JAC S7. Instruction — part 2

Push the exterior rearview mirror back鄄
ward to the car and you can fold the
mirror and put it flatly on the side sur鄄
face of the car.

Notes

Make sure the rearview mirrors are al鄄
ways under correct adjusting condition
and can be used when driving in order to
expand the vision and clearly watch the
surrounding objects and other vehicles.
If you can爷t correctly judge the dis鄄
tance between your car and other ob鄄
jects, you might cause collision acci鄄
dent and thus damage your car or oth鄄
er properties and even lead to injuries.
The improper maintenance of the rear-
view mirror will cause damages. Do not
scrape the ice on the surface of the
rearview mirror. If the ice or other ob鄄
jects restrain the movement of rearview
mirror, it is forbidden to make impera鄄
tive adjustment. Eliminate the ice with
de-icing can or warm air blower.

Notes

Do not drive when the exterior back mir鄄
ror is folded.
Otherwise, your vision will be lessened
and collision accidents might be
caused.

-14

Front seat

Instruction seat

Pull up and fix the operating lever in the
front below the seat, you can cancel the
locking condition of the seat.
Slide the seat to where you want and
then release the lever. Then try to move
the seat with your body and check
whether the seat is well locked.

Height adjustment of driver爷s seat

The adjustment hand wheel of the man鄄
ual driver爷s seat locates at the exterior
side of the seat.
You can adjust the inclination of the
front part of seat by screwing the hand
wheel in the front. And you can adjust
the inclination of the rear part of seat by
screwing the middle hand wheel.

Notes

When driving the car, the adjustment of
the instruction seat of the driver爷s might
cause your car out of control, as the
sudden movement of seat might scare
you or make you be at wit爷s end, or
make you step on certain pedal sub鄄
consciously. You can adjust the driver爷
s seat only when the car is stopped.

-15

MO TORS

Inclinable seat backrest adjustment

The instruction lever, which locates at the exte鄄
rior side of the seat, is equipped in your car
to control the inclination of your backrest.
To adjust the seat backrest, lift the lever
and adjust the backrest to where you
want. Then, loosen the lever and push
backward the seat backrest, making
sure that the backrest is well locked.
Pull up the lever and the seat backrest
will move to vertical position.

Electric seat (if equipped)

If your car is equipped with this device,
there will be a multi -direction adjust鄄
ment electric seat control device at the
exterior side of driver爷s seat.
The adjusting method of electric seat is
as follows:
Push the switch forward or backward and
the seat can be moved fore and aft.
Press the front part of the switch up鄄
ward or downward, and you can lift or

lower the front part of the seat.
Press the rear part of the switch upward
or downward, and you can lift or lower
the rear part of the seat.
Push the entire switch upward or down鄄
ward, and you can lift or lower the entire
seat.

-16

Push the switch on the upper side for鄄
ward or backward, you can adjust the
inclination of the seat backrest.
When your seat reaches to where you
want, please loosen the switch.

Instruction waist rest (if equipped)

To adjust the waist rest of the driver爷s
seat, please use the control lever at ex鄄
terior side of the seat backrest.
Push the lever downward, and the waist
rest can be adjusted to the lower posi鄄
tion of the backrest.
Pull the lever upward, and the waist rest
will return to normal position.

Do not incline the seat backrest when
your car is running.

-17

MO TORS

Notes

When the car is running, it is very dan鄄
gerous to sit on the seat with inclined
backrest. Even if you have already tied
the safety belt, it won爷t act if your body
is so much inclined; neither will be the
shoulder belt as it cannot closely cling
to your body. The shoulder belt lies in
your front side, and when the car col鄄
lides, you might clash onto the shoulder
belt, injuring your neck or other body
parts. The hip belt could neither act, for
during collision process, this belt will
slide to the upper side of your ab鄄
domen. The effect of hip belt still exists
but not on your hipbone position, which
will cause serious internal injuries.

Pillow

Adjust the pillow height and make its
upper side approach your crown as
much as you can, so as to minimize the
chances of your neck getting injured
during the car collision.
Lift: pull up the pillow and you can ad鄄
just the pillow height.

In order to protect the passengers in鄄
side the car when driving, the seat
backrest should be at vertical posi鄄
tion. Then lean against the back part
of the seat as much as you can and
correctly wear the safety belt.

-18

Descend: While pressing down the lock鄄
ing release button, press the pillow down.
To dismount the pillow, please fully pull
up the pillow, and then press the re鄄
lease button and lift the pillow from in鄄
side the guiding sleeve.
Before driving, the pillow should be re鄄
assembled and readjusted to the origi鄄
nal position.

Rear seat

The two exterior seats in rear row and
the middle seat are all equipped with

three-point safety belt.
To use the middle handle of rear seat,
pull out the middle handle with cup sup鄄
port installed as shown in the above pic鄄
ture.

-19

MO TORS

Notes

淫 When driving, the diver must be
able to completely control the steering
wheel.
淫 When driving, do not adjust the
position of the steering wheel. The ad鄄
justment of steering wheel when you
are driving will make your car out of
control.

Inclinable steering wheel

To adjust the position of steering wheel:
1. Push downward the control lever at
the lower pat of steering column.
2. When reaching the required position,
pull upward the control lever to lock the
steering wheel.
3. Make sure that the steering wheel is
completely locked.

-20

1. Air outlet
2. Combined device
3. Hi-fi system (refer to Chapter 4 Vehi鄄
cle Equipment)
4. Gas filler cover opening switch
5. Backup hatch cover opening switch
6. Background light brightness regulat鄄
ing switch

7. Engine hatch cover release bar
8. Storage box at driver爷s side
9. Headlight height regulating switch
10. Reserved switch (no function tem鄄
porarily)
11. Front fog lamp switch
12. Rear fog lamp switch
13. Cigarette lighter and ash tray

14. Hazard warning flashing light switch
15. Temperature control system
16. Rear windshield defroster switch
17. Reserved switch (no function tem鄄
porarily)
18. Glove compartment
19. Horn

Console

-21

MO TORS

Combined device

-22

1. Tachometer 2. Car speed meter 3. Thermometer 4. Fuel oil meter 5. Mileage/shift/time indicator light

Charging and discharging indicator light

Brake shoe abrasion indicator

Oil pressure alarm

Safety belt indicator

Fuel alarm

Safety airbag indicator

EPC

Engine check

ABS alarm

Small light indicator

Door ajar indicator

Distant light indicator

Engine anti-theft indicator

Front fog lamp indicator

Boot indicator

Rear fog lamp indicator

OBD indicator

Left/right steering indicator

CRUISE

Cruise indicator (if equipped)

Parking brake and braking liquid level warning/EBD

-23

MO TORS

-25

Fuel gauge

I

ndicating the amount of fuel remained

in the tank.
After refilling the oil and restarting the
engine, the pointer of fuel gauge moves
slowly and indicates a new oil level.
During braking, accelerating or turning
processes, the fuel oil inside the tank
will swing, which will lead to the move鄄
ment of fuel oil tank pointer.
Volume of fuel oil tank: 70L

Thermometer

Indicating the water temperature of the
engine. When the pointer reaches the
red area, the car must be stopped for
overhaul, preventing the engine dam鄄
age. It should not be restarted until the
water temperature decreases. If such
similar fault still exists, please promptly
contact with the special service center
of Jianghuai Automobile Company.

Mileage/ shift/ time indicator light

With accumulated mileage, mileage
subtotal and time showing function
淤 is the time and mileage subtotal me鄄
ter
于 is the accumulated odometer

MO TORS

Tachometer

The tachometer indicates the number of
revolution of the engine per minute.
In order to improve the fuel economical
efficiency, you should keep the revolu鄄
tion speed at low scope from 2,000r/m
to 3,000 r/m when driving.
Do not operate the engine when the
pointer of tachometer enters the red
area.

Speed gauge

The speed gauge indicates the speed
by km/h.

Notes

The over-revolution of engine will dam鄄
age the engine. Do not let the engine
rotate too fast which will move the point鄄
er into red area. Otherwise, expensive
repair charges may be incurred.

-24

-27

Hour setting
The hour setting mode will be accessed
if the regulating lever is pressed and
held for long period (more than 2s) un鄄
der the clock setting mode. Under the
hour setting mode, the hour will increase
along with the short press of regulating
lever (>300ms and <2s). If the time of
regulating lever pressed is more than
2s, the hours will continuously increase
by 5h once. If the regulating lever hasn爷
t been contacted within 5s, it will enter
the minute setting mode. At this mo鄄
ment, the minute digits and colon flash
at 1Hz.

Minute setting
The regulating lever will enter minute
setting mode when the lever is pressed
for long period (more than 2s) under the
hour setting mode.
Same as the hour setting, if there is no
contact of regulating lever within 5s, the
minute setting mode will terminate and
the clock will not flash at this moment.

Indicator light and warning light

Charging and discharging indicator light
As one check, when the ignition switch
is connected and the engine is not start鄄
ed, the charge system indicator light will
turn on shortly, indicating it under nor鄄
mal condition.
After the engine is started, this indicator
light should turn off. If the indicator light
doesn爷t distinguish or lights up during
driving process, it indicates the charging
system may have electrical failure. You
should visit the after sale service center to
check the charging system. If you drive
with this light on, the battery will be used up.
If you have to drive in short distance
with this light on, please shut off all the
attached devices, such as radio and air
conditioner.

MO TORS

Mileage subtotal reset and clock setting
shift

The reset lever can be used to shift a鄄
mong modes, adjust time and reset the
odometer. When operating the shift
display modes, one must press it in
short time (>300ms and <2s).

Mileage subtotal
The mileage subtotal is displayed on the
upper row of LCD, indicating the total
mileage from the previous subtotal reset
or the battery pressure cut-off till now.
Its display scope is 0-999.9kms, with a
precision of 0.1km. If the instrument
power is cut off (the battery power in鄄
stead of the ignition power), the mileage
subtotal meter will be reset.
Reset the mileage subtotal meter
Under the display mode of mileage
subtotal meter, if you press and hold the
regulating lever for long period (more
than 2s), the current readout in mileage
subtotal meter will be reset.

Clock
Both the time and clock sign are simul鄄
taneously displayed on the upper row of
LCD, with the time displayed using 24-
hour system.
Clock setting
The time is displayed in the form of 24-
hour.
Press down and hold the regulating
lever for long period (more than 2s), the
clock setting mode will be accessed. At
this moment, the hour digits and the
colon flash at 1Hz.

-26

Friendly Tips

If the engine oil is in shortage, it may
damage the engine and the mainte鄄
nance caused by this is not within the
warranty scope. Please replace the en鄄
gine oil as per the maintenance sched鄄
ule in this Instruction.

Notes

When the engine oil pressure is too low,
do not continue driving. Otherwise, the
engine will overheated and caught on
fire, which will injure people. You
should check the engine oil and send
the car for repair as soon as possible.

Engine oil pressure alarm light
If the engine oil pressure is too low, this
alarm light will keep turning on after the
engine is started. If the light lights on
when the car is driving, it indicates the
engine oil is insufficient. This is caused
by the lower of engine oil level or other
faults related with the oil. Please find the
special sale and service center of
Jianghuai Automobile for check. The
engine oil alarm light may also light up
under another three situations:
淫 As a kind of test, when the ignition
switch is connected but the engine is
not started, this alarm light will switch
on, indicating its function is normal. Af鄄
ter the engine is started, this alarm light
will distinguish. If the ignition switch is
connected but the light isn爷t on, it is the

fault of fuse or bulb.
淫 If the engine idles when coming
across red lamp, the alarm light may
flash and then distinguish.
淫 If you conduct emergency brake,
this light will be on for short time, which
is very normal.

-28

Notes

Do not drive the car when the fault indi鄄
cating light is on.
The indicator light indicates that your
car has faults that need paying atten鄄
tion. Driving when the fault indicator
light is on will damage the exhaust
control system and influence the fuel e鄄
conomic efficiency and the car perfor鄄
mance.
Please find the special after service
center of Jianghuai Automobile for re鄄
pair and maintenance as soon as pos鄄
sible.

Fuel alarm light
When the fuel tank level is too low, this
alarm light will be on.
When the remaining oil in the tank ap鄄
proaches 7.5L, the fuel level too -low
alarm light will turn on.
After refill fuel into the fuel tank, the
alarm light will distinguish.

Engine check indicator light
After the ignition switch is connected
and before the engine is started, the in鄄
dicator light will light on.
This indicates the indicator light bulb is
in normal condition.
The light will distinguish after the engine
is started.

-29

MO TORS

Notes

Do not drive the car when the brake
system alarm light is still on.
It may indicate that your brake works
abnormally.
Driving with brake faulted may cause
collision accidents and result in bodily
injuries, and even damage your car or
other objects.

Distant light indicator light
When the distant light of headlight is
connected, the distant light indicator
light will be on.
Small light indicator
The small light will be used at dark but
it爷s still bright outside. At this moment,
the small light indicator light will be on.
Front fog lamp indicator
When the front fog lamp lights on, the in鄄
dicator light will be on.
Rear fog lamp indicator
When the rear fog lamp lights on, the in鄄
dicator light will be on.
Left and right steering indicator
The turning signal light indicator light is
to confirm whether the outside turning
signal light is in normal condition.
If the green arrow fails to flash when you

send out the turning signal or press
down the hazard warning button, check
the fuse and bulb and replace if neces鄄
sary.
Parking brake and braking liquid level
alarm light
After the ignition switch is connected
and before the engine is started, the
brake system alarm light will turn on.
This indicates the indicator light is in
normal condition. After the engine is
started, this light will light on together
with the ABS indicator light, which indi鄄
cates the system is under self -check
and the indicator light bulb in normal
condition. The light should distinguish
after around 2s.
When the parking brake is connected,
the brake system alarm light will also

light on. The indicator light will be out af鄄
ter the parking brake is loosened.
Please loosen the parking brake before
driving the car.

-30

If the brake system alarm light is still on
when the parking brake is completely
loosened, it indicates the braking liquid
level inside the storage tank is too low.
To deal with it, you should perform the
following procedures:
1. Carefully drive your car away from
the pavement and stop it.
2. Check the braking liquid level.
3. Add the recommended braking liquid
up to appropriate position. Refer to
Chapter 7 野Maintenance冶 for details.

Brake shoe abrasion indicator
This light will turn on if the brake shoe is
seriously worn out and unable to ensure
the stability of brake.
Safety belt indicator
When the ignition switch is turned on,
the alarm LED will not work if the safety
belt is connected.
When the ignition switch is placed at
ON position, if the driver forgets to tie
the safety belt, the safety belt warning
light will flash in an interval of 0.3 依
0.1sec and the door bell sound in an in鄄
terval of 0.45依0.1sec, taking 6依1sec as
a whole cycle. Whenever the car speed
rises from less than 20km to 20km, the
instrument also needs to output the
control signal and control the door bell
to sound for one cycle (6依1sec); if the

safety belt is well tied within one cycle,
the chirping will stop.
When the ignition switch is placed at ON
position, if the driver well ties the safety
belt, the safety belt alarm light will flash for
one cycle (0.3依0.1sec) without giving off
any hint sounds; when the safety belt is
untied, the alarm light flashes and gives
off hinting sound. It will stop when the
safety belt is properly tied once again.
Connect the safety belt when the igni鄄
tion switch is turned on. During driving if
the belt is disconnected, the alarm LED
will light on.

-31

MO TORS

Safety airbag ready indicator light
There is one airbag indicator light on the
console showing the symbol of airbag.
The system will check whether there is
fault on airbag system. Through this
light, you will know whether there is
electric fault in airbag system. The sys鄄
tem will check airbag sensor, airbag
module, circuit and diagnosis module.
When the car is started, this light will be
on for around 7s and then distinguish,
which indicates that the airbag system
is fully prepared.
If the airbag ready indicator light keeps
on when the car is started or lights on
when driving, it indicates there is abnor鄄
mality in airbag system and the car
needs repairing right now.

ABS alarm
Your car is equipped with anti -lock
braking system (ABS), and when the ig鄄
nition switch is turned on connecting po鄄
sition, this alarm light will keep lighting
on for several seconds. This is very nor鄄
mal.
If this alarm light keeps on, do not drive
the car. If the alarm light lights on sud鄄
denly, please stop the car and shut off
the ignition switch as soon as possible,
and then restart the engine and reset
the system. If the alarm light still keeps
on or lights on during driving, the car
needs to be repaired. If the routine
brake system alarm light (i.e. parking
brake and braking liquid level alarm/
EBD alarm light) fails to light on, the car
can still be stopped, but cannot perform

anti -lock brake. If the routine brake
system alarm light also lights on, not on鄄
ly the anti-lock brake is out of work, but
also the routine brake system has prob鄄
lems.
Door ajar alarm light
When the ignition switch is connected,
this indicator light will keep lighting on
until all doors are closed and completely
locked.

-32

Engine anti-theft indicator light
There is electronic chip installed inside
the ignition key of the automobile. Inside
each chip installs a fixed ID (equals i鄄
dentification number). And only then the
ID on key chip is consistent with the ID
at the engine's side can the car be
started. On the contrary, if inconsistent,
the car will automatically cut off the cir鄄
cuit at once and disable the engine to
be started.
淫 Once the ignition switch is turned to
野ON冶 position, the alarm light will light
on for 2s.
淫 When at sleep mode, the alarm light
will flash according to the following fre鄄
quency: light up for 50ms for every 2s.
淫 If the password is verified incorrect,
the alarm light will flash at the following

frequency: once every 1s.
淫 If the password is verified correct,
the alarm light will switch off.
淫 If at working diagnosis mode, the
alarm light will switch off.
The constant flashing of anti-theft start鄄
ing indicator light may be caused by
fault of anti-theft starting system or sig鄄
nal interference; you only need to turn
the ignition switch to ON first and start
the engine after the anti -theft starting
light distinguishes several seconds later
according to normal operation. Repeat
the start-up procedure for several times
and the anti-theft starting system will re鄄
set to normal condition. If you still can鄄
not eliminate the fault, please check
your car at special maintenance shop of
Jianghuai Automobile.

Boot indicator
This indicator light will be on when the
boot is opened.
EOBD
EOBD will light up the fault indicator
light and record a diagnosis fault code
when the exhaust of Hydrogen Com鄄
pound (HC), Carbon Oxide (CO) and
Nitrogen Oxide

(NOx) exceeds the

EOBD exhaust limit specified by the ex鄄
haust rule. If the EOBD light of your car
suddenly light up when driving, lease
stop the car and shut off the engine at
once, and then restart the engine. If the
indicator light is still on, please check
and repair your car to the special ser鄄
vice shop of Jianghuai Automobile.

-33

MO TORS

Notes

When the hazard warning flashing light
is connected, turning signal is unable to
be sent out.

Cruise indicator (if equipped)
If the 野CRUISE冶 indicator keeps on, it
indicates that the system is still working.
Close the cruise control and the
野CRUISE冶 indicator light will distinguish.
In case of any of the following situations,
it indicates that the cruise control sys鄄
tem has fault:
1. Indicator light fails to light on.
2. Indicator light flashes once more.
3. Indicator distinguishes after lit up.
Under such circumstance, please con鄄
tact with the dealer and have your car
checked.

Hazard warning flashing light

The hazard warning flashing light is
used to give off warning to other people
as well as to tell the police that you
have met with troubles. The turning sig鄄
nal lights in the front and rear part of the
car and the side turning light will flash.
The button for hazard warning flashing
light locates at the middle position of the
mid switch group assembly of instru鄄
ment desk.
Wherever the ignition switch locates and
even if the ignition key is not inserted,
the hazard warning light will work. By
pressing down this button, the front and
rear turning signal lights and the side
turning light will flash. The flashing lights
can be turned off if this button is
pressed once again.

Other warning devices

If you take with reflective tripod, you can
set it at around 100 meters backwards
your car at the roadside.

-34

Turning signal/multi-function control lever (as follows)

Types

Switch position

Work shift and function

Description

Right handle

function

(windshield

wiper switch)

Inching position

Handle can automatically reset at this position Handle temporarily lifted

Close

Windshield wiper off

0 position

Intermittent

Windshield wiper works intermittently

Turn the handle downward to the 1st shift

Low speed

Windshield wiper works at low speed

Turn the handle downward to the 2nd shift

High speed

Windshield wiper works at high speed

Turn the handle downward to the 3rd shift

Intermittent shift

When at intermittent operation,

control the intermittence interval

Rotate the rotary button at the end of handle

Washing apparatus

Spraying water and then wipe it clean

Lift the handle towards the driver爷s direction

until the washing solution splashes out

Left handle

(light and signal

indicator light

switch)

Change lane leftward

Left turning light lights on

Temporarily turn the handle downward

Change lane rightward

Right turning light lights on

Temporarily turn the handle upward

Left turn

Left turning light lights on

Turn the handle downward to the locking

Right turn

Right turning light lights on

Turn the handle upward to the locking position

Close

Lights out

Rotate the rotary button at the end

of the handle to 0 position

Parking light

Parking light on

Rotate the rotary button at the end

of the handle to 1st shift

Headlight

Headlight and parking light on

Rotate the rotary button at the end

of the handle to 2nd shift

Change of high beam light

and dipped headlight

Realize the exchange of distant

and dipped beams

Pull the handle towards the driver爷s

direction until locking position

Headlight flash

Control the main beam

Pull the handle toward the driver爷s

direction slightly and then loosen

-35

MO TORS

Turning signal/Multi -function control
lever

Turning and lane changing signal

There are two upward positions (right
turning) ad two downward positions (left
turning) on the turning signal control
lever. These positions will be used to
send out signals for turning and lane
changing.

To send out the turning signal: push the
control lever upward or downward till
the end. And when the turning is termi鄄
nated, the control lever will return auto鄄
matically.
There is an arrow on the combined de鄄
vice of the console that will be flashing,
which indicates the direction of turning
or lane changing.
To send out the lane changing signal:
You need only lift or press down the
control lever until the arrow begins
flashing. Hold the control lever until the
lane changing is terminated. When you
loosen the lever, it will return automati鄄
cally. When you give off turning or lane
changing signals, if the arrow flashes
too quickly, the signal light may be
burnt and other drivers will be unable to

-36

observe the turning signals you sent
out.
If a certain bulb is burnt, it should be
replaced at once to avoid traffic acci鄄
dents. If the arrow fails to flash when
you send out the turning command, you
should firstly check whether the bulb is
burnt and then check the fuse.

Headlight/Dipped beam exchanger

When you want to change the headlight
from dipped beam to high beam, you
should push the turning signal/multi -
function control lever opposite you.
When high beam is connected, if the ig鄄
nition switch is on, the indicator light on
the combined device will also light on.
If you want to change the headlight from

high beam to dipped beam, you should
push the turning signal/multi -function
control lever towards you.
Front headlight flashing
This function enables you to send out
overtaking signal to the front drivers by
using the high beam headlight.
When using this function, pull the turn鄄
ing signal/multi -function control lever
towards you until the high beam of
headlight lights on. Then loosen the con鄄
trol lever and distinguish the headlight.

-37

MO TORS

Front windshield wiper

Operate the front windshield wiper by
using the control lever at the right side of
the steering column. The ignition switch
must be connected to operate the wiper.
Clearance: turn the handle downward to
the 1st shift and select one cycle of de鄄
layed wiping and washing.
Low: turn the handle downward to the
2nd shift and you can conduct stable

low speed wiping.
High: turn the handle downward to the
3rd shift and you can conduct stable
high speed wiping.
You can also control the intermittence
interval by rotating the rotary button at
the end of handle.
Stop: turn the control lever to 0 position,
and the front windshield wiper is shut off.
When lifting the control slightly from 0
position, the front windshield wiper will
act for one cycle.

Front windshield washing solution
To washing the front windshield, pull the
front windshield wiper washing solution
control lever toward the driver when the
ignition switch is connected. The wash鄄
ing solution will splashed out from the
front windshield spray nozzle.
When you loosen the lever, the washing
apparatus will stop working, but the
wiper will continue acting for another
two cycles. Then you can choose to
stop the wiping or recover to the wash鄄
ing speed previously.

Friendly Tips

In cold and freezing whether, you
should not start the wiper if the front
windshield is not preheated. Otherwise,
the washing solution will froze on the
front windshield and block your vision.

-38

Friendly Tips

When using the fog lamp, the ignition
switch must be placed at ACC (annex)
or ON (connecting) position.

Friendly Tips

When using the rear fog lamp, the front
fog light must be on.

Front fog lamp

Pres s the front fog lamp button on the
mid switch group assembly of instru鄄
ment desk, the front fog lamp will be
connected and the indicator light on the
button will light on. At the same time,
the front fog lamp indicator light on the
combined device will light on. Press the
button once again and the front fog
lamp will distinguish.

Rear fog lamp

When the front fog lamp is on, press the
rear fog lamp button on the mid switch
group assembly of instrument desk, the
front fog lamp will be connected and the
rear fog lamp indicator light on the
combined device will light on. The indi鄄
cator light on the button will light on.

-39

MO TORS

Panel board brightness

The third switch on the left switch group
assembly of instrument desk is the dim鄄
ming switch which can adjust the
brightness of the light on the console.
Toggle the thumbwheel switch of the
dimming switch upward to increase the
brightness of the light, and vice versa.

Illumination angle adjustment of di -
pped beam light and high beam light

The fourth switch on the left switch group
assembly on the instrument desk is the
dimming switch of headlight which could
adjust the illumination angle of the
dipped beam light and high beam light.
Toggle the thumbwheel switch of the
dimming switch upward to upper the
beam of dipped beam light and high
beam light and vice versa.

Glove compartment

The glove compartment is equipped
with locking core. You can lock and un鄄
lock the glove compartment by the igni鄄
tion key. To open the glove compart鄄
ment, just pull upward the glove com鄄
partment handle when the compartment
is at unlocking position.

-40

Notes

Do not put inflammable substances into
ash tray. If you put paper or other in鄄
flammable substances into the ash tray,
the un-extinct cigarette head may light
them up, which might damage your car.

Cigarette lighter and ash tray

The front cigarette lighter and ash tray
locate at the lower part of the central
console with an integrated protective
cover. Press at the bright stripe ornament
part on the cover and then release, the
protective cover will open automatically.
To take out the front ash tray for clean鄄
ing, pull out the ash tray and pour the
ash. When reassembling, just push the
ash tray back.

The rear ash tray locates at the rear part
of auxiliary facia console. Pull out the
rear ash tray for cleaning. When re鄄
assembling, just first clamp it on the
bottom tongue and then push it back.

-41

MO TORS

Cup support

The cup support locates at the auxiliary
facia console and rear seat armrest. To
use the front cup support, press the
bright stripe ornament part of the cup
support protective cover and then
loosen, the cover will open automatically.
To use the rear cup support, pull down
the central handle at rear seat (refer to
the next page 野Rear Seat Armrest冶.

Storage box at diver爷s side

The storage box at driver爷s side locates
at the console at the left side of steering
wheel. It is used as the interior fuse
check mouth as well. To use it, just pull
out the storage box or take it out.

Storage area of central control console

The central control console has two in鄄
dependent storage areas and the upper
storage hatch is also an armrest. To
open the upper storage hatch, just pull
up the armrest cover plate at the upper
layer. To open the lower part storage
hatch, just lift the lower starting wrench
and raise the hatch cover. To close the

-42

storage hatch, press down the cover un鄄
til it is tightly locked.

Rear seat armrest

There are two cup supports on the rear
seat armrest. To use them, pull down
the armrest from the backrest of the rear
seat.

-43

MO TORS

-01

Chapter IV Vehicle Equipment

Temperature control

4-02

Rear window and exterior view mirror
defroster

4-06

Air outlet control

4-07

Passenger compartment air cleaner

4-07

Reverse radar system

4-08

Interior lighting

4-10

Hi-fi system

4-11

Rear windscreen antenna

4-12

Sunroof

4-12

Sunroof vanity mirror

4-12

Airbag system

4-13

Accessory power supply socket

4-14

Sun roof

4-15

Front seat pre-tension type safety belt

4-16

Rear seat three-point type safety belt

4-16

Anti-theft system

4-17

MO TORS