Chery Tiggo 5 (T21). Service manual — part 475
43–
80
43
2. Apply a coat of primer M to the contact surface of body.
a. Using a brush, apply a coat of primer M to the contact
surface of body.
b. Width of primer is 13 - 15 mm.
3. Clean the contact surface of rear windshield.
a. Remove any residue on the contact surface of rear
windshield with a piece of clean cloth soaked with
glass cleaner.
CAUTION
Allow primer to dry for at least 3 minutes.
DO NOT apply primer to the adhesive.
DO NOT apply too much primer.
DO NOT keep any opened primer M for later use.
Primer M
Primer M
Primer M
Adhesive
RT21430350
CAUTION
DO NOT touch the surface of rear windshield after cleaning it.
RT21430360
43–
81
43
4. Apply a coat of primer G to the contact surface of rear windshield assembly.
a. Using a brush or sponge, apply a coat of primer G to
the glass rim and contact surface.
b. Use a piece of clean cloth to wipe off the excess
primer before drying.
c. Width of primer is 13 - 15 mm.
5. Mix the adhesive.
a. Using solvent, thoroughly clean the mixing board and
scraper.
b. Using a scraper, thoroughly mix 500 g main adhesive
and 75 g hardener on the mixing board.
6. Apply the adhesive.
a. Cut off the tip of the cartridge nozzle and add adhesive.
b. Install the cartridge to sealer gun.
c. Apply adhesive evenly to the rear windshield
assembly as shown in the illustration.
Adhesive width: 8 - 10 mm
Adhesive height: 11 - 13 mm
CAUTION
Allow primer to dry for at least 3 minutes.
DO NOT apply primer to the adhesive.
DO NOT apply too much primer.
DO NOT keep any of the opened primer G for later use.
Primer G
13-15 mm
RT21430370
CAUTION
Adhesive should be mixed thoroughly within 5 minutes.
RT21430380
11-13 mm
8-10 mm
RT21430390
43–
82
43
7. Install the rear windshield assembly.
a. Align the matchmarks on windshield and vehicle body,
and gently press in the windshield along the rim.
b. Uniformly apply adhesive to the windshield rim with a
scraper.
c. Remove any excessive or spilled adhesive with a
scraper.
d. Apply tape around the windshield, and remove them when the adhesive becomes hard.
8. Install the rear windshield weatherstrip.
9. Check and repair the sealing of glass.
a. Check the glass for leakage after adhesive has completely hardened.
b. If it leaks, seal the leaks by adding adhesive.
10.Install the rear spoiler assembly.
11.Install the rear wiper motor assembly.
12.Install the rear wiper arm assembly.
13.Install the back door protector assembly.
14.Connect the negative battery cable.
CAUTION
Check that lower/upper clearance and right/left clearance of rear windshield are uniform to ensure it is fit
well with the surrounding moulding.
Matchmarks
RT21430470
Adhesive
RT21430410
43–
83
43
Rear Window Defroster
General Information
Description
When rear window defroster switch is turned on, rear window defogger wire is heated to remove the fog, frost
or water vapors on rear windshield, thus realizing a clear view.
To turn on the rear window defogger, it is necessary to turn ignition switch to ON and press rear window
defogger switch. The rear window defogger switch indicator comes on while the rear window defogger
operation begins. The rear window defogger stops and the indicator turns off after pressing the rear window
defogger switch again.
RT21430490
Rear Window Defogger Wire
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст