Chery Tiggo 5 (T21). Service manual — part 499
47–
11
47
ON-VEHICLE SERVICE
Hood Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the hood upper adjustment block.
a. Turn the hood upper adjustment blocks counterclockwise
and remove the hood upper adjustment blocks (1).
4. Remove the hood lower adjustment block.
a. Turn the hood lower adjustment blocks counterclockwise
and remove the hood lower adjustment blocks (1).
WARNING
When removing hood assembly, an assistant is needed to hold hood. Prevent hood from dropping or
sudden closing to cause accidents during operation.
CAUTION
Be sure to wear safety equipment to prevent accidents when removing hood assembly.
When removing hood assembly, prevent hood from dropping to damage the body or front windshield
during operation.
RT21470040
1
1
RT21470060
47–
12
47
5. Remove the hood sound-absorbing pad.
a. Remove the clips (arrow) from the hood
sound-absorbing pad, and remove the hood
sound-absorbing pad.
6. Remove the front washer nozzle assembly (
).
7. Remove the washer hose.
a. Using a screwdriver wrapped with protective tape, pry
up the rubber cover (1).
b. Remove the washer hose from the clips (arrow).
8. Release the hood air spring assembly.
a. Using a screwdriver wrapped with protective tape, pry
up the clips on the upper part of hood air spring.
b. Release the hood air spring assembly.
9. Remove the hood assembly.
a. Remove 4 fixing bolts (arrow) between hood
assembly and hood hinge assembly, and remove the
hood assembly.
(Tightening torque: 23 ± 2 N·m)
RT21470050
1
RT21470051
RT21470070
RT21470080
47–
14
47
Adjustment
1. Adjust the hood assembly.
a. Loosen fixing bolts on hood hinge assembly.
b. Adjust clearance of hood assembly to standard range and pre-tighten fixing bolts on hood hinge
assembly.
Standard ranges of clearance between installation positions of hood assembly and each part are as
follows:
Clearance between hood assembly and radiator grille: 6.4 ± 1.5 mm.
Clearance between hood assembly and front headlight assembly: 6.5 ± 1.5 mm.
Clearance between hood assembly and front fender assembly: 4.0 ± 1.0 mm.
c. After adjustment, tighten the fixing bolts between hood hinge assembly and hood assembly to the
specified torque.
(Tightening torque: 23 ± 2 N·m)
d. After adjustment, tighten the fixing bolts between hood hinge assembly and body to the specified
torque.
(Tightening torque: 23 ± 2 N·m)
RT21470090
Hood
6.5±1.5
Hood
6.4±1.5
4.0±1.0
0±1.0
Hood
Radiator grille
Headlight
Front fender
47–
15
47
2. Adjust the height of hood front end with adjustment block.
a. Raise or lower the hood front end by rotating the upper
adjustment blocks clockwise or counterclockwise.
b. Raise or lower the hood front end by rotating the lower
adjustment blocks clockwise or counterclockwise.
c. After adjustment, make sure alignment between hood assembly and front fender assembly is within the
standard range.
Standard alignment: 0 ± 1.0 mm
3. Adjust the hood lock assembly.
a. Slightly loosen the fixing nuts of hood lock assembly
and adjust the hood lock assembly in the direction of
arrow as shown in the illustration.
b. Tighten the hood lock assembly fixing nuts to the specified torque after adjustment.
(Tightening torque: 10 ± 1 N·m)
Inspection
After the hood assembly is adjusted, perform the following inspections:
1. Check hood assembly for wear or deformation during installation, and repair as necessary.
2. Check if fixing bolts and fixing nuts are set in position. Tighten them to the specified torque as necessary.
3. Check if clearance and alignment between hood assembly and front fender assembly, radiator grille and
front headlight assembly are within the specified range, and adjust as necessary.
RT21470091
RT21470100
RT21470110
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст