap from front (pulley side) to
rear.
z
Make sure that the upper and lower bearing shells do
not change each other and coat with engine oil.
z
The oil grooves (arrows) in the thrust washers must
face outward and insert the thrust bearing into the
bearing cap.
z
There are five kinds of thrust washers by thickness.
Select the proper washer when repaired.
3. Remove the crankshaft.
4. Installation should follow the removal procedure in the
reverse order.
5. After completion of the installation, check for the rotating
condition of the crankshaft.
z
Make sure that the upper and lower bearing shells do
not change each other.
z
Coat the bearing shell with engine oil.
z
Install the bearing cap according to the consecutive
number.
Part No. : 601 030 00 62
2.15 mm
Part No. : 601 030 01 62
2.20 mm
Part No. : 601 030 02 62
2.25 mm
Part No. : 601 030 03 62
2.30 mm
Part No. : 601 030 04 62
2.40 mm
Tightening Torque
40 Nm + 90°
Tightening Torque
55 Nm + 90°
1B2-58 M161 ENGINE MECHANICAL
Inspection
1. If the length ‘L’ of the crankshaft bearing cap bolt exceeds
63.8mm, replace it.
2. Make sure the crankshaft bearing cap is properly seated
on the cylinder block (arrows).
3. Measure and record the inner diameter of the crankshaft
bearing.
Notice
z
Measure at 2 points (1, 2).
z
Measure ‘A’,‘B’and ‘C’ as shown. If average value of
‘B’ and ‘C’is less than value ‘A’, then the average value
of ‘B’ and ‘C’ is actual average value. If average value
of ‘B’ and ‘C’ is more than value ‘A’is actual average
value.
4. Measure and record the diameter of the crankshaft
bearing journal.
Notice
z
Record the mean value when measured at 3 points
(A, B, C).
z
Measure the inner diameter of bearing and the
diameter of journal and if it is out of the standard data,
replace the bearing shell.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст