Chery Tiggo 5 (T21). Service manual — part 128
07–
98
07
7. Install the connecting rod bearing cap.
HINT:
The direction of the number on one side of connecting
rod is the same as that of the number on the connecting
rod bearing cap. These numbers are cylinder numbers
indicating at which cylinder are located. For example,
number 3 indicates that the mounting position is at No.3
cylinder.
a. Install the connecting rod bearing cap in place, and
screw the connecting rod bearing cap fixing bolts
(arrow) by hands, then tighten the connecting rod
bearing cap fixing bolts in two steps.
(Tightening torque: 1st step: tighten to 25 ± 3 N·m;
2nd step: retighten for 90° ± 5°)
8. Other assembly is in the reverse order of disassembly.
CAUTION
Pay attention to the front marks of piston and connecting rod during assembly without being reversed.
Install them with the side stamped with letter "481HK" on the connecting rod and piston top arrow facing
toward timing belt side as shown in the illustration.
481HK
RT21071270
481HK
481HK
RT21071280
3
3
RT21070950
CAUTION
Apply a small amount of engine lubricant to the connecting rod, connecting rod bearing cap and thread
joint surface.
1
08
SQR484F FUEL SUPPLY SYSTEM
Description 08-3
Specifications 08-4
Tools 08-5
Fuel Supply System Line Connection
Fuel Supply System Pressure Test
Removal 08-12
Installation 08-13
Removal 08-15
Installation 08-17
Removal 08-18
Installation 08-20
08–
3
08
GENERAL INFORMATION
Description
RT21080010
×3
×5
7
4
9
1
2
3
5
6
8
17
16
13
15
14
11
12
10
08–
4
08
Engine fuel supply system provides a certain amount and concentration of combustible air-fuel mixture and
supplies it to cylinders according to the requirements under various operating conditions of engine. Fuel
supply system consists of fuel tank assembly, electric fuel pump assembly, fuel filter assembly, delivery pipe,
fuel rail and injectors, and is used for fuel storage, filtration, delivery and injection.
Function of fuel supply system is to provide gasoline with sufficient pressure to fuel injectors by using electric
fuel pump assembly, and the injector injects a certain amount of gasoline to the top of intake valve in intake
manifold in accordance with control signals from ECM.
Specifications
Torque Specifications
Fuel Pressure Specifications
1 - Fuel Pump Pressure Cap
2 - Electric Fuel Pump Assembly
3 - Fuel Tank Seal Ring
4 - Fuel Level Sensor
5 - Fuel Tank Cap Assembly
6 - Filler Tube Assembly
7 - Fuel Breather Hose
8 - Fuel Filler Hose
9 - Fuel Tank
10 - Inlet Pipe I
11 - Inlet and Return Pipe Assembly
12 - Fuel Filter Assembly
13 - Fuel Tank Fixing Strap I
14 - Fuel Tank Fixing Strap II
15 - Fuel Tank Fixing Strap III
16 - Inlet Pipe II
17 - Fuel Rail Injector Assembly
Description
Torque (N·m)
Fuel Filter Ground Wire Fixing Nut
7 ± 1
Fuel Filter Bracket Fixing Screw
3.5 ± 0.5
Fuel Tank Pressure Cap
75 ± 5
Coupling Bolt Between Filler Tube Assembly and
Body
22 ± 2
Filler Tube Assembly Fixing Nut
7 ± 1
Fuel Tank Fixing Strap Fixing Bolt
25 ± 3
Fuel Level Sensor Fixing Screw
5 ± 1
Fuel Rail Fixing Bolt
8 + 3
Worm Clamp
3.5 ± 0.5
SQR484F
Pressure (kPa)
Fuel Pressure on Fuel Rail - Key (ON)
400
Fuel Pressure on Fuel Rail - Engine Idling
400
Fuel Pressure on Fuel Rail - Key (LOCK)
400
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст