Chery Tiggo 5 (T21). Service manual — part 74
06–
138
06
DTC
P0560-00 System Voltage Malfunction
DTC
P0562-00 System Voltage Low Voltage
DTC
P0563-00 System Voltage High Voltage
06–
139
06
ET21065015
BATTERY
ECM
MAIN
RELAY
10A
EF19
10A
EF17
10A
EF40
A2
F14
2-20
RL
A4
2-35
L
2-5
Br
A6
2-15
2-16
RR
R
86
87
85
30
ENGINE
COMPARTMENT
FUSE AND
RELAY BOX
IGNITION SWITCH
ON OR START
A1
A2
A3
A4
A5
A6
A7
A8 A9 A10
F12
F24
F11
F23
F10
F22
F9
F21
F8
F20
F7
F19
F6
F18
F5
F17
F4
F16
F3
F15
F2
F14
F1
F13
Gr
E-076
W
E-069
E-076
E-069
B
E-033
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1
2
3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4
5
6
7
8
9 10 11 12 13 14
1-47
Br
Br
1-48
E-028
2-63
B
B
2-64
E-026
ECM-2
E-033
ECM-1
E-035
37 38 39 40 41 42 43 44 45 46
47
48
25 26 27 28 29 30 31 32 33 34
35
36
13 14 15 16 17 18 19 20 21 22
23
24
1
2
3
4
5
6
7
8
9 10
11
12
B
E-035
06–
140
06
DTC Confirmation Procedure
Confirm that battery voltage is over 12 V before performing the following procedures.
Turn ignition switch to LOCK.
Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC).
Turn ignition switch to ON.
Use X-431 3G diagnostic tester to record and clear the DTCs stored in the ECM.
Select Read Code.
If the DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis procedure - Step 1.
If DTC is not detected, the malfunction indicated by the DTC is intermittent (
).
Diagnosis Procedure
a. Check if battery voltage is normal.
a. Check if battery terminals are loose or corroded.
DTC Code
DTC Definition
DTC Detection
Condition
Possible Cause
P0560-00
System Voltage
Malfunction
Ignition switch ON
Fuse
Wire harness or connector
Battery
Battery terminal
ECM
P0562-00
System Voltage Low
Voltage
P0563-00
System Voltage High
Voltage
CAUTION
When performing circuit diagnosis and test, always refer to the circuit diagram for specific circuit and
component information.
1
Check battery
Recharge or replace battery
NG
2
Check battery terminals
OK
Tighten or replace battery terminals
NG
OK
06–
141
06
a. Turn ignition switch to LOCK.
b. Check ECM grounds E-026 and E-028 (
a. Disconnect ECM connector E-033 and E-035.
b. Check ECM connector.
a. Measure voltage between ECM connector E-033 terminal
and body ground.
3
Check ECM ground point
Repair or replace ground wire harness or
ground point
NG
4
Check ECM connector
OK
Repair or replace ECM connector
NG
5
Check ECM power supply voltage (battery voltage)
OK
E-033
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1 2 3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4 5 6 7 8 9 10 11 12 13 14
-
+
V
RT21065052
Multimeter
Connection
Condition
Specified
Condition
E-033 (20) -
Body ground
Always
11 to 14 V
Go to step 8
OK
NG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст