SsangYong Rexton. Service manual — part 648
RESTRAINTS 8B-15
SSANGYONG Y200
Check
Check the connection of the driver side airbag sensor connector.
Check the wiring condition of the driver side airbag sensor.
Check the bending of the airbag terminal.
Check the connection of the driver side airbag sensor connector.
Check the wiring condition of the driver side airbag sensor.
Check the bending of the airbag terminal.
Check the connection of the driver side airbag sensor connector.
Check the wiring condition of the driver side airbag sensor.
Check the bending of the airbag terminal.
Check the connection of the passenger side airbag sensor
connector.
Check the wiring condition of the passenger side airbag sensor.
Check the bending of the airbag terminal.
Check the connection of the passenger side airbag sensor
connector.
Check the wiring condition of the passenger side airbag sensor.
Check the bending of the airbag terminal.
Check the connection of the passenger side airbag sensor
connector.
Check the wiring condition of the passenger side airbag sensor.
Check the bending of the airbag terminal.
Check the connection of the passenger side airbag sensor
connector.
Check the wiring condition of the passenger side airbag sensor.
Check the bending of the airbag terminal.
Check generator output voltage.
Check the battery voltage.
Check the bending of the airbag terminal.
Check generator output voltage.
Check the battery voltage.
Check the bending of the airbag terminal.
Replace the SDM.
Replace the SDM.
Code
51h
52h
53h
54h
55h
56h
57h
17h
18h
1Eh
1Fh
Fault Contents
Passenger side airbag circuit,
short to ground
Communication malfunction of
the driver side airbag
Internal fault of the driver side
airbag sensor
Passenger side airbag sensor,
open/short to battery voltage
Passenger side airbag sensor,
short to ground
Communication malfunction of
the passenger side airbag
Internal fault of the passenger
side airbag sensor
Battery voltage too high
Battery voltage too low
SDM internal fault
(Initialization fault)
SDM internal fault
Caution:
•
Use only the scan tool to check the airbag
module and the sensing and diagnostic module
(SDM). Never measure the resistance of an airbag
module with an ohmmeter. An ohmmeter’s
battery can deploy the airbag and cause injury.
•
Before testing, disconnect the negative battery
cable. Wait 1 minute for the SDM capacitor to
discharge. The capacitor supplies reserve power
to deploy the airbags, even if the battery is
disconnected. Unintentional deployment of the
airbags can cause injury.
•
Do not attempt to repair the supplemental
inflatable restraints (SIR) wiring harness. An SIR
repair can create a high-resistance connection
which can keep the airbags from deploying when
needed, resulting in injury.
SSANGYONG Y200
8B-16 RESTRAINTS
ON-VEHICLE SERVICE
AIRBAG MODULE (DRIVER)
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Place the steering wheel at the straight driving
direction.
3. Remove the screw of the airbag module.
YAD8B110
YAD8B120
YAD8B130
4. Disconnect the airbag module connector, the horn
connector and then remove the airbag module.
5. Verify to tighten all of the module and each
connector.
Installation should follow the removal procedure
in the reverse order.
MAINTENANCE AND REPAIR
RESTRAINTS 8B-17
SSANGYONG Y200
2. Remove the upper and lower cover of the steering
column.
YAD8B150
YAD8B160
3. Disconnect the contact coil connector and remove
the contact coil mounting screw. Remove the
contact coil assembly.
CONTACT COIL
Removal and Installation Procedure
1. Remove the steering wheel, the lower panel at the
driver side.
YAD8B140
YAD8B170
4. Tighten the contact coil mounting screw as the
specified torque.
Installation should follow the removal procedure
in the reverse order.
Installation Notice
Tightening Torque
3 N•m (27 lb-in)
SSANGYONG Y200
8B-18 RESTRAINTS
;;;;
yyyy
5. Fix the contact coil to the center position.
Notice: If the clock spring is not properly aligned,
the steering wheel may not be able to rotate
completely during a turn. Restricted turning ability
can cause the vehicle to crash. Improper alignment
o f t h e c l o c k s p r i n g a l s o m a y m a k e t h e
supplemental inflatable restraints (SIR) system
inoperative, preventing the airbags from deploying
during a crash. Both of these outcomes can result
in injury.
Notice: Turn the label of the clock spring clockwise
to lock and turn the label of the clock spring
counterclockwise approximately 2.9 ¡¾ 0.2 turns
to the neutral positions with the front wheels ahead.
And also Align the pointed marks “
"!
” .
YAD8B180
YAD8B190
AIRBAG MODULE (PASSENGER)
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the glove box.
3. Disconnect the airbag module connector.
YAD8B200
4. Remove the airbag module.
5. Installation should follow the removal procedure
in the reverse order.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст