Chery Tiggo 5 (T21). Service manual — part 153
12–
13
12
ON-VEHICLE SERVICE
Coolant Replacement
Coolant Draining
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the expansion tank cap when the engine temperature and radiator temperature are low.
4. Remove the engine lower left protector (
).
5. Put a coolant collector under the vehicle, rotate the
radiator drain cock plug (arrow) and drain the coolant in
the radiator and expansion tank.
HINT:
Put a drainage device or similar tool at the radiator outlet,
so that the coolant can flow into the collector smoothly.
6. After the coolant stops flowing, retighten the radiator drain cock plug.
WARNING
Always make sure engine is cold before operating cooling system.
Never open expansion tank cap or remove drain cock plug when engine is operating or cooling system
overheats. The overheated engine coolant and steam with high-pressure may flow out and cause
serious personal injury.
If your body contacts coolant accidentally, clean it with water immediately. If it is serious, please go to
hospital.
CAUTION
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
RT21120070
CAUTION
Tighten the drain cock plug to prevent leakage.
ENVIRONMENTAL PROTECTION
Wasted coolant should be handled by the specialized department according to local laws and
regulations. Never discard it at will.
12–
14
12
Coolant Adding
Only use coolant that meets Chery specifications.
Coolant Capacity
Coolant Concentration
1. Open the expansion tank cap and add coolant until the
coolant level reaches the "MAX" line.
2. Tighten the expansion tank cap, start and run the engine. Maintain the engine speed between 2000 and
2500 rpm to warm up the engine until the cooling fan operates.
Item
Capacity (L)
Cooling System
7.5
G11 Additive
Soft Water
50%
50%
WARNING
If it is necessary to add coolant when engine is hot, loosen expansion tank cap slightly first to release
internal pressure and loosen the cap completely after waiting for a while, and then add coolant.
If your body contacts coolant accidentally, clean it with water immediately. If it is serious, please go to
hospital.
CAUTION
DO NOT use inferior coolant.
DO NOT mix different colors or types of coolant.
Be careful when adding coolant; avoid spilling coolant on any area of engine.
MAX
MIN
RT21120030
12–
15
12
3. Stop the engine and wait until the coolant temperature drops to the ambient temperature. Check that the
coolant level is between "MAX" and "MIN" lines. If the coolant level is below the "MIN" line, repeat all
above procedures. If the coolant level is above the "MAX" line, drain the coolant until the level is between
"MAX" and "MIN" lines.
CAUTION
If there is no coolant in expansion tank after the engine just starts, perform the followings:
- Stop engine;
- Wait until coolant cools down;
- Add coolant to "MAX" line on expansion tank.
Run the engine at 2500 rpm until the coolant level becomes stable.
12–
16
12
Tank Upper Crossmember Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the engine trim cover assembly (
).
4. Remove the radiator grille assembly (
5. Remove the water tank upper crossmember trim board (
6. Remove the engine hood lock assembly (
7. Move away the hood lock cable from tank upper crossmember assembly.
8. Remove the tank upper crossmember assembly.
a. Press the clips on both sides of engine compartment
contact switch in the direction of arrow as shown in
the illustration, and remove the engine compartment
contact switch from tank upper crossmember
assembly.
b. Disconnect the connector (arrow) from engine
compartment contact switch, and remove the engine
compartment contact switch.
WARNING
Perform removal procedures with engine compartment at low temperature after cooling fan stops
completely, otherwise rotating cooling fan or hot components of engine compartment may cause serious
injury.
CAUTION
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
RT21120031
RT21120032
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст