Chery Tiggo 5 (T21). Service manual — part 470
43–
60
43
9. Remove the rear left door glass assembly.
a. Raise the rear door glass assembly to the proper position.
b. Remove 2 fixing bolts (arrow) from rear door glass
assembly, and remove the rear left door glass
assembly.
(Tightening torque: 9 ± 1 N·m)
Installation
Installation is in the reverse order of removal.
RT21430260
CAUTION
When installing rear door glass assembly, avoid the window glass from dropping and becomes
damaged.
43–
61
43
Rear Door Glass Rear Guide Rail Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the rear left door protector assembly (
).
4. Remove the rear left door assist grip mounting bracket assembly (
5. Remove the rear left door protective film assembly (
6. Remove the rear left door glass rear guide rail assembly.
a. Remove the rear left door frame weatherstrip.
HINT:
It is not necessary to remove the rear left door frame weatherstrip completely. There is a fixing screw in
the rear door frame weatherstrip.
b. Remove 2 fixing screws (arrow) from rear door glass
rear guide rail assembly.
(Tightening torque: 5 ± 0.5 N·m)
c. Remove the fixing bolt (1) from rear door glass rear
guide rail assembly, and remove the rear left door
glass rear guide rail assembly.
(Tightening torque: 9 ± 1 N·m)
Installation
Installation is in the reverse order of removal.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing rear door glass rear guide rail
assembly.
Appropriate force should be applied when removing rear door glass rear guide rail assembly. Be careful
not to operate roughly.
1
RT21430270
CAUTION
After glass regulating system is installed, make sure that the window glass can go up and down smoothly
and freely without any vibration, chattering or shock loading, etc.
43–
62
43
Rear Door Power Glass Regulator Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the rear door outer weather bar (
).
4. Remove the rear left door protector assembly (
).
5. Remove the rear left door assist grip mounting bracket assembly (
6. Remove the rear left door protective film assembly (
7. Remove the rear door glass rear guide rail assembly (
).
8. Remove the rear left door glass assembly (
).
9. Remove the rear left door power glass regulator assembly.
a. Disconnect the connector (1) from rear door power
glass regulator assembly.
b. Remove 6 fixing bolts (arrow) from rear door power
glass regulator assembly, and remove the rear left
door power glass regulator assembly.
(Tightening torque: 9 ± 1 N·m)
CAUTION
Make sure to wear safety equipment to prevent accidents when removing rear door power glass
regulator assembly.
Appropriate force should be applied when removing rear door power glass regulator assembly. Be
careful not to operate roughly.
1
RT21430280
43–
63
43
Inspection
1. Check rear door power glass regulator motor.
a. Apply battery voltage to the terminals of power glass
regulator motor connector, and check the operation of
power glass regulator motor according to the table
below.
If result is not as specified, replace rear door power
glass regulator assembly.
Installation
Installation is in the reverse order of removal.
RT21430290
1 2
-
+
Measurement Condition
Specified
Condition
Battery positive
(+)
Battery negative
(-)
1
2
UP smoothly
2
1
Down smoothly
CAUTION
After rear door power glass regulator is installed, make sure that the window glass can go up and down
smoothly and freely without any vibration, chattering or shock loading, etc.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст