Chery Tiggo 5 (T21). Service manual — part 347
31–
92
31
HINT:
Resistance decreases as the temperature increases.
If result is not as specified, replace the evaporator temperature sensor.
2. Check the evaporator core assembly.
a. Check if the evaporator core assembly is cracked, damaged and leaked.
If any problem is found, replace the evaporator core assembly.
b. Check the fin for bends.
If any fin is bent, carefully straighten it with a
screwdriver or pliers.
3. Check the heater core assembly.
a. Check if the heater core assembly is cracked, damaged or leaked.
If any problem is found, replace the heater core assembly.
b. Check the fin for bends.
If any fin is bent, carefully straighten it with a
screwdriver or pliers.
Terminal 1 -
Terminal 2
-9
9316
23
2388
55
776
Multimeter
Connection
Temperature
(°C)
Specified
Condition
(Ω)
Temperature
(°C)
Specified
Condition
(Ω)
Temperature
(°C)
Specified
Condition
(Ω)
CAUTION
Resistance value may change even if the sensor is touched slightly. Make sure that the connector of
sensor is held firmly.
During measurement, the sensor temperature must be almost the same as the ambient temperature.
RT21310730
RT21310740
31–
93
31
4. Check the damper control mechanism assembly.
a. Check if the mode damper adjustment mechanism set is stuck, fell out, deformed or damaged. Replace
as necessary.
b. Check if the inner/outer circulation/temperature/face/defrost/foot damper set is stuck, fell out, deformed
or damaged. Replace as necessary.
Assembly
Assembly is in the reverse order of disassembly.
Installation
Installation is in the reverse order of removal.
CAUTION
If evaporator core is to be reused, do not insert the evaporator temperature sensor into a location where
the sensor was previously inserted. Insert it to a location that is 1 fin to the right or left of its previous
location.
During installation, apply a small amount of grease to the contact surface of mode damper adjustment
mechanism set to ensure that it can operate smoothly.
Always check that inner/outer circulation damper mechanism assembly operates normally after
installation is completed.
Always check that mode damper mechanism assembly operates normally after installation is completed.
Always check that temperature damper mechanism assembly operates normally after installation is
completed.
CAUTION
Tighten fixing bolts and fixing nuts to specified torque.
It is necessary to replace the refrigerant line O-ring when installing the refrigerant line. Failure to do so
may result in refrigerant leaks.
Lubricate the new rubber O-ring with clean refrigerant oil and install it to the refrigerant line joint.
Only use the specified O-ring, as it is made of special materials for R134a system.
Only use recommended refrigerant oil which is applicable to the A/C compressor assembly on vehicle.
Be sure to recharge the refrigerant and check refrigerant fo leakage after installation.
31–
94
31
A/C Low Pressure Line
Removal
1. Recover the refrigerant from the A/C system (
).
2. Turn off all the electrical equipment and ignition switch.
3. Disconnect the negative battery cable.
4. Remove the A/C low pressure line (compressor to evaporator).
a. Remove the fixing bolt (arrow) between A/C high/low
pressure line and expansion valve, and detach the A/C
low pressure line.
(Tightening torque: 7 ± 1 N·m)
b. Remove the coupling nut (arrow) between A/C high/low
pressure line fixing bracket and body, and disengage
the A/C low pressure line.
(Tightening torque: 7 ± 1 N·m)
c. Remove the coupling nut (arrow) between A/C high/
low pressure line fixing bracket and body, and
disengage the A/C low pressure line.
(Tightening torque: 7 ± 1 N·m)
CAUTION
Special service equipment for R134a refrigerant must be used to recover/charge refrigerant.
Always keep the work area in good ventilation.
The disconnected A/C line and connecting part should be sealed to prevent foreign matter from entering.
RT21310260
RT21310750
RT21310760
31–
95
31
d. Disengage the fixing clamp (arrow) between A/C low
pressure line and coolant circulation line.
e. Remove the fixing bolt (arrow) between A/C low
pressure line and compressor assembly, and
disengage the A/C low pressure line from the
compressor assembly.
(Tightening torque: 25 ± 2.5 N·m)
f. Remove the A/C low pressure line (compressor to evaporator).
Installation
Installation is in the reverse order of removal.
RT21310770
RT21310780
CAUTION
Tighten fixing bolts and fixing nuts to specified torque.
It is necessary to replace the refrigerant line O-ring when installing the refrigerant line. Failure to do so
may result in refrigerant leaks.
Lubricate the new rubber O-ring with clean refrigerant oil and install it to the refrigerant line joint.
Only use the specified O-ring, as it is made of special materials for R134a system.
Only use recommended refrigerant oil which is applicable to the A/C compressor assembly on vehicle.
Perform recharging for the A/C system and check refrigerant for leakage.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст