Jaguar XJ (X350). Service manual — part 367
303-01B : Engine – 3.5L/4.2L
Specifications
Specifications
Lubricants, Fluids, Sealers and Adhesives
Description
Specification
Engine oil, SAE 5W-30
WSS-M2C-912A
Engine assembly lubricant SQM-2C9003 AA EP90
Sealant
WSS M4G 320-A3
Hose assembly surfactant ESE-M99 B144-B
Capacities
Description
Liters
Engine oil, initial fill
6.8
Engine oil, service fill with oil filter change 6.5
Cylinder Head
Item
Specification
Maximum permitted cylinder head warp (mm) 0.125
Torque Specifications
Description
Nm
lb-ft
lb-
in
Accessory drive belt idler pulley retaining bolt
25
18
-
Accessory drivebelt tensioner retaining bolt
40
30
-
Air conditioning compressor retaining bolts
25
18
-
Air conditioning compressor mounting bracket
retaining bolts
25
18
-
A/C manifold retaining bolt
20
15
-
Camshaft bearing caps retaining bolts
10
7
-
Camshaft position sensor retaining bolt
7
-
62
Connecting rod retaining bolts
A
-
-
Crankshaft pulley retaining bolt
377
278
-
Crankshaft position sensor retaining bolt
10
7
-
Cylinder head retaining bolts
A
-
-
Drive plate retaining bolts
A
-
-
Engine front cover retaining bolts
13
10
-
Engine mounting bracket retaining bolts
40 (+/- 15%)
30 (+/- 15%)
-
Engine mount retaining nuts to crossmember
55 (+/- 15%)
40 (+/- 15%)
-
Engine mount bracket to engine mount retaining nuts 63 (+/- 15%)
46 (+/- 15%)
-
Engine wiring harness retaining bracket
10
7
-
Exhaust manifold heat shield retaining bolts
3
-
27
Exhaust manifold heat shield retaining bolt to cylinder
head
50
37
-
Exhaust manifold retaining bolts
20
15
-
Flexiplate retaining bolts
A
-
-
Front engine cover retaining bolts
12
9
-
Generator lower retaining bolt
40
30
-
Generator upper retaining bolt
21
15
-
Generator lower retaining bolt
40
30
-
Generator mounting bracket retaining bolts
45
33
-
Ignition coil retaining bolts
5
4
-
Intake manifold assembly retaining bolts
22
16
-
Intake camshaft sprocket retaining bolt
Stage 1
20
15
-
Stage 2
Further 90
degrees
Further 90
degrees
-
Knock sensor retaining nuts
20
15
-
Lower cylinder block to the upper cylinder block
retaining bolts
A
-
-
Oil cooler to oil filter housing retaining bolt
20
15
-
Oil filter housing retaining bolts
21
15
-
Oil level indicator tube retaining nut
6
-
51
Oil pan retaining bolts
12
9
-
Oil pump to engine block retaining bolts
12
9
-
Oil pan drain plug
25
18
-
Oil separator retaining bolts
12
9
-
Oil filter
18
13
-
Piston cooling jet retaining bolt
9
-
80
www.
Power steering bracket bracket retaining bolts
25
18
-
Power steering pump retaining bolts
25
18
-
Primary timing chain tensioner retaining bolts
12
9
-
Primary timing chain tensioner guide retaining bolts
12
9
-
Secondary timing chain tensioner retaining bolts
12
9
-
Spark plugs
27
20
-
Starter motor retaining bolts
45
33
-
Thermostat housing retaining bolts
10
7
-
Water pump retaining bolts
12
9
-
Water pump pulley retaining bolts
A
-
-
Upper oil pan retaining bolts
21
15
-
Valve cover retaining bolts
10
7
-
Variable camshaft timing (VCT) oil control unit
housing retaining bolts
22
16
-
VCT sprocket centre retaining bolt
Stage 1
20
15
-
Stage 2
Further 90
degrees
Further 90
degrees
-
A = refer to the procedure for the correct torque
sequence
-
-
-
General procedures
Valve Clearance Adjustment (12.29.48)
Special Service Tools
Tappet hold down tool
303-540
Fan nozzle, air gun
303-590
1. Remove the left-hand valve cover.
2. Remove the right-hand valve cover.
3. Use a cloth to wipe away as much oil as possible from the tappet and shim.
4.
CAUTION: Rotating the crankshaft in a counterclockwise direction may cause engine
damage. Crankshaft journals are directionally machined. Rotating the crankshaft counterclockwise
can raise burrs on bearing surfaces, reducing engine life.
CAUTION: Camshaft lobes must be 180 degrees away from each valve tappet or the valve
clearance will be incorrect.
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст