JAC S1. Service manual — part 5
fails during running, please park at a
safe place as soon as possible.
Warning and sound of safety
belt
When the ignition switch is turned to "
ON" or "START" position from "OFF"
position, the warning light will illumi鄄
nate for about 6 seconds. If the pas鄄
senger does not tie the safety belt,
the system will sound at the same
time.
Charging system warning light
When the ignition switch is on,
charging system warning light will il鄄
luminate. After starting the engine,
this warning light should extinguish.
Warning light illuminating during run鄄
ning indicates the failure of charging
system. If such case, drive the vehi鄄
cle to a safe place and park careful鄄
ly. First check the generator driving
belt for loosening or breaking.
Warning light for slightly open
door
When the ignition switch is in any po鄄
sition, if a door does not close tightly,
warning light and buzz will warn at
the same time.
Low fuel warning light
Illumination of this warning light indi鄄
cates that the fuel tank will be empty
soon. In this case, please add fuel
immediately.
When there is no fuel or fuel level is
below "E", if you drive the vehicle, the
engine will stop and the catalytic
converter will be destroyed.
Warning light for opening of
the trunk
When the trunk is open, this system
will warn.
Air bag warning light
When the ignition switch is in "ON"
position, or after starting the engine,
SRS warning light (SRI) will flash for
6 seconds and then extinguish.
When the SRS fails, the warning light
Note院
音 Do not lock the vehicle inside
of it, because the warning light
will still warn under the condition
that the vehicle is locked or the
door is open. In the locked po鄄
sition and when the driver door
is open, buzzer will be on.
Pulling out the key will stop the
warning light and buzzer.
Characteristics of JAC vehicle
28
will also illuminate, if it does not illu鄄
minate, or illuminate for more than 6
seconds, or illuminate during run鄄
ning, please quickly ask JAC dealer
to check.
Failure indicator of engine
This indicator is part of onboard di鄄
agnosis system, and it can monitor
different exhaust emission control
system. When the ignition switch is in
"ON" position, the indicator will illumi鄄
nate, and extinguish after several
seconds. If the running indicator illu鄄
minates or the indicator does not illu鄄
minate in the "ON" position, please
quickly ask JAC dealer to check.
Fuel gauge
Fuel gauge indicates the fuel level in
the fuel tank.
Water temperature gauge of en鄄
gine
If the engine overheats, do not open
the water tank cover; otherwise seri鄄
ous scald will occur. So, you can not
open the water tank cover until the
engine returns to normal tempera鄄
ture.
If the pointer of water temperature
gauge exceeds normal range and is
near to "H" (hot) position, which indi鄄
cates the water temperature is too
high and the engine will be dam鄄
aged. At this time, stop the engine,
open the engine cover, and check
the coolant level and water pump
belt. If there is problem in cooling
system, please ask authorized JAC
dealer to check.
29
Tachometer
The tachometer indicates engine
speed. Use the tachometer to select
correct gear, avoiding use low gear
or high gear at low speed.
Odometer
Odometer of JAC vehicle is tested in
km/h.
Accumulated/trip odometer
Accumulated odometer
Accumulated odometer indicates the
total distance that the vehicle has
run.
Caution:
音 Do not let the engine speed
reach the red area in tachome鄄
ter, because that will destroy the
engine badly.
Note院
音 Changing the odometer will
make it unable to be guaran鄄
teed. Function of digital/trip
odometer. When the ignition
switch is in "ON" position, press
down the reset button on the
right of odometer.
Characteristics of JAC vehicle
30
1援Accumulated odometer
Accumulated odometer indicates the
total distance that the vehicle has run
in kilometer.
2援Trip odometer
Recording in kilometer.
Method A: distance between your
home and the destination.
Method B: distance between middle
section and destination.
To convert from method A to method
B, please press the reset button.
Pressing for 2 seconds, the odome鄄
ter will return to zero.
multimeter
1援Transfer switch for operating mode
2援Air pressure gauge
3援Azimuth dial
4援Height measurement
5援Azimuth adjusting switch
6. Upper/lower switch
7援Light switch
8尧Upper/lower switch
9援Highway indicator
31
How to adjust multimeter
Air pressure gauge
Indicating range of air pressure
gauge is 470 ~1040 hpa.
Azimuth dial
Azimuth dial indicates the azimuth in
which the vehicle runs. The indicat鄄
ing range is 180 degree, at 22.5 de鄄
grees spacing.
How to correct the error of the az鄄
imuth indicator?
1冤Pressing the azimuth adjusting
switch for less than 5 seconds, az鄄
imuth indicator will begin to flash.
2冤Turn the vehicle slowly within 128
seconds.
3冤After turning, the azimuth indicator
will stop flash.Now, you can correct
the error.
Highway indicator
Hight measuring gauge
Height measuring gauge is dis鄄
played as "ALTI data (m)" in operat鄄
ing mode. Its measuring range is
200~2,800m. With regard to correct鄄
ed height (displayed in operating
speed
lighting frequency
lower than 2.8 km/h
total
2.8~40 km/h
1 second
41~60 km/h
0.8 second
61~80 km/h
0.5 second
81~100 km/h
0.3 second
Characteristics of JAC vehicle
32
mode), because of air pressure con鄄
version for height on sea level (0m
point), displayed height in the same
region may be different. Use the fol鄄
lowing method to correct the height
within 依 300: Press " 银" switch, and
hold on for less than 0.5 second.
Now it can be added by 50m. Press
"▼" switch, and hold on for less than
0.5 second. Now, it can be reduced
by 50m.
Related measuring gauge of
height
Use operating mode switch, display
frequency from "Altitude" to "ALTI da鄄
ta (m)" can be displayed on the op鄄
erating mode
银 indicates high height
▼
indicates low height
音 display range院依3,000m
音 Height correction method is the
same as height measuring gauge
correction method.
Front fog lamp switch
Press the switch to turn on the front
fog lamp. When the headlight switch
is in second position and the ignition
key is in "ON" position, the front fog
will illuminate.
Rear fog lamp switch
Press the switch to turn on the rear
fog lamp. When the headlight switch
is in second position and the ignition
key is in "ON" position, the rear fog
lamp will illuminate.
Combining with steering signals, op鄄
erate headlight and high beam indi鄄
33
cator switch turning signals
Pulling down the control lever, the
turning signal at left outside will flash.
Pulling down the control lever, the
turning signal at right outside will
flash. After that, control lever will re鄄
turn to middle position automatically,
and the turning signal lights will ex鄄
tinguish. If the light flash abnormally,
or does not flash, or does not act,
there may be malfunction. Check the
fuse and bulb for burnout. Or ask
authorized JAC dealer to check.
Lane changing signal
Moving the signal lever up and down
to send lane -changing signal. After
releasing it, the signal lever will re鄄
turn to middle position.
Headlight switch
Move the switch to the last position
of multifunctional switch to turn on
the headlight. First position of the
switch is for parking light, side light,
tail light and panel light. Second po鄄
sition of the switch is for headlight.
Tail (parking) light
Turn the switch to "ON" or "OFF" posi鄄
tion, to turn on or off tail (parking)
light.
High beam indicator switch
Pull the control lever towards yourself
to turn on high beam indicator. At
this time, high beam indicator will il鄄
luminate. Pull the control lever to the
opposite direction to reduce the
beam.
Headlight flashing
To change headlight beams, pull the
switch control lever towards yourself
and then release it. Even with the
Characteristics of JAC vehicle
34
headlight switch in "OFF" position,
the headlight beam can be changed.
Wind shield wiper and cleaner
Wiper switch has three operation po鄄
sitions altogether:
1援intermittent operation
2援low speed operation
3援high speed operation
Operation of wind shield cleaner
To use the cleaner, pull the control
lever towards steering wheel. After
operating the control lever, the
cleaner will operate automatically. Af鄄
ter releasing it, it will stop.
Defroster
Push the control lever of wind shield
wiper and cleaner upwards to oper鄄
ate the defroster.
Intermittent wiper
To use intermittent wiper: put the
Note院
音 In order to prevent damage
of the wiper, do not use wiper to
wipe heavy object, such as
snow or ice. If the weight of the
object is too light, you can op鄄
erate warm air to melt the rain or
ice.
Note:
音 Wiping time for one operation
must not be more than 15 seconds.
Do not operate cleaner when there
is no liquid.
音 In winter, please confirm if the
wiper blade is frozen on the window.
音 Use wind shield cleaner to pre鄄
vent the water icing.
35
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст