JAC S7. Instruction — part 5

-17

Power steering fluid

When to check the power steering fluid
The power steering stock solution tank
is in the front of the engine cabin beside
the vehicle passengers. See 野General
Drawing of Engine Cabin冶 in this section
to confirm the position of the stock solu鄄
tion tank.
Unless you doubt that there is leakage
in the system or you have heard abnor鄄
mal sound, it is unnecessary to inspect
the power steering fluid. The run away
of the power steering fluid shows that
there is failure, and it is required to
check and repair the system.

How to inspect the power steering fluid?
Inspect the power steering fluid as the
following steps:
1. Cut off the ignition switch and wait
the engine cabin to be cool.
2. Wipe clean the tank cover and the
surface of the stock solution tank.
3. Unscrew the tank cover.
4. Add power steering fluid to the prop鄄
er level.
Mount the tank cover again and screw
tightly completely.

The level shall be between the upper
limit MAX mark and lower limit of the
stock solution tank.
If the level falls to or below the lower
limit MIN mark position, add power
steering fluid to make the level rise to
the upper limit MAX position.

MO TORS

You can remove the coolant expansion
pot cover after the cooling system, in鄄
cluding coolant expansion pot cover
and radiator hose, cools down.
Add proper mixture to the coolant ex鄄
pansion pot till it reaches the upper limit
mark of the expansion pot. Wait for 5
minutes, and check whether the fluid
level is lower than the upper limit mark.
If the fluid level is lower than the upper
limit mark, raise the level to the upper

limit position by adding some coolant
again. Repeat this step to keep the level
at the upper limit position for at least 5
minutes.
Do not cover the expansion pot cover
and start the engine to let it run until you
can feel the upper radiator hose be鄄
come hot. Be careful not to touch the
cooling fan. At this time, the coolant lev鄄
el in the expansion pot will fall; add
more mixture to the expansion pot to
make the level reach the upper limit
mark position if the level is lower than
the upper limit mark. Then cover the
cover and make sure the cover is
mounted in place.

Main fluid parameters
It is suggested to use the following
coolant specification.

Notes

When the weather is cold, the water will
cause the engine, radiator and other
components to become frost cleft. So,
please use the recommended coolant
and proper coolant mixture.

-16

Name

Brand

Volume

Engine
coolant

43/57 proportioned anti -
freezing solution at -45益

7L

-19

Brake fluid

What is added to the brake master
cylinder stock solution tank is DOT4
brake fluid.
There two reasons for the falling of the
brake fluid level in the stock solution
tank. One is that the brake fluid falls to
the acceptable level position in the nor鄄
mal wear process of the braker friction
gasket. And the level can recover to the
normal position after replacing new fric鄄
tion gasket.
Another reason is that the brake fluid is
leaking outwards from the brake system.
If it is for this reason, you should repair
the brake system. Because leakage
means that the brake will not work nor鄄
mally or can not work sooner or later.

So, it is useless to add brake fluid when
the level falls. Add brake fluid can not
change the leakage. What爷s more, if
you add brake fluid when the friction
gasket wears out, the brake fluid will be
too much after replacing the old friction
gasket. Only when the repair work of the
brake hydraulic system has been fin鄄
ished, can add or reduce the brake fluid
as required.

If the brake fluid level is low, the brake
warning lamp will light on; see 野Warning
Lamp for Brake System冶 in section III.

Notes

If the brake fluid is too much, it will
splash onto the engine. If the tempera鄄
ture of the engine is high enough to
burn the brake fluid and to burn you or
others, and it will cause damage to the
vehicle. So, only when the repair work
of the brake hydraulic system has been
finished, can add brake fluid.

MO TORS

Water will freeze the solution, and the
solution freezing will cause damage to
the front windscreen washer system.
The radiator anti-freezing solution may
also cause damage to the front wind鄄
screen washer system and the vehicle
paint.

Notes

Adding front windscreen washing solu鄄
tion tank:
Do use special washing solution sold in
the market.
Prohibit using tap water, because the
mineral substances will block the pipe
of the front windscreen washer.
If the temperature may reduce to ice
point, do use the front windscreen
washing solution with enough anti -
freezing performance.
Prohibit adding water or radiator anti -
freezing solution to the front windscreen
washer solution tank.

Front windscreen washing solution

Before driving, make sure that the level
of front windscreen washing solution is
suitable and add proper solution as the
regulation of this instruction.
Under the condition of cold weather,
prohibit adding front windscreen wash鄄
ing solution to more than one fourth.
The washing solution will freeze and ex鄄

pand at low temperature. If add too
much, the washing solution will loss the
expansion space and it may cause
damage to the solution tank.

-18

-21

Notes

There is lead, lead compound and oth鄄
er chemical compounds in the ends,
binding post and the relative acces鄄
sories. So wash hands after touching it.

Storage battery

There is maintenance free storage bat鄄
tery installed in your vehicle. If you want
to replace the storage battery, the part
number on volume of all the storage
battery shall be the same with that of
the original storage battery. See 野Gen鄄
eral Drawing of Engine Cabin冶 in this
section to confirm the position of the
storage battery.

Vehicle storage
If the vehicle will not run in at least three
weeks, the cathode cable of the storage
battery should be cut off, which will pre鄄
vent the storage battery from leakage.

Clear up binding post of storage battery
1. Shut off the ignition switch and draw
out the key.
2. Loosen and disassemble the cable
clip of the storage battery from the
binding post with spanner. Do cut off
the cathode binding post (要) of the
storage battery first.
3. Clear up the binding post with steel
wire brush and clearing tool for binding
post.
4. Check if there is white or light blue
powder on the binding post of the stor鄄
age battery. If there is, it shows the
binding post has been eroded.
5. Clear up the eroded substances with
water solution of sodium bicarbonate.
The water solution of sodium bicarbon鄄
ate will make bubbles and become

Notes

The acid liquor in the storage battery
will burn you, and the generated gas is
explosive. If you are not careful, you will
be seriously injured. See 野Jumper
Start冶 in this section to know of the re鄄
lated hints for avoiding damage when
working around the storage battery.

MO TORS

淫 It will cause damage to the vehicle
paint if the brake fluid splashes onto
the vehicle paint surface. So pay at鄄
tention not to splash the brake fluid on鄄
to the vehicle. If it does, clean it im鄄
mediately. See 野Appearance Curing冶
in this section.

Which kind of brake fluid to be added?

When it is required to add brake fluid,
you can only use JG4 brake fluid and
can only use new brake fluid in un鄄
opened container. See 野Main Fluid Pa鄄
rameters冶 in section II.
Before unscrew the stock solution tank
cover for brake fluid, you should clean
the tank cover and the components
around it. It can prevent the dirt from

going to the stock solution tank by do鄄
ing this.

Notes

If the type of brake fluid which is
added to the brake system is not cor鄄
rect, the brake can not work normally.
And it will cause accident. So, do use
the correct type of brake fluid.
淫 Using wrong type of brake fluid
will cause serious damage to the com鄄
ponents of brake system. For example,
adding only a few drops of mineral oil
to the brake system will cause serious
damage to the components of brake
system, and you have to replace these
components. Therefore, you should
prevent anyone to add the wrong type
of brake fluid.

-20

Fuse box of engine cabin

-23

MO TORS

brown.
6. When it stops making bubbles, flush
the solution with clean water, then wipe
the storage battery with paper and
cloth.
7. Connect and tighten the anode (+ )
binding post again and then connect
the cathode (要) binding post again.

Maintenance of storage battery
When maintaining and assembling stor鄄
age battery, do carry and place it gen鄄
tly. And avoid the electrolyte from leak鄄
age or exploding or generating safety
accident. Check if there is electricity
before assembling the storage battery.
If the electricity indicator on the storage
battery shows dark blue, it means the
electricity in the storage battery is full; if
shows light blue or transparent color, it
means there is leakage in the storage
battery, and it needs charge.
In order to prolong the lifespan of the
vehicle storage battery, the following
way should be obeyed.
淫 Keep the proof of storage battery
clean and dry.

淫 Keep the binding post and post
head clean tightened and smear vase鄄
line or lubricating grease on it.
淫 Immediately flush the splashed el-
ectrolyte with water solution of sodium
bicarbonate.
淫 If you do not use your vehicle for a
long time, cut off the cathode (要) bind鄄
ing post of the storage battery and
charge the storage battery one every 6
weeks.

Notes

The storage battery contains poisonous
substances, and the used storage bat鄄
tery is bad for health and environment.
Prohibit treating the used battery with
household garbage. Do use the local
legal automobile waste disposal facility.

-22

Notes

淫 Prohibit disassembling the broken
fuse with electric tool. Do use the fuse
remover.
Using the electric material, such as
metal, will cause short circuit and break
the electric system or get fire. And it
may cause damage to people.

Fuse

Replacing fuse:
1. Open the fuse cover.
2. Judge the damaged fuse by burnt
fuse.
3. Remove the broken fuse with fuse re鄄
mover.

4. Confirm the reasons of causing the
fuse to break and eliminate the failure.
5. Install new fuse with the rating current
conforming to the regulation of this man鄄
ual.

Attentive hint

There are four spare fuses (10A, 15A,
20A, and 30A) in the fuse and relay box
of the engine room.

Notes

Using fuse substitute or the fuse with
wrong type and rating value will cause
damage to the electric system or get
fire.
淫 Do use the fuse with the type and
rating current conforming to this manu鄄
al.
Otherwise, it will cause damage to
people and to vehicle or other property.

-25

MO TORS

F20-reserved
F21-reserved
F22-reserved
F23-reserved
F24-anti-theft alarm insurance
F25-front fog lamp insurance
F26-ACC insurance
F27-instrument insurance
F28-BCM IG insurance
F29-windscreen wiper insurance
F30-IG2 insurance
F31-ABS insurance
F32-danger alarm insurance
F33-reversing lamp insurance
F34-indoor lamp insurance

F35-diagnosis insurance
F36-reserved
F37-reserved
F38-reserved
F39-reserved
F40-reserved
F41-seat heating insurance
F42-insurance of radio with cassette
player
F43-AM insurance
F44-insurance of start relay coil
F45-turn light insurance
F46-stop lamp insurance
F47-horn insurance
F48-airbags insurance

F49 -electric rear mirror heating in鄄
surance
F50-small lamp insurance
F51-reserved
R/L10-on relay
R/L11-reserved
R/L12-blower relay 1
R/L13-blower relay 2
R/L14-rear defrost relay
R/L15-front fog relay
R/L16-anti-theft relay
R/L17-small light relay
R/L18-horn relay
R/L19-cigarette light relay
R/L20-light flash relay

-24

F1-main insurance
F2-IG fuse buffer
F3-30 fuse buffer
F4-start fuse buffer
F5-electric fan insurance 1
F6- electric fan insurance 2
F7-electric window insurance 1
F8- electric window insurance 2
F9 -central controlling lock insur鄄
ance

F10-cigarette lighter insurance
F11-rear defrost /rear mirror heat鄄
ing insurance
F12-EFI main relay insurance
F13-high beam light insurance
F14-dipped headlight insurance
F15-fuel pump insurance
F16-30 fuse buffer 2
F17-30 fuse buffer 3
F18-blower insurance

F19-EFI B+ insurance
R/L1-oil pump relay
R/L2-main relay of engine
R/L3-compressor relay
R/L4-high beam relay
R/L5-condensing fan relay
R/L6-radiator fan relay 2
R/L7- high beam relay
R/L8-fan controlling relay
R/L9-start protective relay

-27

MO TORS

Cab fuse box

-26

Lamp

Headlamp

Front fog lamp

Front fog lamp

Side turn light

Headlamp

Turn light

Dipped headlight

High beam light,

Front positioning light

Rear combination light

Stop lamp, Rear

positioning lamp

Reversing lamp,

Turn light

Rear fog lamp

License light

Rear combination light

Arrangement plan of outer vehicle lamps

-29

MO TORS

Notes

Using fuse substitute or the fuse with
wrong type and rating value will cause
damage to the electric system or get
fire.
Do use the fuse with the type and rat鄄
ing current conforming to this instruction.
Otherwise, it will cause damage to
people and to vehicle or other property.

Replacing fuse:

1. Disassemble storage box at the driv鄄
er爷s side.
2. Judge the damaged fuse by burnt
fuse.
3. Remove the broken fuse with fuse re鄄
mover.

4. Confirm the reasons of causing the
fuse to break and eliminate the failure.
5. Install new fuse with the rating current
conforming to the regulation of this man鄄
ual.

Notes

Prohibit disassembling the broken fuse
with electric tool. Do use the fuse re鄄
mover.
Using the electric material, such as
metal, will cause short circuit and break
the electric system or get fire. And it
may cause damage to people.

-28

Collocation name

Functions and structure type

Front indoor (ceiling ) light

Reading lamp, with eye box and sun roof switch

Rear indoor (ceiling ) light

Reading lamp with door control function

Four door lamps

Bulb and lamp shade are installed separately.

Rear boot lamp

Cylindrical bulb

Grocery room lamp

Cylindrical bulb

Left and right feet illumination lamp

Cylindrical bulb

Inner illumination device type

-31

MO TORS

Lamp name

Functions and structure type

Front combination light

High beam light, dipped headlight, Front positioning light, Turn light.
Combined four-lamp headlamp
Projecting mirror is adopted with glass lens of dipped headlight.

Front fog lamp

Mounted on the front bumper.

Side steering lamp

Mounted on the flank board

Rear combination light

Including rear positioning lamp, stop lamp, turn light, reversing lamp, rear fog lamp.
Combine rear light
The color of glass lens is mainly double colors.
Brake lamp and position lamp share the same luminous surface.

High position stop lamp Using LED light source
License lamp

Common structure

Outer illumination and signal device type

-30

Notes

The engine may start unexpectedly if
the key is not turned out.
Prohibit keeping the key in the ignition
switch when inspecting the transmis鄄
sion belt.
When the engine is working, it may be
caused serious accident injury if mov鄄
ing the components.

Transmission belt

Transmission belt must be in good con鄄
dition and adjusted in place, so that the
generator can work normally. Replace
the transmission belts which are worn,
cracked and broken.

Inspecting the belt

Inspecting the rate of tension of the
transmission belt:
1. Slightly press the middle of the
longest unsupported length of the
transmission belt with thumb. The pres鄄
sure of the thumb is about 10kg.
2. Press the transmission belt with
thumb, which produce the deflection of
about 10mm.

3. If the belt is too loose, it should be
adjusted by Special After -sale Service
Center of Jianghuai Automobile Co.,
Ltd.

-33

MO TORS

No.

Name

Parameter requirements

Power

1

Front combination light

High beam light

Tungsten halide lamp H1

55W

Dipped headlight

Shooting lamp: Tungsten halide lamp H7

55W

Position light

Filament lamp

5W

Turn light

Filament lamp

21W

2

Rear combination light

Turn light

Filament lamp

21W

Stop light

LED

3W

Reversing lamp

Filament lamp

21W

Rear fog lamp

Filament lamp

21W

Position lamp

LED

3W

Reverting reflector lamp The installing height is according to International Standards.

3

Front fog lamp

Tungsten halide lamp

55W

4

Side steering lamp

Filament lamp

5W

5

High position stop lamp

LED

3W

6

License lamp

Filament lamp

5W

7

Front ceiling light assembly

Incandescent bulb, integrated sun roof control switch

5W伊2

8

Rear ceiling light assembly

Incandescent bulb, control, see inner schematic diagram

5W伊2

9

Indoor small lamp assembly

Filament lamp

5W

10

Door light

Filament lamp

5W

-32

If the tyre inflation is excessive, it will
cause:
淫 Abnormal abrasion
淫 Bad maneuverability
淫 Bad riding comfort
淫 Unnecessary damage because of
bad road

The tyre and weight information scrolling
are fixed on the side of the vehicle door
of the driver. The tag indicates the prop鄄
er inflation pressure when the tyre is in
cold condition, and the proposed infla鄄
tion pressure indicated on the tags for
the tyre in cold condition is the minimum
tyre pressure required for supporting
the maximum vehicle capacity.
When to inspect the tyre pressure
Inspect the tyre pressure at least once
per month.

How to inspect the tyre pressure
Inspect the tyre pressure with pocket鄄
sized tyre gauge of good quality. It can
not be determined whether the tyre
pressure is suitable only by visual in鄄
spection. The braced -tread tyre looks
normal even if the inflation is insufficient.
Inspect the inflation pressure of the tyre
when it is in cold condition. The tyre in
cold condition refers to the tyre works
within 3 hours or not more than 1.6km.
Remove the valve cock from the valve
pin of the tyre, press the tyre gauge on
the valve and then measure the pres鄄
sure number. If the inflation pressure of
the tyre in cold condition conforms to
the proposed pressure value of the tyre
and weight information scrolling, it does
not need adjust. Continue inflating until

it is up to the proposed pressure value
if the pressure is too low.

If the pressure is too high, press the
metal valve pin in the middle of the
valve to discharge. Inspect the tyre
pressure again with the tyre gauge.

Make sure that the valve cap is installed
back to the valve pin. The valve cap
can prevent the dust and moisture from
entering.

-35

MO TORS

Tyre

The high quality tyre equipped on your
new vehicle is manufactured by a tyre
manufacturer who is leading the way in
this industry. If you have any question
about tyre guarantee and where to
maintain, please refer to the guarantee
and maintenance instruction made by
Jianghuai Automobile Co., Ltd.

Side wall tags of the tyre
Available tyre information is mould
pressed on the side wall of the tyre.
Inflation pressure of the tyre
The tyre can only work effectively with
the proper inflation pressure.

淫 The insufficient inflation of the tyre
is dangerous as well as the overloaded
tyre. The accident caused by them may
lead to serious accident injury. Inspect
all the tyres regularly to maintain the
proposed pressure value. Inspect the
pressure of the tyre in cold conditions.
淫 If the inflation is excessive, the tyre
may be easy to be cracked and punc鄄
tured or may burst because of a sudden
pumping (for example, hit the hole).
Therefore, the tyre should ensure the
proposed pressure value.
淫 Old and broken tyre may cause
accident. Replace the tyre in time if the
tyre has been broken or its surface is
abrasion.

Notes

It is dangerous that the tyre is lack of
guarantee and used improperly.
淫 The overloaded tyre may cause
overheating of the tyre because of the
oversize friction force. Thus, the tyre
leaks gas which may lead to serious
accident.

-34

Notes

Do not think that the insufficient inflation
or excessive inflation of the tyre is no
difference. But it is not the case, if the
tyre inflation is insufficient, it will cause:
淫 Excessive deflection or distortion
淫 Overheating
淫 Overload of the tyre
淫 Early or irregular abrasion
淫 Bad maneuverability
淫 The reduction of the fuel economi鄄
cal efficiency

-37

When to replace the old tyre

You can determine when to replace the
tyre according to the abrasion indication
mark on the tyre surface. When the tyre
surface is worn and its thickness is
1.6mm or below, the abrasion indication
mark on the tyre surface will appear.
If found any one of the following condi鄄
tions, replace the tyre with a new one:
淫 There are at least 3 abrasion indi鄄

cation marks on the tyre.
淫 The tyre rubber takes on yarn or
cord.
淫 The tyre surface and tyre side
cracks, and the cracks are deep e鄄
nough for seeing the yarn or cord.
淫 There are lumps, upwarping and
layering on the tyre.
淫 The tyre is punctured and broken or
it has other damages. The damage
range and places are difficult to repair.

Purchasing new tyres
See the tyre and weight information
scrolling on the vehicle, and know about
the required tyre model and size.
Make sure that the size, load index,
speed grade and structure type (diago鄄
nal tyre, bias belted tyre or braced -
tread tyre) of the replaced tyre are the
same as that of the original tyre.

Notes

Intermix using tyre may cause the vehi鄄
cle out of control when driving. If you
intermix using the tyre of different size
or model (braced-tread tyre and bias
belted tyre), you will not control the ve鄄
hicle normally, and may cause acci鄄
dent. The vehicle will be damaged for
using the tyre of different size. There鄄
fore, the same size and model tyre
must be used for all the wheels.

Indication point 野A冶 of tyre surface abra鄄
sion mark position (six points are uniformly
distributed around.)

MO TORS

Tyre inspection and rearrangement
Rearrange the tyre from every 8000 to
13000km.

Rearrange the tyre as soon as possible
and inspect the wheel alignment if ab鄄
normal abrasion is found. Meanwhile,
inspect whether the wheel or tyre is
damaged.

The purpose of regular tyre rearrange鄄
ment is to make the tyre abrasion to be
even. The first rearrangement is the
most important.

When rearranging the tyre, make sure
that rearrange the tyre in proper mode
shown in the figure.
Do not use compact spare tyre when re鄄
arranging.
After rearranging, adjust the inflation
pressure of front and rear tyre in accor鄄
dance with the tyre and weight informa鄄
tion scrolling. Make sure that all the
wheel nuts are fixed properly and tightly.

Notes

The rust or dirt on the wheel or wheel
connecting parts will make the wheel
nuts loosen after a long time. The wheel
may come off the vehicle and lead to
accident. Before replacing the wheel,
any rust or dirt on the wheel or wheel
connecting parts must be removed. Re鄄
move them with cloth or tissue in an e鄄
mergency; after that, remove all the rust
or dirt with strickle and steel wire brush
if necessary.

-36

Notes

The cleaning articles have harmfulness.
Some are poisonous. Moreover, some
cleaning articles may burn if there is
fire near them or heat parts contact
them. It is dangerous to absorb the
smoke and dust in the close space.

Appearance curing

Be sure to conform to the warning and
instruction of the manufacturer on the
container when cleaning the vehicle with
cleaning articles. Make sure that the
vehicle door or window is open when
cleaning the inside of the vehicle.
Do not use the following articles to clean
the vehicle:
淫 Petrol
淫 Benzene
淫 Naphtha
淫 Carbon tetrachloride
淫 Acetone
淫 Coating thinner
淫 Oil of turpentine
淫 Paint thinner
淫 Nail polish remover

These articles are all harmful. Some are
more harmful than others, but all of them
can damage the vehicle. Therefore, un鄄
less the instruction indicates, do not use
the above mentioned cleaning articles.
In many circumstances, the following
articles may damage the vehicle:
淫 Alcohol
淫 Washing soap
淫 Bleaching powder
淫 Reducing agent

Textile/carpet
Frequently remove dust and scum with
vacuum cleaner. Wipe the polyethylene
resin surface, leathering and painting
surface with clean wet cloth.
You can get the authorized cleaning arti鄄
cles from the Special After-sale Service
Center of Jianghuai Automobile Co., Ltd.

-39

MO TORS

Wheel alignment and tyre balance
To prolong the service life of the tyre as
much as possible and provide the best
integral performance, the wheel align鄄
ment and tyre balance are conducted
before leaving the factory. There is no
need for regular adjustment of the wheel
alignment and tyre balance. However, if
found any abnormal abrasion of the tyre
or off tracking of the vehicle, inspect the
wheel alignment. If driven on the flat
road and the vehicle takes on bumping,
you need balance the tyre and wheel a鄄
gain.
Replacement of wheel
Replace the wheel which is bent,
cracked, seriously rusty or corrosion. If
the wheel nut is loosening frequently, re鄄
place the wheel, wheel bolt or wheel

nut. If the wheel leaks gas, replace it
(expert some aluminium wheel that can
be repaired).
The load capacity, diameter, width and
offsetting as well as the installation
method of the new wheel should be the
same as that of the original wheel.
If the wheel, wheel bolt or wheel nut
need to be replaced, use the original
new components only. Thus, it can en鄄
sure that the wheel, wheel bolt or wheel
nut are matched with your vehicle.

For the details, see the 野flat tyre re鄄
placement冶 for the treatment in an emer鄄
gency.

which may cause accident and hurt
yourself and others. So, remember to
use proper wheel, wheel bolt or wheel
nut.

Notes

U sing wrong wheel may cause prob鄄
lems in such respects as service life of
bearing, brake cooling, car speed meter
or odometer verifying, headlamp focus鄄
ing, bumper height, ground clearance of
the vehicle, clearance between the tyre
and the body and bottom plate, etc.

-38

Notes

It is dangerous to use unsuitable wheel,
wheel bolt or wheel nut, which will influ鄄
ence the brake and drivability of the ve鄄
hicle. It will make the tyre leak gas and
lead to out of control of the vehicle,

-41

continue cleaning according to the in鄄
struction about soda water in the former
text of this section.

Special cleaning problem of textile
The stain caused by such things as
tomato paste, coffee, eggs, fruit, fruit
juice, mild, soft drinks, vomit, urine or
blood can be removed according to the
instruction about using soda water in the
former text of this section. If there is still
abnormal smell after cleaning the vomit
or urine, clean the area with soda water.
The preparation proportion is a soup
spoon (5ml) of soda to a cup (250ml) of
mild water. Dry it after cleaning. The
stain caused by oil and grease can be
removed by the detergent authorized by
Jianghuai Automobile Co., Ltd. with
clean white cloth.

1. Scrape the excessive stain carefully.
2. Clean with cold water and ensure
complete drying.
3.

If the stain is not removed, clean accord鄄

ing to the instruction of the above men鄄
tioned 野Cleaning textile with detergent冶.

Leather cleaning
Remove them with soft cloth dipped into
mild water and neutral soap or leather鄄
ing soap, and dry with soft cloth. Let it
dry naturally and do not oven drying.
淫 Use leather detergent if there are
serious stains.
淫 Prohibit using oil, paint, solvent
based detergent or abrasive detergent,
furniture oil polish or shoeshine on
leather.
淫 Clean the leather at once when it is
dirty. If the stain is permeated into the
inner of the leather surface, it may dam鄄
age the leather.

MO TORS

Friendly tips

The following several hints are for
cleaning:
淫 Be sure to read the instructions on
the label of the detergent.
淫 Clean the stain as soon as possi鄄
ble before they solidified.
淫 Scrape excessive stain carefully.
淫 Use clean cloth or sponge and
change the clean places of the cloth or
sponge for cleaning. Use soft brush to
clean the serious stain.
淫 To avoid leaving ring trace after
removing stain, clean the whole area at
once, otherwise, the ring trace will not
be removed.

-40

Most stain can be removed by soda
water. Conform to the following instruc鄄
tions when cleaning:
1. Liquid stain: remove stain with clean
and soft white cloth. Solid stain: remove
them as soon as possible and then
clear off with cleaner or soft brush.
2. Dip soda water on the clean and soft
white cloth. Do not saturate too much, the
softclothshould nothavedropping waters.
3. Clean the entire area. Avoid making
the textile too wet.
4. Begin cleaning from the seam to the
stain and avoid leaving ring trace.
5. If the cloth is dirty, change to use its
other clean parts.
After removing the stain, soak up the
water in cleaning place with another
clean and soft white dry cloth.

Cleaning textile with detergent
1. First of all, try to clean the place on
the textile that it is not easy to be seen,
and make sure that the cleaning will not
influence the color of the textile.
2. Liquid stain: remove stain with clean
and soft white cloth. Solid stain: remove
them as soon as possible and then
clear off with cleaner or soft brush.
3. Spray little detergent on the clean
and soft white cloth. Do not directly
spray the detergent on the textile.
4. Begin cleaning from the seam to the
stain and avoid leaving ring trace.
5. If the cloth is dirty, change to use its
other clean parts.
6. After removing the stain, soak up the
water in cleaning place with another
clean and soft white dry cloth.
If there is ring trace of detergent left,

Notes

Prohibit cleaning or polishing the alu鄄
minium decoration parts with automo鄄
bile or chroming polishing agent, steam
or alkaline soap lye.
These materials have abrad ability
which can damage decoration parts
and wheel.

Notes

Prohibit cleaning aluminium wheel or its
decoration cover with abrasive deter鄄
gent or bursh.

The vehicle of JAC is manufactured to
be operated under normal environment
conditions and natural factors.

Polishing and waxing
Regularly polishing can clean the
residue on the surface of the vehicle.
Protect the vehicle with good quality of
wax after polishing.
Protect the bright metal parts outside
the vehicle.
Regularly clean the bright metal deco鄄
ration parts. Normally, wash with water.

When waxing for the vehicle, do not for鄄
get to wax the bright metal parts.

Clean aluminium wheel and its decora鄄
tion cover
To maintain the original appearance of
the wheel and its decoration cover,
keep off the dust or brake mill dust on
them. Regularly clean the wheel/wheel
decoration cover.

荫

Prohibit washing the engine hatch,

especially for the light fittings with high
pressure squirt gun to. Because of high
pressure of the squirt gun, the acces鄄
sories on the light fittings will loosen
and drop off, and such parts as venti鄄
lating hole and wire harness plug -in
will be affected with damp, which will
result in water entering and accumula鄄
tion of the moisture, and produce seri鄄
ous fog.

-43

MO TORS

Notes

荫

Prohibit cleaning the vehicle with

household dish washing detergent. The
lacquer wax can be removed by the
dish washing detergent.

荫

Avoid high pressure when washing

the vehicle, because water can enter
the vehicle and damage the inner of the
vehicle.

Notes

If clean the glass surface of the vehicle
with abrasive detergent, it will scuff the
glass. So when cleaning the glass, only
uses soft cloth and glass detergent.

Cleaning console
Clean the upper surface of the console
with neutral soap and water only. The
spray including Si and paraffin will make
the front windscreen have annoying
glint. In some conditions, it may serious鄄
ly influence the view permeability of
front windscreen.
Cleaning inner plastic parts
Clean those only with soft cloth or
sponge dipped into the neutral soapy
water. Commercial detergent may influ鄄
ence the surface brightness.
Cleaning glass surface

Clean glass frequently. Clean the to鄄
bacco soot and dust left on the glass
surface in the vehicle with authorized
detergent supplied by Special After -
sale Service Center of Jianghuai Auto鄄
mobile Co., Ltd. or household liquid
glass washer. Refer to 野appearance
curing冶 of this section.
Cleaning sealing strip of door and win鄄
dow
Si grease can increase the durability
and sealing performance of the sealing
strip of the door and window, and avoid
clamping or creak. Paint Si grease on
the sealing strip with clean cloth. Paint
Si grease more frequently if the whether
is cold and wet.

Cleaning the vehicle
The best way to maintain the vehicle
finishing coat is that washes it regularly
and keeps it clean.
Park the vehicle in the place without di鄄
rect sunlight.
Clean the vehicle with designated neu鄄
tral soap lye or mild water.
Be sure to clean the soap lye and de鄄
tergent on the surface.

-42

-45

Body chassis maintenance
Deicing agent, thawy agent and dust
preventive may be collected in the bot鄄
tom of the body. If those are not removed,
the parts in the bottom of the body such
as fuel pipe, frame, floor board and ex鄄
haust system will be eroded or corroded
because of rust, even they have corrosion
prevention performance.
The above mentioned foreign matter
should be removed from the bottom of
the body with water at least in every
spring. Clean all the parts collected with
earth dirt. Loosen the dirt near the frame
area with shovel before washing. The
body bottom cleaning work can be
conducted by body bottom cleaning
device or you can have it cleaned in the
Special After -sale Service Center of
Jianghuai Automobile Co., Ltd.

If these materials are disposed improper鄄
ly, they will permanently damage the
environment.

Notes

When washing the engine room, the
sediments of fuel, lubricating grease and
oil may be washed into the environment.
Wash the engine in the Special After -
sale Service Center of Jianghuai Auto鄄
mobile Co., Ltd. or other places that
has oil separating equipment.
Dispose the old engine oil, brake fluid,
gearbox oil fluid, anti-freezing solution,
storage battery and tyre in the waste
disposal agency regulated by the local
law or dispose them by the dealer who
has legal disposal obligation when re鄄
placing these materials.
Prohibit mixing these materials in the
household garbage or pouring into
sewer.

MO TORS

-44

Prevention of corrosion
The vehicle of JAC has the ability of
corrosion prevention. Special materials
and protective paint are used for most
automobile components, which is good
for the appearance, its strength and reli鄄
ability.
Although the surface of some parts in
engine room or at the bottom of the ve鄄
hicle body will be rusty, it will not influ鄄
ence their reliability or function.
Damage of sheet-metal parts
Make sure that suitable anti-rot materi鄄
als are used by repair factory to recover
corrosion prevention performance, if the
vehicle body needs repair or replace.
The replacing parts of original factory
can ensure its corrosion prevention per鄄
formance and guarantee.

Foreign matter deposit
The following materials may damage the
surface of the paint:
淫 Lime chloride and other salt.
淫 De-icing agent.
淫 Pavement oil and asphalt.
淫 Sap.
淫 Bird manure.
淫 Industrial dust.
Clean the harmful materials on the vehi鄄
cle in time. If the residue cannot be re鄄
moved by soap water, use special de鄄
tergent.

Damage of paint surface
The pit, crack or deep scratch impacted
by stone should be repaired at once, for
bare metal can be eroded soon. The fee
for after corrosion maintenance is ex鄄
pensive.
Little pit or scratch can be repaired with
the patching materials provided by the
Special After -sale Service Center of
Jianghuai Automobile Co., Ltd. The
damage with bigger area can be main鄄
tained in the vehicle body and painting
workshop of the Special After-sale Ser鄄
vice Center of Jianghuai Automobile
Co., Ltd.

Notes

Use safety detergent which is not harm鄄
ful to the surface of the paint. Other
detergent may permanently damage
the paint.

Maintenance requirements
The maintenance interval, inspection
items and the recommended oil and lu鄄
bricant oil, which are regulated in this
instruction, are the necessary condition of
assuring the vehicle in good condition.
Any loss caused by not following main鄄
tenance plan will not be included in the
scope of guarantee.

Operation condition

Firstly, you should confirm that which is
applicable for your vehicle in the follow鄄
ing two plans. The method of confirming
maintenance plan is as follows:
General definition of the driving condi鄄
tion
The normal driving condition is driving
under condition of daily driving. You can
obey the general maintenance plan.
Severe condition
If the vehicle works under any kind of
the following condition, some items in
the maintenance plan shall be carried
out more frequently, see the data in the
野Periodical technical maintenance冶 of
the latter part of this section.
淫 Frequent driving within the short
distance which is less than 10km and
the Long time and high speed (over

170km/h) driving.
淫 Under the condition of start-and-
stop, driving in idle speed or low speed
is usually used.
淫 Running on the road which is full of
dust.
淫 Running on the hills, sandlot or
mountainous ground.
淫 Always towing vehicle
淫

Running under condition of the

busy traffic in the city. The temperature
out of the vehicle is always up to 30益
or more.
淫 To be treated as taxi, police vehicle
or transfer vehicle.
淫 Always running outside, and the
outdoor temperature is lower than 0益.

-47

MO TORS

Maintenance plan

Introduction
General introduction
This section has introduced the mainte鄄
nance plans of the vehicle. These plans
are necessary for assuring your vehicle
can supply satisfied drivability for you.
You have the responsibility to follow the
correct operation which is explained by
this instruction and maintain your vehicle.
Otherwise, it is possible to cause refus鄄
ing guarantee.
You have the responsibility to maintain
and operate your vehicle correctly. You
should assure to follow the periodical
appointed maintenance plan and the
general operating introduction as regu鄄
lated in this instruction.
You also have the responsibility to keep
all kinds of records and receipt invoices
and treat them as the evidence of the

periodical maintenance. When transfer鄄
ring your vehicle, you should hand over
these records, invoices together with the
vehicle owner instruction to the next owner.
Jianghuai Automobile Co., Ltd. has only
authorized Special After -sale Service
Center of Jianghuai Automobile Co.,
Ltd. as the distributive station of
Jianghuai automobile pure mountings.
Jianghuai Automobile Co., Ltd. has not
appointed, authorized or consigned any
the third party to act as an agent or dis鄄
tribute its pure mountings, and it will
take no responsibility of the results
caused by that. At the same time, the
direct or indirect malfunction or break鄄
age
caused by using the non-pure mount鄄
ings which is not of Jianghuai Automo鄄
bile Co., Ltd., are not included in the
scope of quality guarantee.

The spare parts and accessories, which
are not produced by Jianghuai Auto鄄
mobile Co., Ltd., are not passed the
check and the approval of Jianghuai
Automobile Co., Ltd. Jianghuai Auto鄄
mobile Co., Ltd. can not check their ap鄄
plicability and also can not check their
safety. Therefore, Jianghuai Automobile
Co., Ltd. will not take any responsibility
for the breakage caused by using these
kinds of spare parts. Unsuitable, incom鄄
pletely and insufficient maintenances will
cause the operation problems of your
vehicle. Those causes will lead to
breakage of vehicle, accident or person鄄
al injury.

-46