Chery Tiggo 5 (T21). Service manual — part 369
32–
67
32
Spiral Cable
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Position the front wheels straight ahead.
4. Remove the steering wheel assembly (
5. Remove the combination switch cover (
).
6. Remove the spiral cable.
a. Disconnect the spiral cable wire harness connector
(arrow).
b. Detach the fixing claws (arrow) between spiral cable
and steering column.
c. Remove the spiral cable.
Inspection
1. Check the spiral cable.
a. Check that there are no scratches or cracks on the connectors, and/or no cracks, dents or chipping on
the cable.
WARNING
Wait at least 90 seconds after disconnecting negative battery cable to disable supplemental restraint
system.
RT21320060
A/C
PULL
rpm
×1000
MIST
OFF
OFF
REAR
ON
INT
INT
LO
H
I
RT21320080
32–
68
32
b. If there are scratches, cracks, dents or cuts on the
connectors or the spiral cable, replace the spiral cable
with a new one.
Installation
Installation is in the reverse order of removal.
HINT:
Always install the spiral cable correctly according to the
matchmarks on spiral cable and steering column (fully turn
the spiral cable clockwise slowly, then turn it
counterclockwise until yellow ball appears in the transparent
neutral window and align with the arrow marks), otherwise,
the spiral cable may be damaged.
RT21320090
RT21320100
CAUTION
Always install the spiral cable correctly according to the specified operating instructions.
DO NOT rotate the spiral cable over specified turns to prevent it from breaking.
Be sure to install the fixing claws in place when installing spiral cable.
Check that horn operates normally after installation.
Check the SRS warning light after installation, and make sure that supplemental restraint system
operates normally.
32–
69
32
Front Passenger Airbag
On-vehicle Inspection
1. Check the front passenger airbag (vehicle is involved in a collision but airbag is not deployed).
a. Perform a diagnosis system inspection.
b. Perform visual inspection with the front passenger
airbag removed from vehicle.
Check for cuts, cracks or discoloration on the front
passenger airbag.
Check for cracks or other damage on the connector.
Check instrument panel or instrument panel
crossmember assembly for deformation or break. If
any defect above is found, replace the front
passenger airbag with a new one.
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the glove box assembly (
).
4. Remove the front passenger airbag.
RT21320110
WARNING
Be sure to follow the correct procedures to remove and install front passenger airbag.
CAUTION
Handle the airbag and airbag control module assembly carefully, and never tap or strike them fiercely.
Removal, inspection and installation of airbag system must meet the relevant requirements and
specifications, and never perform operation casually.
The removed airbag should be kept properly. Store the airbag in a place with enough spare space to
prevent accidental airbag deployment.
WARNING
Wait at least 90 seconds after disconnecting negative battery cable to disable supplemental restraint
system.
32–
70
32
a. Remove 2 coupling bolts (arrow) between front
passenger airbag and instrument panel crossmember
assembly.
(Tightening torque: 10 ± 1 N·m)
b. Disconnect the front passenger airbag wire harness
connector (arrow).
c. Remove the instrument panel body assembly (
d. Using a flat tip screwdriver wrapped with protective
tape, slightly pry the fixing claws (arrow) around the
front passenger airbag mounting bracket to separate it
from the instrument panel body assembly.
e. Remove the front passenger airbag.
RT21320120
RT21320130
WARNING
DO NOT damage the airbag wire harness when handling airbag wire harness connector.
RT21320140
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст