Jaguar X-Type Sedan and Estate (Wagon). Service manual — part 545
Published: 11-May-2011
Exterior Lighting - Exterior Lighting
Description and Operation
The headlamp switch is located on the driver side of the instrument panel. It also operates the sidelamps, fog lamps, "Auto Mode",
headlamp levelling and the trip switch.
Each headlamp assembly consists of two lamps. The side lamp and the high beam lamp are the inner and the low beam and turn signal
lamp are the outer. Access for bulb replacement is from the engine compartment.
High intensity discharge (HID) lighting is fitted as an option.
WARNING: Voltages of up to 25 KV are possible with HID lighting.
Burner wear for HID lamps is so low that the burner lasts the lifetime of the vehicle under normal use. The HID bulbs are dealer replaceable
only.
• NOTE: After replacement of a sensor or module the HID lamps will need to be calibrated using a Jaguar Approved Diagnostic System.
The front fog lamps are located in recesses in the front bumper. The two retaining screws are located behind the splitter vane and are
accessible after removing the radiator splash shield.
The license plate lamp bulbs on all vehicles can be accessed by releasing the retaining tangs on the side of the lamps.
Each rear lamp assembly incorporates a stop/tail lamp, a fog lamp, a reversing lamp and a turn signal lamp. Access for bulb replacement is
from the luggage compartment.
The high mounted stop lamps for both 4-door vehicles and wagon are replaceable as units. On 4-door vehicles, the two retaining screws are
located behind the headliner and are accessible after the headliner has been removed. On wagon, the three retaining screws are located
below the tailgate spoiler, and are accessible after the tailgate spoiler has been removed.
On vehicles up to 2009MY, the side repeater lamps are located in the front fender. On vehicles from 2009MY, the side repeater lamps are
located in the door mirrors.
The side marker lamps on 4-door vehicles are located in the front bumper and rear bumper cover. These are located in each bumper cover by
tangs on one side of the unit and held in position by a spring clip on the other side. The rear side marker lamps on wagon are incorporated
in to each rear lamp assembly.
Published: 11-May-2011
Exterior Lighting - Headlamps
Diagnosis and Testing
Principle of Operation
For a detailed description of the lighting system, refer to the relevant Description and Operation sections in the workshop manual. REFER
to:
Exterior Lighting
(417-01 Exterior Lighting, Description and Operation).
Inspection and Verification
1. Verify the customer concern.
1.
2. Visually inspect for obvious signs of mechanical or electrical damage.
2.
Visual Inspection Chart
Mechanical
Electrical
Switch
Headlamp levelling motor
Levelling sensors
Relay(s)
W iring harness for damage or corrosion
Electrical connector(s)
Bulb(s)
Fuse(s)
Control module
3. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next
step.
3.
4. If the cause is not visually evident, verify the symptom and refer to the Jaguar Approved Diagnostic System.
4.
DTC Index
WARNING: Voltages of up to 25 KV are possible with HID lighting
• CAUTIONS:
Observe all recommended safety precautions relating to the operation and repair of headlamp systems. Refer to health and safety
guidance in the owner guide and repair manual for further details.
W hen probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00
• NOTE: If the control module/component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and
Procedures manual (section B1.2), or determine if any prior approval program is in operation, prior to the installation of a new
module/component.
• NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the DMM leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic routines that involve pinpoint tests.
• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause.
Always check for loose connections and corroded terminals.
DTC
Description
Possible Cause
Action
B1318 Battery voltage low
Charging system
fault
W iring harness
concern
Battery voltage low, check charging system for faults. Charge level is
controlled by engine control module.
B1342 ECU is faulted
Auto levelling ECU
internal error
Detectable internal defect (RAM/EEPROM error), check module for external
connection problems, replace module as required.
B2477 Module configuration
failure
Control module not
configured
Configure control module using manufacturer approved diagnostic system
B2608 ECU output to left
headlamp stepper motor
short to ground
W iring harness
concern
Refer to electrical circuit diagrams, check left headlamp stepper motor circuit
for short to ground. Repair wiring harness using approved methods and
materials. Clear DTC and retest system to ensure correct operation.
B2609 ECU output to left
headlamp stepper motor
circuit failure
W iring harness
concern
Refer to electrical circuit diagrams, check left headlamp stepper motor circuit
open circuit or short to power. Repair wiring harness using approved methods
and materials. Clear DTC and retest system to ensure correct operation.
B2610 ECU output driver to left
headlamp stepper motor
overtemperature
Headlamp fault
Check headlamp unit for blocking of stepper motor movement, or continuous
operation. Replace headlamp components as required. Clear DTC and retest
system to ensure correct operation
B2611 ECU output to right
headlamp stepper motor
short to ground
W iring harness
concern
Refer to electrical circuit diagrams, check right headlamp stepper motor circuit
for short to ground. Repair wiring harness using approved methods and
materials. Clear DTC and retest system to ensure correct operation.
B2612 ECU output to right
headlamp stepper motor
circuit failure
W iring harness
concern
Refer to electrical circuit diagrams, check left headlamp stepper motor circuit
open circuit or short to power. Repair wiring harness using approved methods
and materials. Clear DTC and retest system to ensure correct operation.
B2613 ECU output driver to right
headlamp stepper motor
overtemperature
Headlamp fault
Check headlamp unit for blocking of stepper motor movement, or continuous
operation. Replace headlamp components as required. Clear DTC and retest
system to ensure correct operation
B2614 Front or rear axle vehicle
level sensor supply short
to ground
W iring harness
concern
Refer to electrical circuit diagrams, check level sensor power supply circuit for
short to ground. Repair wiring harness using approved methods and materials.
Clear DTC and retest system to ensure correct operation.
DTC
Description
Possible Cause
Action
B2615 Front or rear axle vehicle
level sensor supply circuit
failure
W iring harness
concern
Refer to electrical circuit diagrams, check level sensor power supply circuit for
short to power. Repair wiring harness using approved methods and materials.
Clear DTC and retest system to ensure correct operation.
B2616 Front axle vehicle level
sensor signal circuit failure
W iring harness
concern
Refer to electrical circuit diagrams, check level sensor signal circuit for open
circuit, short to 5 volts, short to battery power. Repair wiring harness using
approved methods and materials. Clear DTC and retest system to ensure
correct operation.
B2617 Front axle vehicle level
sensor signal short to
ground
W iring harness
concern
Refer to electrical circuit diagrams, check front level sensor signal circuit for
short to ground. Repair wiring harness using approved methods and materials.
Clear DTC and retest system to ensure correct operation.
B2618 Front axle vehicle level
sensor signal not plausible
Sensor
fault/adjustment
wiring harness
concern
Front sensor signal out of range. Check lever position and adjustment of
sensor. Replace sensor if signal cannot be brought into range. Refer to
electrical circuit diagrams, check level sensor signal circuit for faults. Repair
wiring harness using approved methods and materials. Clear DTC and retest
system to ensure correct operation.
B2619 Rear axle vehicle level
sensor signal circuit failure
W iring harness
concern
Refer to electrical circuit diagrams, check level sensor signal circuit for open
circuit, short to 5 volts, short to battery power. Repair wiring harness using
approved methods and materials. Clear DTC and retest system to ensure
correct operation.
B2620 Rear axle vehicle level
sensor signal short to
ground
W iring harness
concern
Refer to electrical circuit diagrams, check rear level sensor signal circuit for
short to ground. Repair wiring harness using approved methods and materials.
Clear DTC and retest system to ensure correct operation.
B2621 Rear axle vehicle level
sensor signal not plausible
Sensor
fault/adjustment
wiring harness
concern
Rear sensor signal out of range. Check lever position and adjustment of
sensor. Replace sensor if signal cannot be brought into range. Refer to
electrical circuit diagrams, check level sensor signal circuit for faults. Repair
wiring harness using approved methods and materials. Clear DTC and retest
system to ensure correct operation.
B2622 Auto levelling ECU speed
message invalid / not
available
CAN message invalid
or not available
wiring harness
concern
Refer to electrical circuit diagrams, check CAN circuits for faults. Repair wiring
harness using approved methods and materials. Clear DTC and retest system
to ensure correct operation.
B2623 Auto levelling ECU low
beam message invalid /
not available
CAN message invalid
or not available
wiring harness
concern
Refer to electrical circuit diagrams, check CAN circuits for faults. Repair wiring
harness using approved methods and materials. Clear DTC and retest system
to ensure correct operation.
B2624 Auto levelling ECU speed
signal not available
speed signal circuit
malfunction
wiring harness
concern
Refer to electrical circuit diagrams, check CAN circuits for faults. Repair wiring
harness using approved methods and materials. Clear DTC and retest system
to ensure correct operation.
B2625 Auto levelling ECU low
beam signal input open
circuit
W iring harness
concern
Refer to electrical circuit diagrams, check ECU low beam input circuits for open
circuits. Repair wiring harness using approved methods and materials. Clear
DTC and retest system to ensure correct operation.
B2626 Auto levelling ECU not
calibrated
ECU not calibrated
or adjusted
Calibrate and adjust the headlamp levelling ECU using the manufacturer
approved diagnostic system. Clear DTC and retest system to confirm correct
operation
Published: 11-May-2011
Exterior Lighting - Headlamp Adjustment
General Procedures
1. NOTE: Headlamp adjustment should be made at room temperature.
Prepare the vehicle for headlamp adjustment.
1. Place the vehicle on a level surface.
2. Before adjusting the headlamps, check for faulty lenses,
reflectors and blackened bulbs. Install new components as
necessary.
3. Check the tire pressures and correct as necessary. For
additional information, refer to Section
204-04 Wheels and
Tires
.
4. The vehicle must be at normal weight.
5. Normalize the suspension.
2. Rotate the headlamp adjustment switch to the 'O' position.
3. Adjust the headlamp using the adjustment bolts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст