Jaguar X-Type Sedan and Estate (Wagon). Service manual — part 378
DTC
Description
Possible Cause
Action
P096900 Pressure Control
Solenoid C Control
Circuit
Range/Performance
High contact resistance in the
connector terminals between
TCM and transmission
open circuit of internal wiring
for SLC2 control signal circuit
open circuit of internal wiring
for SLC2 ground control signal
circuit
SLC2 pressure control solenoid
no operation
SLC2 pressure control solenoid
stuck
Internal failure in TCM
Check the terminals for corrosion, oxidation between TCM and
transmission. Suspect the TCM, check and install a new TCM as
required, refer to the new module/component installation note at the
top of the DTC Index. Suspect the transmission, check and install a
new transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system
P097000 Pressure Control
Solenoid C Control
Circuit Low
Short to ground of internal
wiring for SLC2 control signal
circuit
Open circuit of internal wiring
for SLC2 control signal circuit
SLC2 pressure control solenoid
no operation
Internal failure in TCM
Suspect the TCM, check and install a new TCM as required, refer to the
new module/component installation note at the top of the DTC Index.
Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system
P097100 Pressure Control
Solenoid C Control
Circuit High
Short to power of internal
wiring for SLC2 control signal
circuit
SLC2 pressure control solenoid
no operation
Internal failure in TCM
Suspect the TCM, check and install a new TCM as required, refer to the
new module/component installation note at the top of the DTC Index.
Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system
P097300 Shift Solenoid A
Control Circuit Low
Short to ground of internal
wiring for S1 shift solenoid 1
S1 shift solenoid 1 not
working
Internal failure in TCM
Suspect the TCM, check and install a new TCM as required, refer to the
new module/component installation note at the top of the DTC Index.
Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system
P097400 Shift Solenoid A
Control Circuit High
High contact resistance in the
connector terminals between
TCM and transmission
Open circuit of internal wiring
for S1 shift solenoid 1
S1 shift solenoid 1 not
working
Short to power of internal
wiring for S1 shift solenoid 1
Internal failure in TCM
Suspect the TCM, check and install a new TCM as required, refer to the
new module/component installation note at the top of the DTC Index.
Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system
P097600 Shift Solenoid B
Control Circuit Low
Short to ground of internal
wiring for S2 shift solenoid 2
S2 shift solenoid 2 not
working
Internal failure in TCM
Suspect the TCM, check and install a new TCM as required, refer to the
new module/component installation note at the top of the DTC Index.
Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system
P097700 Shift Solenoid B
Control Circuit High
High contact resistance in the
connector terminals between
TCM and transmission
Open circuit of internal wiring
for S2 shift solenoid 2
S2 shift solenoid 2 not
working
Short to power of internal
wiring for S2 shift solenoid 2
Internal failure in TCM
Suspect the TCM, check and install a new TCM as required, refer to the
new module/component installation note at the top of the DTC Index.
Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system
P171900 Engine Torque Signal
CAN message, engine torque
signal has not been updated
CAN message, engine torque
signal quality factor equals
zero
Check for ECM DTCs. Rectify as required
P173D00 Ignition Key Lock
Solenoid Circuit /
Open
Open circuit between ignition
switch keylock solenoid and
GSM
Carry out any diagnostic pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the electrical
guides and check for open circuit between ignition switch keylock
solenoid and GSM
P173E00 Ignition Key Lock
Solenoid Circuit Low
Short to ground between
ignition switch keylock
solenoid and GSM
Carry out any diagnostic pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the electrical
guides and check for short to ground between ignition switch keylock
solenoid and GSM
P173F00 Ignition Key Lock
Solenoid Circuit High
Short to power between
ignition switch keylock
solenoid and GSM
Carry out any diagnostic pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the electrical
guides and check for short to power between ignition switch keylock
solenoid and GSM
P178368 Transmission
Overtemperature
Condition
Event information. System
event not caused by the TCM,
but requiring the TCM to
record this DTC
Transmission fluid level low
Transmission fluid
cooler/hoses are
Check the transmission fluid level and condition, correct as required.
Check the transmission fluid cooler hoses for signs of
obstruction/damage/blockage, correct as required. Check the engine
cooling system and engine cooling fans operation. Suspect the
transmission, check and install a new transmission as required, refer
to the new module/component installation note at the top of the DTC
Index. Refer to service routines at the top of the DTC Index and carry
DTC
Description
Possible Cause
Action
obstructed/damaged/blocked
Mechanical failure of
transmission
Transmission has been
exposed to excessive high
load and high ambient
temperature greater than 150
degrees C (302 degrees F)
out service routines as required using the manufacturer approved
diagnostic system
P179900 CAN TCM/ABS Circuit
Malfunction
Vehicle speed message has
not been updated on CAN
ABS malfunction
Carry out any diagnostic pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Check ABS for DTCs
rectify as required
P215800 Vehicle Speed Sensor
B
Open circuit of internal wiring
NIN+ input speed sensor
circuit
Short circuit to ground of
internal wiring NIN+ input
speed sensor circuit
Input speed sensor failure
Internal failure in TCM
Check the terminals for corrosion, oxidation between TCM and
transmission. Check NIN+ circuit for open circuit, short to ground.
Replace Input speed sensor. Suspect the TCM, check and install a new
TCM as required, refer to the new module/component installation note
at the top of the DTC Index. Refer to service routines at the top of
the DTC Index and carry out service routines as required using the
manufacturer approved diagnostic system
P271900 Pressure Control
Solenoid D Control
Circuit
Range/Performance
High contact resistance in the
connector terminals between
TCM and transmission
SLC3 pressure control solenoid
stuck
open circuit of internal wiring
for SLC3 control signal circuit
open circuit of internal wiring
for SLC3 ground control signal
circuit
SLC3 pressure control solenoid
no operation
Internal failure in TCM
Check the terminals for corrosion, oxidation between TCM and
transmission. Suspect the TCM, check and install a new TCM as
required, refer to the new module/component installation note at the
top of the DTC Index. Suspect the transmission, check and install a
new transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system
P272000 Pressure Control
Solenoid D Control
Circuit Low
High contact resistance in the
connector terminals between
TCM and transmission
Short to ground of internal
wiring for SLC3 control signal
circuit
Open circuit of internal wiring
for SLC3 control signal circuit
SLC3 pressure control solenoid
no operation
Internal failure in TCM
Check the terminals for corrosion, oxidation between TCM and
transmission. Suspect the TCM, check and install a new TCM as
required, refer to the new module/component installation note at the
top of the DTC Index. Suspect the transmission, check and install a
new transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system
P272100 Pressure Control
Solenoid D Control
Circuit High
Short to power of internal
wiring for SLC3 control signal
circuit
SLC3 pressure control solenoid
no operation
Internal failure in TCM
Suspect the TCM, check and install a new TCM as required, refer to the
new module/component installation note at the top of the DTC Index.
Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system
P272800 Pressure Control
Solenoid E Control
Circuit
Range/Performance
High contact resistance in the
connector terminals between
TCM and transmission
Open circuit of internal wiring
for SLB1 control signal circuit
Open circuit of internal wiring
for SLB1 ground control signal
circuit
SLB1 pressure control solenoid
no operation
SLB1 pressure control solenoid
stuck
Internal failure in TCM
Check the terminals for corrosion, oxidation between TCM and
transmission. Suspect the TCM, check and install a new TCM as
required, refer to the new module/component installation note at the
top of the DTC Index. Suspect the transmission, check and install a
new transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system
P272900 Pressure Control
Solenoid E Control
Circuit Low
High contact resistance in the
connector terminals between
TCM and transmission
Open circuit of internal wiring
for SLB1 control signal circuit
Open circuit of internal wiring
for SLB1 ground control signal
circuit
SLB1 pressure control solenoid
no operation
Internal failure in TCM
Check the terminals for corrosion, oxidation between TCM and
transmission. Suspect the TCM, check and install a new TCM as
required, refer to the new module/component installation note at the
top of the DTC Index. Suspect the transmission, check and install a
new transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system
P273000 Pressure Control
Solenoid E Control
Circuit High
Short to power of internal
wiring for SLB1 control signal
circuit
SLB1 pressure control solenoid
no operation
Internal failure in TCM
Suspect the TCM, check and install a new TCM as required, refer to the
new module/component installation note at the top of the DTC Index.
Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system
DTC
Description
Possible Cause
Action
P273300 Pressure Control
Solenoid F Stuck On
SLC1 pressure control not
engaged in drive
Mechanical fault in the
transmission
Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system
P273700 Pressure Control
Solenoid F Control
Circuit
Range/Performance
High contact resistance in the
connector terminals between
TCM and transmission
Open circuit of internal wiring
for SLC1 control signal circuit
Open circuit of internal wiring
for SLC1 ground control signal
circuit
SLC1 pressure control solenoid
no operation
SLC1 pressure control solenoid
stuck
Internal failure in TCM
Check the terminals for corrosion, oxidation between TCM and
transmission. Suspect the TCM, check and install a new TCM as
required, refer to the new module/component installation note at the
top of the DTC Index. Suspect the transmission, check and install a
new transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system
P273800 Pressure Control
Solenoid F Control
Circuit Low
High contact resistance in the
connector terminals between
TCM and transmission
Open circuit of internal wiring
for SLC1 control signal circuit
Open circuit of internal wiring
for SLC1 ground control signal
circuit
SLC1 pressure control solenoid
no operation
Internal failure in TCM
Check the terminals for corrosion, oxidation between TCM and
transmission. Suspect the TCM, check and install a new TCM as
required, refer to the new module/component installation note at the
top of the DTC Index. Suspect the transmission, check and install a
new transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system
P273900 Pressure Control
Solenoid F Control
Circuit High
Short to power of internal
wiring for SLC1 control signal
circuit
SLC1 pressure control solenoid
no operation
Internal failure in TCM
Suspect the TCM, check and install a new TCM as required, refer to the
new module/component installation note at the top of the DTC Index.
Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system
P278368 Torque Converter
Temperature Too High
Event information. System
event not caused by the TCM,
but requiring the TCM to
record this DTC
Torque converter temperature
greater than 170 degrees C
(338 degrees F)
Check the transmission fluid level and condition. Check the
transmission fluid cooler/hoses for signs of obstruction, damage,
blockage. Suspect the transmission, check and install a new
transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system
P278768 Clutch Temperature
Too High
Event information. System
event not caused by the TCM,
but requiring the TCM to
record this DTC
Torque converter stalled
The transmission fluid
temperature is the same, or
greater than 120 degrees C
(248 degrees F) for longer
than 5 seconds
The transmission fluid
temperature is greater than
120 degrees C and lower than
150 degrees C (302 degrees F)
for longer than 4 seconds
The transmission fluid
temperature is greater than
150 degrees (302 degrees F)
for longer than 3 seconds
Internal failure in TCM
Check the transmission fluid level and condition. Check the
transmission fluid cooler/hoses for signs of obstruction, damage,
blockage. Suspect the transmission, check and install a new
transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system
P280000 Transmission Range
Sensor B Circuit
(PRNDL Input)
Incorrect adjustment of gear
position sensor
Internal failure in TCM
Check the gear selector lever is adjusted correctly. Suspect the TCM,
check and install a new TCM as required, refer to the new
module/component installation note at the top of the DTC Index.
Refer to service routines at the top of the DTC Index and carry out
service routines as required using the manufacturer approved
diagnostic system
P280100 Transmission Range
Sensor B Circuit
Range/Performance
Undefined range when drive
selected
Incorrect adjustment of gear
position sensor
Internal failure in TCM
Check the gear selector lever is adjusted correctly. Suspect the TCM,
GSM or transmission check and install a new TCM, GSM or
transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system
P280500 Transmission Range
Sensor A / B
Correlation
Incorrect adjustment of gear
position sensor
Internal failure in TCM
Check the gear selector lever is adjusted correctly. Suspect the TCM,
check and install a new TCM as required, refer to the new
module/component installation note at the top of the DTC Index.
Refer to service routines at the top of the DTC Index and carry out
service routines as required using the manufacturer approved
diagnostic system
U000100 High Speed CAN
Communication Bus
CAN bus open circuit
CAN bus short circuit to
ground
CAN bus short circuit to power
Internal fault in another
control module in the same
Carry out any diagnostic pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the electrical
guides and check CAN circuit for open circuit, short to ground, short to
power. Suspect the TCM, check and install a new TCM as required,
refer to the new module/component installation note at the top of the
DTC Index. Refer to service routines at the top of the DTC Index and
DTC
Description
Possible Cause
Action
part of the CAN network
Internal failure in TCM
carry out service routines as required using the manufacturer approved
diagnostic system
U210511 Switch Pack Signal "A"
Circuit short to ground. The
TCM has detected a ground
measurement for a period
longer than expected or has
detected a ground
measurement when another
value was expected
Shiftlock solenoid circuit short
to ground
GSM internal failure
Refer to the electrical guides and check shiftlock circuit for short to
ground. Suspect the GSM, check and install a new GSM as required,
refer to the new module/component installation note at the top of the
DTC Index
U210512 Switch Pack Signal "A"
Circuit short to power. The
TCM has detected a vehicle
power measurement for a
period longer than expected or
has detected a vehicle power
measurement when another
value was expected
Shiftlock solenoid circuit short
to power
Open circuit shiftlock solenoid
circuit
GSM internal failure
Refer to the electrical guides and check shiftlock circuit for short to
power, open circuit. Suspect the GSM, check and install a new GSM as
required, refer to the new module/component installation note at the
top of the DTC Index
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст