Chery Tiggo 5 (T21). Service manual — part 330
31–
24
31
Diagnosis Procedure
Use the circuit diagram as a guide to perform the following procedures:
a. Turn ignition switch to LOCK.
b. Disconnect the negative battery cable.
c. Disconnect the HVAC control panel assembly connector K-012 and sun sensor connector I-021.
d. Disconnect the A/C wire harness connector K-007 and instrument panel wire harness connector I-039.
e. Check if wire harnesses are worn, pierced, pinched or partially broken.
f. Look for broken, bent, protruded or corroded terminals.
g. Check if related connector pins are in good condition.
a. Remove the sun sensor.
b. Install the new sun sensor to vehicle.
c. Use X-431 3G diagnostic tester to check if DTCs are still output.
DTC Code
DTC Definition
DTC Detection
Condition
Possible Cause
B2133
AC Solar Sensor Short
to Ground or Open
Circuit (Left Side)
Ignition switch ON
Sun sensor
Wire harness and connector
HVAC control panel
B2134
AC Solar Sensor Short
to Ground or Open
Circuit (Right Side)
CAUTION
When performing electrical equipment diagnosis and test, always refer to the circuit diagram for related
circuit and component information.
1
Check wire harness and connector
Repair or replace related wire harness and
connector
NG
2
Check sun sensor
OK
Replace sun sensor
NO
YES
31–
25
31
a. Turn ignition switch to LOCK.
b. Disconnect the negative battery cable.
c. Disconnect the HVAC control panel assembly connector
K-012 and sun sensor connector I-021.
d. Using a digital multimeter, check for continuity between
terminals of connector K-012 and connector I-021 to
check if there is an open in system according to the table
below.
Standard Condition
e. Disconnect the A/C wire harness connector K-007 and
instrument panel wire harness connector I-039.
f. Using a digital multimeter, check for continuity between
terminals of connector K-012 and connector K-007 to
check if there is an open in system according to the table
below.
Standard Condition
3
Check wire harness and connector (HVAC control panel assembly - sun sensor)
RT21311000
-
+
K-012
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
1
2
3
4
I-021
Multimeter
Connection
Condition
Specified
Condition
K-012 (36) -
I-021 (3)
Always
Continuity
K-012 (37) -
I-021 (1)
Always
Continuity
K-012 (30) -
I-021 (4)
Always
Continuity
RT21311010
-
+
K-012
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
K-007
1
2
3
4
5
6
8
9
10 11
13 14
15 16
18
17
21
20
22
7
12
19
Multimeter
Connection
Condition
Specified
Condition
K-012 (36) -
K-007 (5)
Always
Continuity
K-012 (37) -
K-007 (6)
Always
Continuity
K-012 (30) -
K-007 (16)
Always
Continuity
31–
26
31
g. Using a digital multimeter, check for continuity between
terminals of connector I-039 and connector I-021 to
check if there is an open in system according to the table
below.
Standard Condition
a. Turn ignition switch to LOCK.
b. Disconnect the negative battery cable.
c. Disconnect the HVAC control panel assembly connector
K-012.
d. Using a digital multimeter, check for continuity between
connector K-012 and body ground to check if system is
short to ground according to the table below.
Standard Condition
RT21311020
-
+
1
2
3
4
I-021
22 21 20
18
19
17 16 15
13
14
12 11 10
8
9
7
6
5
3
4
2
1
I-039
Multimeter
Connection
Condition
Specified
Condition
I-039 (5) -
I-021 (3)
Always
Continuity
I-039 (6) -
I-021 (1)
Always
Continuity
I-039 (16) -
I-021 (4)
Always
Continuity
Repair or replace related wire harness and
connector
NG
4
Check wire harness and connector (HVAC control panel assembly - body ground)
OK
RT21311030
-
+
K-012
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Multimeter
Connection
Condition
Specified
Condition
K-012 (36) - Body
ground
Always
No continuity
K-012 (37) - Body
ground
Always
No continuity
K-012 (30) - Body
ground
Always
No continuity
Repair or replace A/C wire harness and
connector
NG
OK
31–
27
31
a. Reconnect all disconnected connectors securely.
b. Connect the negative battery cable.
c. Turn ignition switch ON.
d. Use X-431 3G diagnostic tester (the latest software) to record and clear DTCs stored in the HVAC control
panel assembly.
e. Turn ignition switch to LOCK and wait for a few seconds.
f. Turn ignition switch ON.
g. Use X-431 3G diagnostic tester to read DTCs stored in the HVAC control panel assembly again.
5
Reconfirm DTCs
Replace HVAC control panel assembly
NG
System operates normally
OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст