SsangYong Rexton. Service manual — part 525
ABS AND TCS 4E-65
SSANGYONG Y200
Step
1. Raise and suitably support the vehicle at the
corner being tested.
2. Turn the ignition to ON.
3. Install the scan tool to the data link connector
(DLC) and select “Wheel front left” to begin the
solenoid tests at that wheel. This will test both the
inlet and the outlet valves.
4. When the scan tool indicates “Pressure hold,”
press and hold the brake pedal until the end of the
test.
5. Have an assistant attempt to rotate the wheel.
Can the wheel be rotated?
1. Maintain pressure on the brake pedal.
2. When the scan tool indicates “Pressure increase,”
have an assistant attempt to rotate the wheel
again.
Can the wheel be rotated now?
1. Maintain pressure on the brake pedal.
2. When the scan tool indicates “Pressure release
on,” have an assistant attempt to rotate the wheel
again.
Can the wheel be rotated?
1. Release brake pedal pressure when the scan tool
indicates “Pressure release off”
2. Clear all DTCs.
3. Road test the vehicle.
Does the DTC set again?
1. Check the wiring harness and connector terminals
for an intermittent problem.
2. Repair any problem found.
Is the repair complete?
Replace the ABS unit.
Is the repair complete?
DTC 060/065 - Left Front Inlet and Outlet Valve Solenoid Fault
1
Action
Yes
No
Value
2
3
Go to Step 2
Go to Step 6
-
4
5
6
Go to Step 6
Go to Step 5
-
System OK
-
-
System OK
-
-
Go to Step 6
Go to Step 3
-
Go to Step 4
Go to Step 6
-
SSANGYONG Y200
4E-66 ABS AND TCS
DIAGNOSTIC TROUBLE COED (DTC) 070/075 - RIGHT FRONT INLET
AND OUTLET VALVE SOLENOID FAULT
YAD4E230
Circuit Description
The solenoid valve coil circuits are supplied with power
from the battery when the valve relay is energized.
Switched ground is provided by the electronic brake
control module (EBCM) to each coil.
Diagnosis
This procedure checks whether the right front inlet and
outlet valves are functioning.
Cause
•
A solenoid coil is open or shorted.
Action Taken When the DTC Sets
ABS is disabled, and the ABS warning lamp is turned
ON for the remainder of the ignition cycle. If the failure
is intermittent, the EBCM will enable the system at the
next ignition cycle and set a history DTC.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. This begins the test of the inlet valve
3. This tests the outlet valve.
ABS AND TCS 4E-67
SSANGYONG Y200
Step
1. Raise and suitably support the vehicle at the
corner being tested.
2. Turn the ignition to ON.
3. Install the scan tool to the data link connector
(DLC) diagnostic and select “Wheel front right” to
begin the solenoid tests at that wheel. This will test
both the inlet and the outlet valves.
4. When the scan tool indicates “Pressure hold,”
press and hold the brake pedal until the end of the
test.
5. Have an assistant attempt to rotate the wheel.
Can the wheel be rotated?
1. Maintain pressure on the brake pedal.
2. When the scan tool indicates “Pressure increase,”
have an assistant attempt to rotate the wheel
again.
Can the wheel be rotated now?
1. Maintain pressure on the brake pedal.
2. When the scan tool indicates “Pressure release
on,” have an assistant attempt to rotate the wheel
again.
Can the wheel be rotated?
1. Release brake pedal pressure when the scan tool
indicates “Pressure release off”
2. Clear all DTCs.
3. Road test the vehicle.
Does the DTC set again?
1. Check the wiring harness and connector terminals
for an intermittent problem.
2. Repair any problem found.
Is the repair complete?
Replace the ABS unit.
Is the repair complete?
DTC 070/075 - Right Front Inlet and Outlet Valve Solenoid Fault
1
Action
Yes
No
Value
2
3
Go to Step 2
Go to Step 6
-
4
5
6
Go to Step 6
Go to Step 5
-
System OK
-
-
System OK
-
-
Go to Step 6
Go to Step 3
-
Go to Step 4
Go to Step 6
-
SSANGYONG Y200
4E-68 ABS AND TCS
DIAGNOSTIC TROUBLE COED (DTC) 080/085 - LEFT REAR INLET AND
OUTLET VALVE SOLENOID FAULT
Circuit Description
The solenoid valve coil circuits are supplied with power
from the battery when the valve relay is energized.
Switched ground is provided by the electronic brake
control module (EBCM) to each coil.
Diagnosis
This procedure checks whether the left rear inlet and
outlet valves are functioning.
Cause(s)
•
A valve has failed.
•
A solenoid coil is open or shorted.
Action Taken When the DTC Sets
ABS is disabled, and the ABS warning lamp is turned
ON for the remainder of the ignition cycle. If the failure
is intermittent, the EBCM will enable the system at the
next ignition cycle and set a history DTC.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. This begins the test of the inlet valve
3. This tests the outlet valve.
YAD4E230
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст