Jaguar X-Type Sedan and Estate (Wagon). Service manual — part 69
Published: 11-May-2011
Front Disc Brake -
Lubricants, Fluids, Sealers and Adhesives
CAUTION: Do not use brake fluid ITT Super Dot 4 on 2006my vehicles onwards. Failure to follow this instruction may result in damage
to the vehicle.
• NOTE: Brake fluid ITT Super Dot 4 has now been superseded by Shell ESL Super Dot 4 which is the Jaguar recommended brake fluid. Shell
ESL Super Dot 4 can be used on all model years.
Item
Specification
Brake fluid
ITT Super Dot 4
Brake fluid
Shell ESL Super Dot 4
Brake caliper slide pin grease
Klueber GLK1
Torque Specifications
Description
Nm
lb-ft
lb-in
Brake pipe union
15
11
-
Brake caliper anchor plate retaining bolts
133
98
-
Brake caliper retaining bolts
30
22
-
Brake hose retaining bracket
40
30
-
Brake hose to brake caliper
10
7
-
Published: 11-May-2011
Front Disc Brake - Front Disc Brake
Description and Operation
Item
Part Number
Description
1
—
Brake hose
2
—
Brake caliper retaining bolts
3
—
Brake pads
4
—
Brake caliper anchor plate
5
—
Brake disc
6
—
W heel hub
7
—
W heel knuckle
8
—
Brake hose retaining bracket
9
—
Brake caliper
WARNING: Brake fluid contains polyglycol ethers and polyglycols. Avoid contact with the eyes. W ash hands thoroughly after handling.
If brake fluid contacts the eyes, flush the eyes for 15 minutes with cold running water. Get medical attention if irritation persists. If taken
internally, drink water and induce vomiting. Get medical attention immediately. Failure to follow these instructions can result in personal
injury.
• NOTE: Brake system materials inherently generate heat in order to dissipate energy. As a result, occasional squeal is possible, which may
be compounded by severe environmental conditions, such as cold, heat, rain, snow, salt and mud.
The front disc brake system consists of the following components:
Brake pads.
Single piston, floating brake calipers.
Brake discs.
Brake caliper anchor plates.
Brake hoses.
The brake caliper has two retaining bolts that attach it to the brake caliper anchor plate. The brake caliper anchor plate is attached to the
wheel knuckle with two retaining bolts. The hydraulic system provides separate circuits for each pair of diagonally opposed wheels (i.e. left
front, right rear and right front, left rear).
The brake disc is manufactured from cast iron and is of the vented type. It is retained on the wheel hub studs by the wheel and wheel nuts.
The brake calipers are mounted on the wheel knuckles. These are of single, sliding piston type which ensures that equal effort is applied
through both brake pads.
Published: 11-May-2011
Front Disc Brake - Front Disc Brake
Diagnosis and Testing
For additional information, refer toSection
206-00 Brake System - General Information
.
Published: 11-May-2011
Front Disc Brake - Brake Caliper
Removal and Installation
Special Tool(s)
Brake pedal hold-down tool
JDS 9013
Removal
1. Remove the wheel and tire. For additional information, refer toSection
204-04 W heels and Tires
.
2.
CAUTION: If brake fluid is spilt on the paintwork, the affected
area must be immediately washed down with cold water.
• NOTE: To prevent the loss of brake fluid, apply the brake pedal hold
down tool and adjust to hold the brake pedal down 40mm. Install a
bleeder bottle to the bleed nipple and loosen.
Detach the brake hose.
1. Detach the brake pipe.
2. Remove the retaining clip.
3. Detach the brake hose.
3. Detach the brake hose.
4. NOTE: Tighten the bleed nipple and remove the bleeder tube and
bottle.
Remove the brake caliper.
Remove and discard the brake caliper retaining bolts.
Installation
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст