SsangYong Rexton. Service manual — part 597
SSANGYONG Y200
5D2-36 TRANSFER CASE - TOD
TP Sensor Loss of Signal
Circuit Description
The transfer case control unit (TOD) receives throttle
position (TP) sensor signals from engine control module
(ECM) through CAN bus line.
Conditions for Setting the DTC
The transfer case control unit (TOD) can not receive
throttle position (TP) sensor signal from engine control
module (ECM). There is a bad communication between
TOD and ECM.
•
TOD is malfunction.
•
ECM is malfunction.
DIAGNOSTIC TROUBLE CODE (DTC) 1715
Action Taken When the DTC Sets
The TOD will illuminates 4WD CHECK indicator and
DTC is stored in TOD.
Diagnostic Aids
•
Check for poor connections of CAN bus line.
•
Check for ECM and TP sensor.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
2. This step decides the causal parts of the problem.
4. This step checks the ground condition.
6. This step checks the connection status.
Yes
Go to Step 2
Go to “TOD
Diagnostic
System
Check”
Refer to
Section
Engine
Go to Step 5
System OK
No
Go to “TOD
Diagnostic
System
Check”
Go to Step 3
Go to Step 4
-
Value
-
-
0
Ω
-
Step
1
2
3
4
Action
Was the TOD Diagnostic System Check performed?
1. Turn the ignition switch to OFF.
2. Connect the scan tool to data link connector (DLC)
and follow the directions given in the scan tool
manual.
3. Turn the ignition switch to ON and request engine
DTC.
Are there any engine DTC related throttle position (TP)
sensor?
1. Turn the ignition switch to OFF.
2. Disconnect the 18-pin connector from the transfer
case control unit (TOD).
3. Disconnect the gray connector from engine control
module (ECM).
4. Connect a digital ohmmeter between the following
TOD connector terminal and gray ECM connector
terminal.
•
B11 (TOD) and 37 (ECM)
•
B10 (TOD) and 38 (ECM)
•
B11 (TOD) and 24 (ECM)
•
B10 (TOD) and 23 (ECM)
Does the resistance of the all circuits measure within the
value specified?
Repair or replace any open wires, faulty connector, or
terminal.
Is the repair complete?
TRANSFER CASE - TOD 5D2-37
SSANGYONG Y200
Yes
System OK
System OK
No
Go to Step 6
-
Value
-
-
Step
5
6
Action
1. Replace the TOD.
2. Connect all connectors.
3. Request DTC with scan tool.
Is the repair complete?
Replace the ECU.
Is the repair complete?
SSANGYONG Y200
5D2-38 TRANSFER CASE - TOD
TP Sensor Out of Range
Circuit Description
The transfer case control unit (TOD) receives throttle
position (TP) sensor signals from engine control module
(ECM) through CAN bus line.
Conditions for Setting the DTC
D The transfer case control unit (TOD) receives throttle
position (TP) sensor signal from engine control module
(ECM), but the signal is out of the range.
There is a bad communication between TOD and ECU.
•
TOD is malfunction.
•
ECU is malfunction.
DIAGNOSTIC TROUBLE CODE (DTC) 1716
Action taken When the DTC Sets
The TOD will illuminates 4WD CHECK indicator and
DTC is stored in TOD.
Diagnostic Aids
Check for poor connections of CAN bus line.
Check for ECU and TP sensor.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
2. This step decides the causal parts of the problem.
4. This step checks the ground condition.
6. This step checks the connection status.
Yes
Go to Step 2
Go to “TOD
Diagnostic
System
Check”
Go to specific
engine DTC
diagnosis.
Go to Step 4
System OK
No
Go to “TOD
Diagnostic
System
Check”
Go to Step 2
Go to Step 5
-
Value
-
-
0
Ω
-
Step
1
2
3
4
Action
Was the TOD Diagnostic System Check performed?
1. Turn the ignition switch to OFF.
2. Connect the scan tool to data link connector (DLC)
and follow the directions given in the scan tool
manual.
3. Turn the ignition switch to ON and request engine
DTC.
Are there any engine DTC related throttle position (TP)
sensor?
1. Turn the ignition switch to OFF.
2. Disconnect the 18-pin connector from the transfer
case control unit (TOD).
3. Disconnect the gray connector from engine control
module (ECU).
4. Connect a digital ohmmeter between the following
TOD connector terminal and gray ECU connector
terminal.
•
B11 (TOD) and 38 (ECU)
•
B10 (TOD) and 37 (ECU)
•
B11 (TOD) and A24
•
B10 (TOD) and A23
•
B11 (TOD) and ground
•
B10 (TOD) and ground
Does the resistance of the all circuits measure within the
value specified?
Repair or replace any short wires, faulty connector, or
terminal.
Is the repair complete?
TRANSFER CASE - TOD 5D2-39
SSANGYONG Y200
Yes
System OK
System OK
No
Go to Step 6
-
Value
-
-
Step
5
6
Action
1. Replace the TOD.
2. Connect all connectors.
3. Request DTC with scan tool.
Is the repair complete?
Replace the ECU.
Is the repair complete?
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст