JAC Pick-Up. Service manual — part 11
Caution:
Touch the naked portion of the
electrode clamps under no cir鄄
cumstances. Moreover, do not
touch the auxiliary wire con鄄
nected to the positive pole of
the battery with a conductive
part- be careful of short-circuit.
The auxiliary wire shall be ar鄄
ranged properly so as not to be
wound by rotating parts in the
engine!
Do not bend and touch the bat鄄
tery - be careful of corrosion!
Keep naked flame (burning
candle or lit cigarettes) away
from the battery - be careful of
Starting Your Vehicle in an Emergency
explosion!
Should the engine fail to start
immediately and the cranking
may stop after 10 seconds,
restart it about 30 seconds later.
Should the engine start, repeat
the steps reversely to remove
two wires.
4 -11
Caution:
A discharged battery can get
frozen when the ambient temper鄄
ature is lower than 0 degree. Re鄄
member to replace the frozen
battery when using an auxiliary
wire for connection, otherwise it
may explode. Do not allow direct
contact between two vehicles as
conduction may occur when the
positive wire are fitted. The dis鄄
charged battery must be re鄄
moved from the circuit according
to operating requirements.
The engine from the source bat鄄
tery's vehicle is required to be
operated. Note adequate metal
Starting Your Vehicle in an Emergency
contact area shall be available
for connecting clamps, in particu鄄
lar for those secured on the en鄄
gine body.
A - Discharged Battery
B- Source Battery
Use following steps to con鄄
nect the auxiliary wires
1. Connect one end (+) of the
wire (Red usually) to the corre鄄
sponding pole (+ ) of the dis鄄
charged battery A.
2. Connect the other end of the
red wire to positive pole of the
source battery (+).
3. Connect one end (-) of the
wire (Black usually) to the nega鄄
tive pole (-) of the source bat鄄
tery B.
4. Connect the other end of the
black wire to a reliable metal part
reliably attached to the engine
that was unable to be started or
directly to the engine body.
4 -10
OWNER爷S MANUAL
pick-up
Free Travel of Clutch Pedal, mm 5-15
Total Height of Clutch Pedal, mm 178-188
Free Travel of Brake Pedal, mm
6-10
Total Height of Brake Pedal, mm 174-184
Tire Pressure, Front, Kpa
310
Rear, Kpa
350
Tension for Engine Belt, mm
12-14 (For 50N)
Tension for Compressor Belt, mm
8-10 (For 50N)
Tension for Steering Pump Belt, mm 8-10 (For 50N)
Clutch
Dry Single Disc with Diaphragm, spring-loaded,
Torsional absorber
Hydraulic Operation
Gearbox:
Type
Mechanical, Synchronizer for Forward Gears
Gear Ratio, 1st Gear
4.271, 3.986*
2nd Gear
2.283, 2.155*
Main Technical Data
Operating Parameters
Maximum Speed, Km/h
120, 150*
Maximum Slope, %
>30
Fuel Consumption at 50KM/h (Constant),
L/100Km
<8
Braking Distance at 50KM/h, m
臆22
Acceleration Noise, db (A)
臆78
Emission at idle speed, CO
HC
Smoke at Free Acceleration from Diesel Engine,
Rb
3.5
Capacity:
Fuel Tank, L
60
Engine Oil, L
4
Gearbox, L
2.4
Rear Axle, L
2.3
Steering Unit, L
1.0
Radiator, L
11
Adjusting Parameters:
5 -01
WARRANTY POLICY
This warranty does not apply to parts
worn due to natural wear and tear
and damages as a result of misuses
beyond their intended purposes, as
well as damages and losses that re鄄
sult from the use of disqualified fuel
and oils, illegal and improper use,
abuse (for racing or testing purpose),
even in the warranty period.
The consumable parts include bulbs,
brake disks, spark plugs*, filters,
tires, wipers, etc. These consum鄄
ables are warranted for three (3)
months or 10,000Km, whichever oc鄄
cur first.
The other exclusions include some
adjustment and measurement, such
as:
Adjust doors for better sealing in or鄄
der to avoid leakage or wind noise.
Front wheel alignment, tire balancing,
fuel consumption measurement and
engine tuning
The original parts replaced enjoy the
same warranty period as that of the
complete vehicle. The user will re鄄
ceive the original parts when his/her
vehicle is repaired at the franchised
JAC service providers. In this case
the parts can enjoy 12 -month war鄄
ranty coverage as of the date of re鄄
placement.
The manufacturer will assume no du鄄
ties that have not been expressly
defined by laws and regulations and
be responsible for losses due to the
user's violation of instructions clearly
specified in the "Operating Manual".
Please visit www.qiche365.org.cn to
download "User's Report on Defec鄄
tive Automobile Products" for more
information.
4
OWNER爷S MANUAL
pick-up
Port Timing
Exhaust Advance Angle 54毅
54毅
Exhaust Lag Angle
26毅
12毅
Intake Advance Angle
26毅
12毅
Intake Lag Angle
55.5毅
56毅
Fuel Filter
Integrated Steel
housing
Integrated Steel
housing
Air Filter
Dry, cyclonic, paper element
Oil Pump
External gear pump
Oil Filter
Integrated paper full flow filter
Cooling System
Auto -compensated, sealed type,
forced recirculation with centrifugal
pump, ribbon-tubular radiator
Main Technical Data
Electrical System:
Circuit
12V, single-line and negative, minus earth
Battery
90Ah, 68Ah*
Generator
60A, 14V
Engine
Structure
HFC4DA1-1
HFC4GA3(*)
Model
In -line, Four cylin鄄
der, Four Stroke
In -line, Four cylin鄄
der, Four Stroke
Type
Charger, I ntercooler,
Diesel Engine
MPI, Low -pressure
CR Petrol Engine
Bore伊Travel, mm
93伊102
85伊88
Displacement, l
2.771
1.997
Compression Ratio
17.5:1
10:1
Max Power, Kw
68
95
Ignition Sequence
1-3-4-2
1-3-4-2
Max. Torque, N.m/r/min 202/2100-2300
172/3000-4500
Fuel
Diesel
Petrol
Oil
APICI-4,
10W-30/15W-40
SF10W-30/10W-40
Min. f uel consump鄄
tion rate, g/kw.h
臆218
臆270
5 -03
Camber Angle 0毅30忆依20忆; Max. difference between LH
and RH Wheels: 20忆
Kingpin Caster
Angle
2毅45忆依25忆; Max. difference between LH
and RH Wheels: 25忆
Kingpin
Inclination
9毅依30忆
Toe-in
0-3mm
Same exposed length of LH and RH
straight Pull-rods.
Hub and Tires: 310
Hub
6J伊15
Wheel
215/75R15
Brake System
Independent front/rear dual hydraulic
brake system with vacuum booster, se鄄
ries dual chamber brake master cylinder,
load sensing proportioning valve
Service Brake
Front: disk brake; Rear: leading trailing
shoe brake; Drum Diameter: 260mm,
Shoe width:55mm
Hand Brake
Manual operation and cable transmission
for rear brake shoe.
Main Technical Data
3
rd
Gear
1.414, 1.414*
4
th
Gear
1.000, 1.000*
5
th
Gear
0.813, 0.813*
Rev
3.814, 3.814*
Chassis Type
Driveshaft
Split driveshaft with middle support
Rear Axle
Punched and welded axle housing, single-
stage hyperbolic gear. Final drive ratio: i:
4.1; For petrol model: 1:4.55 (*)
Frame
Punched and welded box-type frame
Front
Suspension
Independent suspension, torsion bar spring,
double cross-beam guiding structure, dou鄄
ble-acting telescopic shock absorber
Rear
Suspension
Parabolic tapered leaf spring -based de鄄
pendent suspension with double -acting
telescopic hydraulic shock absorber
Steering
Mechanism
Recirculating ball steering gear
Front Wheel
Alignment
5 -02
OWNER爷S MANUAL
pick-up
Thank you for selecting this JAC pick-up. We sincerely appreciate your trust in our products.
Your Vehicle and Environ鄄
mental Protection
The vehicle you select offers a
wide range of advanced fea鄄
tures, even in terms of environ鄄
mental protection.
This vehicle has been designed
in such a manner that it can min鄄
imize the adverse environmental
impact.
We always believe that you can
do more for the environmental
protection if you are willing to a鄄
bandon something. As a result,
we reject the materials that are
not good for environment such
as FCKW, cadmium and as鄄
bestos in plastic parts.
And we will not use chemical
solutions any longer for painting.
As is known to all, emission for
each engine has been con鄄
trolled to a low level.
You can enjoy quite engine run鄄
ning and low fuel consumption,
which also depends on your
driving habits.
Recovery has been considered
at the time of product design
and it is environment friendly.
Plastic parts are provided with
special marks as benefit intend鄄
ed re -use at the time of recy鄄
cling.
Recycled materials account for
a large proportion in these
plastic parts and in some cases,
it is even 100%.
All parts, including its manufac鄄
turing process, exclude from the
use of freon that could destroy
the ozone.
Your Vehicle and Safety
Your vehicle has typical safety
benefits in both active and pas鄄
sive aspects.
The active safety starts from the
chassis to ergonomic interior
trim design, while the passive
safety begins with the front
5
Vehicle Data
Engine Number
The engine number is stamped
on the cylinder body.
Nameplate
The nameplate is attached on at
the upper left of the front closure
in the engine bay, which details
brand, model, max gross weight,
engine model, unladen mass,
factory number, date of manu鄄
facture, VIN, etc.
VIN
The VIN is stamped or etched
into small metal strips that are
respectively riveted to the RH
side of front end cover of the
dash and obvious position above
rear RH wheel.
5 -04
OWNER爷S MANUAL
pick-up
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст